650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Honda XR 400 Removal and Installation Manual

0

Filed Under (Honda) by admin on 09-12-2011

download
Turn Signal Switch Installation Front Wiring Connections Field Effect Transistor Installation Taillight Installation: Install the Acerbis DOT taillight over the empty well left in the stock fender using the two 5 x 20 mm bolts and 6 x 16 mm bolt found in the parts bag. Position the taillight over the previous taillight mounting well and transfer the hole locations for the top mounting holes onto the fender with a felt pen or snap punch (Photo 3) so that they are 3/8 of an inch above the edge of the taillight opening as shown in Photo 3. Drill two 3/16 inch holes for the top mounts. Attach the taillight using the top mounting screws, then pull the license plate holder down toward the bottom of the fender so that the taillight is pulled as horizontal as possible. Transfer drill a 1/4” hole at the bottom mounting location with the taillight in this position. When installing the bottom license plate mount bolt, make sure to install the 6 x 16 mm bolt from the bottom up to minimize the opportunity for the tire to grab it. Run the taillight
wires along the left frame rail using the stock wire clamps to support it. 8. Rear Turn Signal Installation: Turn signal mounting requires that you drill a 3/8 inch hole in either side of the rear fender near where it meets the side panels. You can achieve a clean,
durable installation using this mounting location. Mount the rear turn signals by drilling a 3/8 hole in the rear fender in the location shown in Photo 5, 3-3/4 inches back from the front edge (pointed tip of fender where it meets the side panel) and 2-3/4 “ up from the bottom edge Brake Light Switch Installation

Incoming search terms:

1100cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Receiver Hitch Installation Install all bolts loosely until all brackets are in place 1) Place motorcycle on center stand and be certain it is level. 2) Remove saddlebags if necessary for easier installation. 3) Mount bracket A to the lower front crash bar bolt Left side (new bolts provided) and top of left hitch arm. 4) Mount bracket B to the lower front crash bar bolt Right side (new bolts provided) and top of right hitch arm. 5) Bracket C mounts to rear of hitch and sub frame bolt located behind tail light (new bolt provided) This bracket mounts inside the rear fender. 6) Attach brackets D and E to rear of hitch. 7) Bracket F attaches to bottom of bracket D and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 8) Bracket G attaches to bottom of bracket E and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 9) Brackets D and E (with brackets F and G) attach to bottom rear saddlebag sub frame with U-bolts. 10) Tighten all bolts. INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Push the motorcycle off of the center stand and risers if used. 6. Bolt leanstop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them. see diagram next page 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

Sherco Engine Engine Removal and Case Splitting Manual

0

Filed Under (Sherco) by admin on 20-04-2011

download
Engine Removal and Case Splitting Preparation 1. Wash the bike and engine thoroughly. 2. Drain transmission oil by removing drain bolt and copper washer with 5mm Allen. 3. Drain coolant by removing 3 bolts of water pump cover and lifting off engine side case.4. Remove: a. rear fender- two bolts plus one long with washer using 4mm Allen b. fuel tank hose from petcock c. fuel tank- one short bolt and washer using 4mm Allen d. chain master link and chain from front sprocket e. kick starter- one large button head bolt and washer f. rear brake- one bolt/washer using 13mm wrench g. rear brake master cylinder- 2 button head bolts h. gear shifter- one bolt i. flywheel cover – 3 bolts j. clutch slave cylinder- two button head bolts using 4mm Allen k. clutch actuating rod by pulling it out of the case l. airbox three 4mm Allen bolts and loosening Phillips head carb hose clamp m. carburetor cap/slide assembly n. carburetor by loosening Phillips head manifold hose clamp o. spark plug cap p. spark plug q. header pipe 2 bolts into cylinder head r. silencer- 3 bolts (one with washer and nut using 10mm wrench) s. cylinder head coolant hose clamp and hose t. rear shock upper bolt u. radiator plastic cover bolt, then lever up the radiator with screwdriver until the radiator “legs” pop out of frame retaining holes 5. Remove flywheel using flywheel puller tool, taking care not to lose the small Woodruff
key by placing it inside of the magnetic flywheel for safe storage. 6. Remove ignition (3 bolts) and slide rubber grommet and ignition wiring assembly out of the case and out of the way, taking special note of the ignition timing marks. 7. Remove front sprocket and 2 retaining circlips. 8. Remove clutch side case and its 10 bolts using 5mm Allen, being careful not to lose to lose the 2 aluminum alignment pins (dowel pins). Insert the dowel pins into their holes within the Right Crankcase

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

HARLEY DAVIDSON BADLANDER SEAT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat strap from motorcycle. Retain all hardware. Discard seat strap. 2. Remove existing seat from motorcycle by removing Phillips head screw with lockwasher, and nylon washer from rear fender mounting bracket. Retain all hardware except discard nylon washer. 3. Disengage seat from frame tab at front of seat. 4. Install new seat onto motorcycle, making sure bracket on front of seat fully engages into seat mounting tab on frame. NOTE On rear fenders of 1997-1999 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997-1999 models. 5. On pre- 1997 models , secure seat onto rear fender with original screw and lockwasher and place guide washer (1) between seat bracket and rear fender. 5a. On 1997-1999 models , secure seat onto rear fender with original screw and lockwasher. After installing seat, pull upward on front of seat to be sure it is locked in position. If seat is loose, it could shift during vehicle operation, resulting in loss of control of vehicle and death or serious injury. 6. Use original hardware to install new seat strap (2) in same location as old seat strap. On FXSTC, Softail Custom models, fasten seat strap to fender support

HARLEY DAVIDSON DYNA SADDLEBAG KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVAL Remove Turn Signals 1. Locate and separate tail lamp connector (8-place multilock) under seat. Then remove wires from connector. Refer to AMP MULTILOCK ELECTRICAL CONNECTORS in Service Manual. 2. 1996-1998 Models: Pull turn signal wires through clips (if present) and rear fender. 1999 and Later Models: a. See Figure 1. Remove two screws and tail lamp lens (1) from base (2). b. See Figure 2. Using a Terminal Pick Tool (HD-41475- 100) (1), depress locking tabs and remove turn signal connectors (2-place) (2, 3). Save connectors for kit installation. Refer to AMP MULTILOCK ELECTRICAL CONNECTORS in Service Manual. c. Remove wires from turn signal connectors. Note location of terminal for proper reassembly. d. Remove turn signal wiring from clips under rear of fender and pull wires out

HARLEY DAVIDSON FLHTCUTG MUDFLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION 1. See Figure 1. Center drilling template on the rear fender. Adjust template to the bottom edge of the fender and tape template to fender. 2. Center punch the two template drilling locations. NOTE Use caution to prevent damage to the tire when drilling the attachment holes for the mudflaps. 3. Use a 5/16 inch bit to drill the template holes. 4. See Figure 2. Install the mudflap using one stud, washer and nut in each fastening hole. Tighten to 5-10 ft-lbs (6.8- 13.6 Nm) . 5. Repeat Steps 1-4 for the opposite fender.

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock