Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

Suzuki 240 Hayabusa Swingarm Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain 7.) Rear Axel, wheel and brake assembly 8.) Pivot tube and swingarm
2.) New Swingarm Installation A. Most of the pieces needed are installed on the swing-arm. You’ll need to install the shock mount block with the 4 supplied flat head 5/16″bolts, use red loctite and torque to 25 ft lbs. B. Insert the 2 supplied pivot bushings in the pivot tube. Move your new swingarm into position. Once you have the swingarm in position reinsert the pivot tube to hold it in place. C. On some bikes (07′ and earlier Busa’s) it is necessary to grind approximately 1/8″ off the frame for chain clearance. Not all bikes will require this, but it is best to mock up and test fit before final assembly.

Incoming search terms:

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

Honda RC51 2000-2005 SBK Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 22-11-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Your subframe may be different but the cutting position is the same on all years. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary Replace all bodywork with fasteners loosely installed, mount undertail,
notice at bottom of the tray there are 2 holes, mark and remove tray, then drill holes in battery box 6) Inset lock into undertail using stock lock mounting clip, make sure the lock is in the correct position with the lock cable arm to function
properly. Insert undertail left side first, then right side, be carefull not to crack or scratch undertail. Use your stock plastic screw rivets to hold undertail in place. Attach lock cable to lock, check movement, adjust if necessary. Tighten all hardware on tail section, attach seat. * After this modification your undertail is not returnable. Paint is not war-
rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.
6) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

TOYOTA CELICA ADJUSTABLE REAR CAMBER LINK KIT INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 31-05-2011

Download
Securely block the front wheels of the vehicle. Use a jack to raise the rear end of the vehicle and support with jack stands. Remove the rear wheels. 2) Use a 14mm wrench and a 5mm Allen wrench to loosen and remove the nut on both end links where they meet the rear spindle assemblies. Use a 17mm wrench or socket to remove the bolt
and nut holding the rear upper link to the spindle. Retain all stock hardware. Use a 19mm and 17mm socket or wrench to remove the upper camber link bolt where it mounts to the sub-frame. Remove the stock suspension link and retain the stock hardware for later use. 4) Match the length of the Hotchkis arm to the center-to-center length of the stock arm. Use a 24mm wrench to loosen the jam nut and rotate the head. Lengthen the arm to add positive
camber and shorten the arm to add negative camber

Incoming search terms:

HARLEY DAVIDSON TOURING LOW PROFILE REAR SUSPENSION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION 1. Refer to the Service Manual and follow the instructions given to remove the seat. Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) 2. Disconnect the battery cables, negative cable first or remove the main fuse if equipped. 3. Raise the rear end of the motorcycle so that the rear wheel is just off the ground. Support the motorcycle with suitable blocking under the frame. NOTE Retain the original fasteners for installation of new shocks. 4. Remove the saddlebags from the motorcycle. See the Touring model’s Owner’s Manual for saddlebag removal. 5. Fasten the air pump, part number 54630-03A to the rear air suspension adjustment valve on the motorcycle. See the Touring model’s owner’s manual for valve location. Add 3-5 psi to clear the line but do NOT exceed 50 psi. 6. Using the pressure relief valve located below the gauge on the pump, release the air pressure from the rear sus- pension. Use caution when bleeding air from the suspension. Moisture combined with lubricant may leak onto the rear wheel, tire and/or brake components and adversely affect traction, which could result in death or serious injury. (00084a) 7. See Figure 1 and Figure 2. Remove the air hoses from the shock absorber air hose fittings

Honda CBR 900 RR Öhlins shock absorber kit Mounting instructions

0

Filed Under (Honda) by admin on 14-12-2010

download
Put the motorcycle on a stand so the rear wheel is clear of the ground. Make sure it’s steadily fixed so it will not fall over. 2 Remove the seat (2 screws from below) and loosen the six screws (four rear and two front) holding the fuel tank. The tank side covers must be loosened as well. 5 Remove the lower shock absorber mounting bolt from the triangle link. 6 Lower the shock absorber and turn it slightly so that it is possible to remove the horizontal attachment bolt. 7 Lift the rear end of the motorcycle enough to make removal of the shock absorber rearwards possible. 8 Attach the Öhlins shock absorber in reverse or- der. 9 Mount the upper and lower shock absorber bolts. 10 Attach the pre-load adjuster to the rear foot rest bracket on the right side of the motorcycle

240 tire V-Rod kit for stock swingarm Installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-11-2010

download
Recommended Parts and Supplies 1. Sawzall or comparable cutting tool. 2. Cut-off tool or jigsaw. 3. Shop or repair manual 4. Shop supplies, (loctite-red and blue, anti-seize, etc.) 5. Assorted hand tools. 6. 4-1/2″ grinder. 7. Drive pulley seal HD part # 11354K (qty.1) 8. Copper cap locking plate HD part # 35451-01K (qty.1) (The seal and locking plate can be re-used if not damaged during removal) Stock component removal To install the 240 kit, it will be necessary to raise the motorcycle off the ground on a suitable lift. WARNING – Be sure to center the motorcycle on the lift so that it does not fall over when you raise it up or when you are working on it. Installation of the 240 kit begins with the disassembly and removal of the rear end of the bike. Start with the simplest and most obvious components. For detailed information on removal of these parts, consult your factory manual. 1. Remove rear wheel assembly and brake. 2. Remove swingarm. 3. Cut brake tab on swingarm (as pictured). 4 4. Clean up casting mark on inside of swingarm in pulley area (as pictured). 5 5. Remove and replace right side swingarm mount with mount included in kit. 6. Install swingarm with new supplied pivot shaft. 7. Install stock spacer on left side of shaft, use supplied stepped spacer between stock spacer and swingarm. (Small step toward bearing). 8. Remove front pulley, and disassemble. 9. Test fit ½” allen bolts in hub before removal. Some models require drilling for bolts to fit. If necessary, use ½” bit and drill before removing, minimal material will be removed. Take caution not to drill too deep and hit case. 6 10. Install supplied adapter on the back to space pulley out. (Use loctite on bolts, and assemble as pictured).

Incoming search terms:

Kawasaki KFX 700 INSTALLATION and REMOVAL INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Jetting (see Picture on next page) 1. Remove vacuum slides from carbs. Remove stock needles & spacers, note order of assembly. 2. Install LTE needles on groove # 4 counting from the top down. 3. Remove stock main jets and replace with the supplied main jets. 4. Locate the fuel mixture screws. Using a flat blade screwdriver, turn the mixture screws clockwise until seated, then turn out 2.5 turns.
FINISHING UP Be sure all wires and hoses are zip-tied back so they will not touch the exhaust. QUIET CORES Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. FIRST RIDE Your first ride after installing exhaust should be no longer than 20 to 30 minutes. Let your ATV cool and re torque all of the hardware on your new exhaust. Silencer Packing

Incoming search terms: