HONDA GL1800 CB RADIO KIT INSTALLATION And REMOVAL

0

Filed Under (Honda) by admin on 20-11-2011

download
These instructions are for installation of the CB radio. For operation of the CB radio, refer to the Owner’s Manual and FCC Rule Book furnished with the CB radio. • Install the antenna which is sold separately between the installation of the rear trunk and the routing of the wire harness. • It is not necessary to drill four 7 mm holes and install the plate when you are also installing the CD changer. 1. Refer to the Service Manual to remove the right and left side covers and disconnect the negative terminal from the battery

2007 FJ Cruiser POOR SOUND QUALITY FROM SATELLITE RADIO REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
some customers may experience poor sound quality from the Toyota XM or SIRIUS satellite radio accessory option (sound quality is normal in AM, FM, and CD mode). A revised radio has been developed to remedy this condition. 2007 model year FJ Cruiser vehicles equipped with the upgraded radio and the port or dealer-installed Toyota satellite radio kit (XM or SIRIUS). PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 86120-35380 Same Radio Receiver

HARLEY DAVIDSON ADVANCED AUDIO CB RADIO KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
2006 models: communication switch 77173-06 2007 models: communication switch 77173-07 2008 models: communication switch 77173-08 FLHT models will require prior installation of: •Advanced Audio AM/ FM/ CD Radio Kit (76412-06) •AM/ FM Antenna Kit (76325-06 or 76317-06) Unless one has already been fitted as part of another Advanced Audio kit installation: 2006-2007 FLHX models will require the separate purchase of: •fuel tank console (61270-98A), •tank console gasket (71294-89), •a button-head screw (3652), •nut (7964) •clip (10103 and 10120). •tank pod mounting screws (2462) quantity 3 •FLHT trim piece (52447-96) and cb pod trim badge 2008 FLHX models: •fuel tank console (61270-08) •clips (10103 and 10120) NOTE The console screws, fuel door, gasket, mounting bracket will all need to be reused. FLTR models will require the separate purchase of: •a Console Pod Assembly (77136-03), and •three pan-head screws (2462). NOTE See a Harley-Davidson dealer for availability of optional decorative inserts for the Console Pod Assembly. ALL models will require the additional purchase of: •a Non-Ultra Overlay Harness (70169-06), and EITHER : •a Premium Stereo Helmet Headset (77147-98) OR a Hand-Held CB Microphone Kit (76312-98), All of these items are available from a Harley-Davidson Dealer. If two modules are already installed on top of the radio, two Dual-LockTM mounts, (76434-06), will be needed. Models WITHOUT a Tour-Pak installed will require the additional purchase of a Frame Mount CB Antenna Kit (76415- 06). Models WITH a Tour-Pak installed will require the additional purchase of a Tour-Pak Mount CB Antenna Kit (76414-06). All of these items are available from a Harley-Davidson Dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Electrical Overload It is possible to overload your motorcycle’s charging system by adding too many electrical accessories. If your combined electrical accessories operating at any one time consume more electrical current than your vehicle’s charging system can produce, the electrical consumption can discharge the battery and cause vehicle electrical system damage. See a Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories, or for necessary wiring changes. (00211b)

Incoming search terms:

HARLEY DAVIDSON FLHT ADVANCED AUDIO AM/FM/CD RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Remove Existing Equipment To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove outer fairing and windshield. Refer to OUTER FAIRING/WINDSHIELD REMOVAL in Service Manual. 3 2 1 is 00397 1. Socket head screw (4) 2. Radio support bracket (2) 3. Radio Figure 1. AM/ FM Radio Installation 3. See Figure 1. Using a long shank ball end socket (Snap- on® FABL6E or equivalent), remove the four socket head screws (1) to release the storage box from the left and right radio support brackets (2). Use the oblong holes in the fairing brackets to access the screws. Install Radio 1. Pull the storage box forward to remove the box from the opening in the inner fairing. Discard the storage box. 2. Position the radio (3) between the radio support brackets and push it into the opening in the inner fairing. 3. Align the threaded inserts in the sides of the radio with the oblong holes in the left and right radio support brackets. 4. Starting at the rear, install the four socket head screws previously removed. Alternately tighten the screws to 35- 45 in-lbs (4.0-5.1 Nm). 5. Plug the 23-place radio socket housing [27A] (part of the interconnect harness already installed on the vehicle) into the back of the radio. 6. Remove three T25 TORX® screws that hold the speaker opening cover on one end of the fairing. Discard the cover and screws. Install Speakers 1. See Figure 3. If the speaker (3) and adapter (4) are not assembled, or are assembled incorrectly, orient the speaker on the adapter and grille assembly so the speaker spade contacts are toward the side of the adapter with the widest edge. Snap the speaker into the adapter using finger pressure only.

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO XM SATELLITE RADIO KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
this kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHTCU (Ultra Classic® Electra Glide), FLHX (Street GlideTM) and FLTR (Road Glide®) model motor- cycles. XM satellite radio is available within the continental United States. It is not available in Alaska or Hawaii. Additional Parts Required FLHT models will require prior installation of an Advanced Audio AM/ FM/ CD Radio Kit (Part Number 76412-06) and an AM/ FM Antenna Kit (Part Number 76325-06 or 76317-06). Unless one has already been fitted as part of another Advanced Audio kit installation: FLHT, FLHTC, and FLHX models will require the additional purchase of a Non-Ultra Overlay Harness (Part Number 70169- 06) and a left-hand Antenna Bracket (Part Number 76456-06). FLHTCU models will require the additional purchase of an Ultra Overlay Harness (Part Number 70164-06) and a left-hand Antenna Bracket (Part Number 76456-06). FLTR models will require the additional purchase of a Non- Ultra Overlay Harness (Part Number 70169-06) and an Antenna Bracket (Part Number 76316-06). If two modules are already installed on top of the radio, two Dual-LockTM mounts, Part Number 76434-06, will be needed. These items are available from a Harley-Davidson Dealer INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. NOTE If another module has been installed in the location reserved for the XM radio module, relocate that module per the instructions supplied with that kit