2000 – 2005 Celica REAR DISC BRAKE PAD INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
A. Install the two brake pads with the anti-squeal shims to the brake caliper. B. Install the two (2) guide pins to fix the brake pads. 2. Install spring No. 1. A. Hook the spring upper portion to guide pin No. 1. Spring No. 1 B. Hook the spring lower portion to the center hole of the brake pad. 3. Install spring No. 2. A. Hook the spring upper portion to guide pin No. 1 Secure the guide pins with the retaining clip. A. Insert the retaining clip end into the hole of guide pin No. 1. B. Insert the other clip end into the hole of guide pin No. 2. NOTE: The retaining clip should be fully inserted into guide pin No. 1 and No. 2. If NOT, the guide pins will come off and the brake caliper will be damaged

Honda VTX 1800 Motorcycles ALL Models (Excluding C Model) Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Specifications Overall width 55.5 in. Overall length 108.06 in. Overall length w/ EZ-Steer 111.75 in. Wheelbase 72.44 in. Wheelbase w/ EZ-Steer 76.125 in. Load capacity 640 lbs. Brakes High-performance rear disc Tires 205/70R-15 Turning Radius 12.3 ft. Wheels Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20-25 psi · Suspension: “Zero-Flex” swing arm and two new (replacement) Progressive coil-over shocks. · Rear Differential: Champion Left Hand Drive Light Weight Rear Differential Assembly. · Brakes: Original front plus 2 high performance disc brakes at rear. · Storage Capacity: 6.75 cubic feet – 3 full-face helmets and additional over wheel storage. 2 Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) . · Passenger Seat and mounts (to be reinstalled without modification) . NOTE: OEM front and rear seat mounting bolts to be retained and reused. · Left and right passenger foot rests and mounts (to be reinstalled with modification) . · Mufflers (to be re-installed and relocated with minor modification) . · Rear Fender (complete w/ sub frame and all attaching parts) . · Swing Arm, Drive Shaft and Rear Wheel (complete w/ brake line and all attaching parts) . Core Return There are NO core return parts for this model. Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Use 17/64″ drill and drill through frame from inside out using passenger footrest mount holes as guide. b. Enlarge the passenger footrest mounting holes on the left and right side of the frame to 27/64″. c. Enlarge the holes in the left and right passenger footrest mounting plates to 27/64″. d. Clean area of all debris. 3.2 Relocate Regulator a. Install supplied “Z” bracket to the regulator as shown using the supplied hardware. b. Attach regulator to frame using the supplied hardware. c. Tie hoses down to avoid contact with the swing arm. Qty Description 1 ¼-20×2 hex head bolt 1 ¼-20×1-1/4 hex head bolt 6 ¼-20 Nyloc nut 10 1/4- SAE flat washer 4 as spacers 3.3 Hose Stay a. For models that have a recover tank below the swing-arm, a holder has been included keep the hose connected to the water pump away from the champion swing-arm. b. Remove the hose from the top of the recovery tank. c. Push the water pump hose forward against transmission. d. Secure hose with supplied stay as shown using existing bolt. Ensure that hose is not being crushed. Bend stay if necessary. e. Reconnect hose to recovery tank

Yamaha Road Star TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride

Incoming search terms:

HARLEY-DAVIDSON Sportster Solid Axle Suspension Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 24-26psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential, and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” approximately ¾”-1″ with a new belt or 1″ to 1-1/2″ with a used belt of total vertical movement. Do not use commercial belt dressing compounds on the belt except for Harley Davidson Poly-Oil, PN 99860- 81. These compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. The suspension is a “Zero Flex” solid axle with high performance adjustable pre-load coilover shocks. The suspension system is designed to give you the best ride with a load of no more than 400 pounds. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

HARLEY-DAVIDSON FLH/ FLT AND SOFTAIL (FLST) Owner's Maintenance Notes

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm, external differential and axle bearings are sealed and do not require greasing. However, should you experience unusual differential or axle bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Differential lubrication . Your differential is a sealed unit and comes filled with high-pressure grease. No maintenance is required. 5. Brakes . Check your brake system fluid level every 3,000 miles and top-off as necessary. Inspect rear disc brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P 6. Drive Train . Inspect your drive belt as recommended in your motorcycle Owner’s Manual. When properly tensioned after the trike conversion, the belt should “deflect” about 1/2 to 5/8 inches when pressed with a force of 10 pounds. Do not use commercial belt dressing compounds on the belt: these compounds are designed for friction, not toothed, belts and can collect dirt and sand. 7. Suspension System. FLH/FLT : The suspension system retains your two OEM shocks and is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). Keep the air pressure in the shocks in the range of 30-70 psig: Softail (FLST) : The suspension system retains your single OEM shock and adds two coil-over “helper” mechanical shocks. The system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight). There is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals.