HARLEY DAVIDSON MOUNTING BRACKET SERVICE MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
INSTALLATION 1. See Figure 1. Note position of mounting brackets (1). Remove old mounting brackets and discard. NOTE On 1997-2000 models, the air fittings are installed to the two mounting holes on the right-hand right side bracket. On 2003 and later models, the single air fitting is installed to mounting hole on the left-hand side bracket. 2. See Figure 2. Install new mounting brackets from kit on each side of the motorcycle using new locknuts as follows: a. Use the 5/16-18 x 1 inch screws (5) in the upper two holes with 2 chrome washers (3) placed between the mounting bracket and the saddlebag support at each of the two locations. Install a 5/16-18 flange locknut (2) behind the screw that does not screw into a weld nut. Tighten to 15-19 ft-lbs (20-26 Nm). b. On each side, install a 1/4-20 x 7/8 inch screw (9) through the bottom hole of the mounting bracket and the saddlebag bracket as shown, with a chrome washer (3) placed between the mounting bracket and the saddlebag bracket. Tighten to 10-14 ft-lbs (13.5- 19.0 Nm). On 1997-2002 models, install the air line fittings to the lowest two holes drilled in the right side bracket. On 2003 and later models, install the single air line fitting to the lower front hole drilled on the left side bracket. c. See Figure 2. On each side, attach docking points (6) in their proper location on mounting bracket with 3/8- 16 x 1-1/2 in. buttonhead screws (7), washers (3) and locknuts (8) but leave locknuts slightly loose so docking points can be adjusted for proper fit. On 1997and later models, the docking point will attach through the front hole of the mounting bracket as shown. On 1994-1996 models, the docking point will attach through the rear hole of the mounting bracket. d. Place detachable passenger backrest into docking points as described in the Backrest Instruction Sheet. Make sure that the forward notches of the sideplates are pushed completely into the forward docking points, then tighten the rear docking points securely to 45-47 ft/lbs (61.0-64.0 Nm

Incoming search terms:

HARLEY DAVIDSON FRONT AND REAR FENDER TIP TRIM INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation GENERAL The original equipment (stock) fender tip lamp assemblies must be removed and the wire(s) must be unplugged or removed as specified in the following instructions. FRONT FENDER TIP REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1994 AND LATER FLT MODELS 1. Refer to the applicable FLT Service Manual. Remove headlamp assembly with housing. 2. Locate the 3-place connector [32 in wiring diagram] through which 12vdc and electrical ground are connected to the fender tip lamp assembly. The connector locations are as follows: FLTC Ultra: Under fuse and circuit breaker block FLHT/C/C-U: On bottom of left outer fairing bracket FLHR: On left front above air suspension valve NOTE Before disassembling the connector in the next step, refer to the applicable wiring diagram and check wire colors and connections to assure that connector [32] has been located. 3. Refer to the “DEUTSCH ELECTRICAL CONNECTOR” section in the FLT Service Manual and remove the leads, connected to the fender tip lamp, from the socket half, connector [32B]. 4. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 5. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wires connected to lamp assembly. 6. Reach under left side of fender and gently pull wires through rear hole in left side of fender and then through clips on left side of fender and finally through front hole and out of trim strip. REMOVAL OF STOCK FRONT FENDER TIP LAMP ON 1993 AND EARLIER FLT MODELS, FLSTC AND FLSTN 1. Insert a small screwdriver blade in rectangular slot at top center of fender tip lamp lens and gently pry lens from lamp. 2. Remove two screws and nuts that fasten fender tip lamp assembly to front fender. Gently remove the lamp assembly taking care not to damage wire connected to lamp assembly. 3. Unplug wire connector located about 3 in. from lamp assembly. Cover the socket half of connector (connected to motorcycle wiring) with electrical tape. INSTALLING FRONT FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in fender and guide outer ends of fender tip trim into trim strips on sides of fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs . REAR FENDER TIP REMOVAL OF STOCK REAR FENDER TIP LAMP ON ALL MODELS Follow steps 1 through 3 given above for “1993 AND EARLIER FLT MODELS, FLSTC & FLSTN” INSTALLING REAR FENDER TIP TRIM FROM KIT-ALL MODELS 1. Position fender tip trim over holes in rear fender. 2. Insert studs on fender tip trim through holes in fender and secure with locknuts included in kit. Tighten locknuts to 6 in-lbs

