Kawasaki Vulcan 900 Installation and Removal Manual

0

Filed Under (Kawasaki) by admin on 25-04-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if applicable 3) Attach bracket C (left side) and bracket D (right side) to rearmost fender attachment bolt. A) If bike has no saddlebags use 3/8 spacer between bracket and motorcycle. Use new bolt provided. B) If bike has stock saddlebags use enclosed threaded rod assembly. 1) Thread rod into rear bag/fender mount 2) Place 3/8 spacer and bracket onto rod 3) Tighten down with locknut ensure locknut and rod are tight 4) Replace bags on rod and tighten NO BAGS STOCK BAGS
4) Remove rear riders pegs and attach front of bracket A(left side) and bracket B (right side) to rear foot peg mounting point. Mount foot peg to outside of bracket. Use new bolts provided. 6) Attach brackets C/D to top of rear hitch plate. 7) Attach rear of brackets A and B to TOP of hitch arms 8) Ensure hitch is square on motorcycle and tighten all bolts

Incoming search terms:

Ridley Auto-Glide Installation Manual

0

Filed Under (Ridley) by admin on 01-11-2010

download
Place motorcycle in a secure upright position 2) Remove saddle bags (if applicable) 3) Remove rear fender mounting bolts (3 each side) 4) Tap indicated rear fender mounting holes with a 3/8″ – 16 tap. (2 holes each side) It is highly recommended that cutting/tap oil is used. Use care when tapping holes. Be certain to tap holes completely through. 5) Ensure 2 large attachment bolts are tight. 6) Attach Bracket C (left) and Bracket D (right) to rear fender rail. Use new bolts provided on outer tapped holes (2) and one of the longer original bolts for center hole. Place one washer between brackets C & D and rear fender rail on each bolt. (3 each side) Place washer and thin nut on inside of rear fender on new bolts (2 each side) These replace original fender washers. It may be necessary to reattach saddle bag attachment hardware when attaching brackets C and D. All saddle bag hardware should be attached to the OUTSIDE of brackets C and D. 7) Attach front of Bracket A (left) and B (right) to existing hole in motorcycle frame just above swing arm pivot. 8) Attach rear of bracket A (left) B (right) to TOP of forward hitch arms. Snug bracket A and B attachment bolts at this time. 10) Attach top of Bracket E (left) and F (right) to outside of lower tabs on bracket C & D. 11) Attach bottom of brackets E and F to top of rear hitch plate. 12) Tighten bolts at this time. Use caution not to over tighten and strip tapped holes in rear fender rail. Bracket Identification

BMW K100 Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1) Place motorcycle on center stand and remove saddle bags. 2) Loosen seat and top body panel bolts. 3) Remove rear fender and trim to accommodate bracket E. 3) Attach bracket E to rear frame below tail light with U-bolts provided. NOTE: Do not over tighten U-bolt and crush frame. 4) Attach bracket A(left) / B(right) to rear foot peg attaching bracket. Use new bolts provided. 5) Attach bracket C(left) / D(right) to BOTTOM of tab on brackets A and B. 6) Attach rear of brackets C/D to BOTTOM of forward hitch arms. 7) Attach bracket F to top of rear hitch plate and bottom of bracket E. 7) Carefully tighten all bolts ensuring hitch is square with motorcycle. Tighten seat at body panel bolts at this time as well. 8) Reattach rear fender. NOTE: Recheck bolts for tightness for the first several hundred miles. Retighten if necessary.

Incoming search terms: