ULTIMA ELECTRONIC WIRING SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 03-03-2011

download
1. Find a mounting location for control box. The box is designed to be mounted to the top frame rail between split tanks, but can be mounted in a wide variety of places. If possible the box should be fastened using small screws or rivets but can be wire tied in place. Make sure the location is away from moving parts and heat sources. 2. Pre-fit harness to bike. Attach rear harness to control box. Each wire is color coded and labeled. Route individual wires to their destinations and do not cut to length. Keep wires in a bunch until they need to branch off. Use electrical tape to hold main wire bunch wherever individual or multiple wires branch off. Keep wires away from sharp edges or pinch points and leave extra wire for suspension movement. Repeat this for front and right/left harnesses. All wires not being used should be cut off at connector or secured to prevent shorts. When all wires are routed, cut excess length from ends leaving a couple extra inches for final fitment. 3 Remove pre-fitted harness from bike to install heat shrink tubing. Start at main connector and cut tubing approximately 1 inch past first branch. This will allow the next piece of tubing to slide into the first. Repeat this along entire harness. After encasing harness with heat shrink, use a heat gun to shrink tubing starting at main connectors. Be careful to not burn through the tubing with too much heat. Refit the harness to the bike, attaching to frame where necessary. Cut the ends of harness to length and strip the ends. Attach the terminals to the wire ends and use heat gun to shrink ends. Attach terminals to their destinations. 4. The diagnostic LED’s are used to locate shorts or overloads. Pinched or bare wires, faulty components or too much current draw usually causes these. If an LED is on, turn off the bike, locate and correct the problem, then turn the bike back on. The bike must be turned off to reset the protection circuit. If no LED’s are lit, but turn signals and dash lights do not work properly, make sure the control box main ground has a good connection to the chassis ground. 5. The control box operates the turn signals as listed: First command – flash 10 times then cancel Second command on same side – cancel Second command opposite side – cancel current sequence, flash 10 times then cancel Both sides at same time – hazard, all signals flash Brake switch – flash rear signals three times then stay on for 30 seconds

HARLEY DAVIDSON TRIBAR LED TAIL LIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse. Refer to service manual for location. 2. Remove seat using service manual instructions. 3. Remove rear tail light using service manual instructions. 4. Remove rear turn signals using service manual instruc- tions. 5. See Figure 1. Clip the cable strap (1) to free the rear harness from the chassis seat pan. 6. Unplug the 8-place connector (2) from the rear harness connector. 1 2 is05510 1. Cable strap 2. Harness connector Figure 1. Rear wire harness 1 2 4 3 is05511 1. Screws 2. Fender cover 3. Frame rail 4. Mounting bracket Figure 2. Remove Fender NOTE The fender support covers do not have to be removed from the upper shock absorber bolts. 7. See Figure 2. Remove the two rear fender support cover screws (1) and remove covers (2) and fender mounting -J04721 bracket (4). Repeat for opposite side and carefully remo ve fender and place it on a non-scratch surface. 8. See Figure 3. Clip and remove two cable straps (1). Pull wire harness three inches towards the license plate bracket. 9. Remove flange nuts (2) from both sides of license/tail light bracket stud plates (3) and remove bracket. Save stud plates and flange nuts. 1 3 2 is05517 1. Cable straps 2. Flange nuts 3. Stud plates Figure 3. Rear Harness Cable Straps, Flange Nuts and Stud Plates 10. Install new license/tail light bracket using stud plates and flange nuts previously removed. Tighten nuts to 5-6 ft-lbs (6.8-8.1 Nm) . 11. See Figure 2. Install rear fender by installing two screws (1) on each side through the fender support covers (2), frame rails (3) and into the fender mounting brackets (4). Tighten to 12-18 ft-lbs (16.3-24.4 Nm) 12. See Figure 1. Connect rear harness connector to 8-place connector on main harness. 13. Use a large cable tie strap from kit to secure the rear harness to seat pan. 14. Install rear turn signal lights using service manual instructions. 15. Verify that there is no excess wire harness near the stud plate then secure the harness with a large cable strap where the straps were previously removed. 16. See Figure 4. Secure the turn signal harness (3) to the stud plate (1) using small cable strap (2) and route the turn signal wire through the tail light bracket clip (4) as shown.