Incoming search terms:

HARLEY DAVIDSON RIGID MOUNT SIDEPLATE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
INSTALLATION (2000 THROUGH 2002) Refer to the instructions included with kit 53388-03 for installation on 2000 through 2002 models. INSTALLATION (2003 AND LATER) NOTE To keep the fender aligned, completely install the sideplate on one side of the motorcycle before proceeding to the second side. The sissy bar should be installed last. 1. For models equipped with saddlebags: a. Remove the saddlebag, and retain the mounting hardware for later reinstallation. b. See Figure 1. Remove the bolt (A) and washer (4) that secures the rear fender to the fender brace. Discard the bolt and washer. Remove and retain the two saddlebag mounting studs (C) and nut plate (D) for later use. For models NOT equipped with saddlebags: a. See Figure 1. Remove the two rearmost bolts (A), washers (4) and nut plate that secure the rear fender to the fender brace. Discard the bolts and washers. b. Remove the bolt (B) and washer (4) that secure the fender and brace to the frame. Discard the bolt and washer. 2. See Figure 1. Position the correct sideplate to the outside of the fender brace. 3. With saddlebags: Apply LOCTITE 243 (blue) to the 3/8- 16 threads of the saddlebag mounting studs (C) and reinstall the studs through the sideplate, fender brace, frame and fender, and thread into the stock nut plates (D). Install one chrome 3/8-16 screw (3) and chrome washer (4) from the kit through the rear hole in the sideplate, fender brace and fender, and thread into the stock nut plate (D). Without saddlebags: Install three chrome 3/8-16 screws (3) and chrome washers (4) from the kit through the holes in the side plate, fender brace and fender, and thread into the stock nut plates (D). 4. Repeat steps 1-3 for the opposite side. 5. Install a sissy bar (not included in the kit) into the side- plates. Apply LOCTITE 262 (red) to the threads of the chrome 1/4-20 capscrews (5) and insert them into the sideplate holes. Tighten to 8-10 ft-lbs (11-14 Nm) . 6. Tighten the bolts (3) and/or saddlebag mounting studs to 21-27 ft-lbs (28.5-36.6 Nm) . 7. Reinstall the saddlebags

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms:

HONDA NRX RUNE CALIPER COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Starting on the right side hold the cover in place over the brake caliper. See photo (1), note how the spring when installed wraps around the bleeder screw (1A) at the front of the cover. See photo (2), note how the spring at the rear of the cover is routed behind the brake pad retaining pin. Using one of the springs supplied hook both ends of the spring into the holes at the front edge of the cover. Clean the face of the caliper (area marked “Nissin”) with rubbing alcohol. Peel the backing from the adhesive tape on the inside of the cover. Carefully position the cover in place aligning it with the suspension arm and being sure it is seated flat against the caliper. Press firmly to secure the tape to the caliper. Next stretch the spring over the bleeder as shown in photo (1A). At the rear of the cover route the spring behind the brake pad retaining pin as shown in photo (2A). Hook the spring into the upper hole then using a piece of fine wire or string (dental floss works good) hook onto the open end of the spring as shown in photo (3). Pull the hook into the hole in the cover. Remove the wire or string. Check again to see that the cover is seated on the caliper and that the springs are secure and not interfering with the moving parts of the brakes. 2. Repeat on the left side caliper. Rear Caliper Cover 1. Set the cover in place over the caliper. Notice that you need to hook the top of the cover over the caliper and the location of the two small spring holes at the front and back of the cover. The long spring supplied will attach to the front hole, pass between the caliper housing and the backside of the brake pad, then attach to the rear hole

Incoming search terms:

TRIUMPH AMERICA AND SPEEDMASTER SOLO RACK FITS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Remove the 8mm bolt from the rear of the passenger seat. Remove the passenger seat by pushing the seat forward and lifting up at the front edge of the seat. Remove the 12mm bolt from the rear of the drivers seat. 2. From the supplied hardware locate the two socket head screws and washers, place the large washers onto the screws with the polished side of the washer facing the head of the screws. Place the small screw and washer thru the small hole in the rear of the solo rack, place the black plastic spacer supplied onto the screw on the bottom side of the solo rack. Holding the rack in place on the rear fender, start the screw in the rear hole. Install the remaining large screw with its washer into the front hole and tighten both screws securely.

Incoming search terms: