YAMAHA PW 50Y SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 19-11-2010

download
Rear brake lever The rear brake lever is located on the left handlebar grip. To apply the rear brake, pull this lever toward the handlebar grip. EAU13182 Fuel tank cap To remove the fuel tank cap, turn it counterclockwise, and then pull it off. To install the fuel tank cap, insert it into the tank opening, and then turn it clock- wise. WARNING EWA11091 Make sure that the fuel tank cap is properly closed after filling fuel. Leaking fuel is a fire hazard. EAU13221 Fuel Make sure there is sufficient gasoline in the tank. WARNING EWA10881 Gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions. 1. Before refueling, turn off the engine and be sure that no one is sitting on the vehicle. Never refuel while smoking, or while in the vicinity of sparks, open flames, or other sources of ignition such as the pilot lights of water heaters and clothes dryers. 2. Do not overfill the fuel tank. When refueling, be sure to insert the pump nozzle into the fuel tank filler hole. Stop filling when the fuel reaches the bottom of the filler tube. Because fuel expands when it heats up, heat from the engine or the sun can cause fuel to spill out of the fuel tank. Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number [(R+M)/2] of 86 or higher, or a research octane number of 91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand or premium unleaded fuel. Use of unleaded fuel will extend spark plug life and reduce maintenance costs. Gasohol There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10% (E10). Gasohol containing methanol is not recommended by Yamaha because it can cause damage to the fuel system or vehicle performance problems

KYMCO MXU 300/ 250 SPECIFICATION AND OWNER'S MANUAL

0

Filed Under (Kymco) by admin on 12-11-2010

download
FRAMES ERIAL NUMBER The frames erial number is stamped on the front oft he frame. (1) Frame serial number (2) Engine serial number 11 (1) (2) (01) Rear brake lever (03) Front brake lever (04) Right front turn signal light (02) Headlights/Position lights (05) Steering handlebar lock (06) Left front turn signal light 12 PARTS LOCATION (01) (02) (02) (03) (04) (05) (06) (07) Right rear turn signal light (08) Ta illights/Stoplights (11) Exhaust system (12) Trailer hitch (13) License light (14) Battery (09) Instrument and indicators (10) Left rear turn signal light (09) (08) (08) (10) (07) 13 (14) (13) (11) (12) 14 (15) Drive select lever Tool kit (19) Reservoir water tank (20) Brake pedal fluid reservoir (16) Fuel valve (17) Seat (18) (16) (15) (18) (17) (19) (20) 15 (21) ) Choke knob (23) Recoil starter Exhaust system (22 (23) (22) (21) (24) Front brake lever ) Front cargo rack (26) Front brake fluid reservoir (27) Ignition switch (28) Rear (29) Accessory socket seat (30) Rear brake lever (31) (32) Leftfootpeg /Parking brake (25 brake fluid reservoir Headlight dimmer switch Starter button Hazard switch Turn signal switch Horn switch (33) Fuel fill cap (34) Throttle lever (35) Rightfootpeg (36) Rear brake pedal 16 (33) (34) (32) (31) (35) (36) (24) (25) (26) (27) (28) (29) (30) NOTE: Themachineyou have purchased may differ slightly from those shown in the figures of this manual. (37) Rear cargo rack ) Flagpole bracket (38

Incoming search terms:

1954 AJS MAINTENANCE MANUAL INSTRUCTION BOOK

0

Filed Under (AJS) by admin on 31-10-2010

download
Throttle twist grip. On right handlebar. Twist Inwards to open. When fully closed engine should just idle when hot. Air lever. Small lever on right handlebar Pull Inwards to Increase air supply to carburetter. Once set, when engine has warmed up, requires no alteration for different road speeds. Should be fully closed when starting engine from cold, Ignition lever. When fitted. Small lever on left handlebar. Advances and retards ignition point. Pull Inwards to retard. Retard two-fifths of total movement for starting. Valve lifter lever. Small lever close to clutch lever. Lifts exhaust valve from seat, releasing compression In combustion chamber, enabling engine to be easily rotated for starting. Also used for stopping engine if throttle stop is set as advised above. Clutch lever. Large lever on left handlebar. Grip to release clutch so that drive to rear wheel is disconnected. Front brake lever. Large lever on right handlebar. Grip to operate front wheel brake and, for normal braking, use in conjunction with rear brake application. Rear brake lever. Pedal close to left side foot rest. Depress with left foot to apply rear brake. Apply gently and use increasing pressure as the road speed decreases. Gear change lever. Pedal in horizontal position close to right foot rest. Controls selection of the four speeds, or ratios, between engine and rear wheel revolutions, with a ” free,” or neutral, position. See Illustration 2. Kick-starter lever. Vertical pedal on right hand side of gear box. Lighting switch, in top of head lamp. Controls lamps by a rotating lever which has three positions : (1) “OFF” Lamps not on. (2) ” L ” Pilot lamps, rear lamp and speedometer lamp on. (3) ” H ” Main head lamp, rear l amp and speedometer lamp on. Ammeter. In top of head lamp. Indicates flow of electric current, in, or out, of battery. (” Charge ” or ” Discharge.”) Horn switch. Press switch on right handlebar. Gear box filler cap. Located on top edge of kick-starter case cover. Allows Insertion of lubricant and access to clutch inner wire and internal clutch operating lever. Footrest for rider. Petrol tank filler cap. Located in top of fuel tank. To release, slightly depress, turn fully to the left, and then lift away. There are two locking positions. The middle position, between the fully tightened down and ” lift away ” positions, is in the nature of a ” safety ” device to prevent toss that might be occasioned by unauthorised meddling. Oil tank filler cap. Located on top edge of oil tank. The construction and operation is exactly as the petrol tank filler cap. Dipping switch. Trigger switch on left handlebar. Used to select normal or ” dipped ” beam of head lamp when main lighting switch lever is in the ” H ” position. (The main head lamp bulb has two filaments.)