2003 – 2004 4Runner REAR SEAT CENTER ARMREST CUP HOLDER REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
The ends of the zipper are concealed in the cover. Pull out both ends of the zipper from the cover. B. To unlock the zipper, flip the zipper’s tab so that it points away from the direction the zipper will be opened. C. Open the zipper by pushing the tip of the tab. 3. Roll Up Cover. A. After opening the zipper, roll up the cover. B. Roll up the cover until the foam pad’s 3 holes are revealed. 4. Remove Cup Holder. A. Remove the screws from each of the 3 holes. B. Pull the cup holder out of the armrest. If the cup holder is difficult to remove, hold the armrest with the cup holder facing down and shake the armrest for cup holder remova

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

2005-2008 TOYOTA TACOMA/ TUNDRA

0

Filed Under (Toyota Manuals) by admin on 09-06-2011

Download
anti-Skid Brakes (ABS) STD Global Outstanding Assessment body (GOA) STD Toyota Safe-T-Cell STD Driver’s SRS airbag STD Front passenger SRS airbag STD Driver’s pre-tensioner seatbelt STD Driver’s forcelimiter eatbelt STD Front passenger pre-tensioner seatbelt STD Front passenger forcelimiter seatbelt STD Height adjustable front seatbelts STD 2nd row/rear seat centre position lap/sash seatbelt STD 3rd row lap/sash outboard seatbelts STD 2nd row/rear seat ALR outboard seatbelts for child seats STD

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DELUXE SEATS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
These kits fit 2005 and later FLSTN model motorcycles. Additional Parts Required NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 3 and Table 1. INSTALLATION 1. Remove existing seat according to Owner’s Manual Instructions. Save all attaching hardware. 2. See Figure 1. Install two flange nuts (1) from kit onto the seat mounting studs. Tighten flange nuts to 5-8 ft-lbs (7- 11 Nm) . 1 is03023 1. Install flange nuts Figure 1. Flange Nut Locations NOTE See Figure 3 for Steps 3-6. 3. Remove two screws (A) and rear mounting bracket (B) from stock seat. Save all hardware. 4. Install the rear mounting bracket (B) removed in Step 3 onto the new seat using the seat bracket screws (A). Tighten screws to 19 in-lbs (2.1 Nm) . 5. Install new seat (1) on the motorcycle by inserting the tab at the front of the seat into the slot at the rear of the fuel tank. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. Fasten rear seat bracket (B) to fender nut using stock mounting screw (C). 7. See Figure 2. To install grabstrap, remove front screw and washer from rear fender support. Install grabstrap with thick washers (1), thin washers (3) and screws (4) from kit. Tighten to 21-27 ft-lbs (28-37 Nm)

HARLEY DAVIDSON DYNA PASSENGER PILLION SEAT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVE SEAT NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove screw to detach rear seat mounting bracket from fender. 2. Remove two capscrews that attach seat mounting bracket to bottom of stock seat. 3. Remove the existing seat from the motorcycle. Save the seat bracket and mounting screws for installation of the new seat. 4. If motorcycle has a grabstrap installed, remove nut and washer that holds passenger strap in place and remove strap. 5. See Figure 1. Remove the plastic cap from rearmost fender hole (3). 6. Remove the seat retention nut and washer from the solo seat mounting hole. 7. See Figure 2. A cable strap may be used as an installation aid to remove and reinstall the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the rearmost fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. 8. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap. 2 5 1 2 1 3 6 7 4 is00363 1. Retention nut and washer (2-up seat positon) 2. Retention nut and washer (solo seat position) 3. Rear-most fender hole 4. Middle fender hole 5. Grabstrap mounting hole 6. Flange screw 7. Plastic retention nut

HARLEY DAVIDSON XL SOLO CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. 1 2 4 1 3 is03341 1. Stock retention nut and washer 2. Plastic cap 3. Rearward fender hole 4. Center fender hole Figure 1. Retention Nut and Plastic Cap Location 2. For models that had a solo seat: Proceed to Step 3. For models that had a 2-up seat: The retention nut and washer must be moved from the rearward mounting hole to the center fender hole where the rear seat bracket will be attached. Use a cable strap to aid in this step as fol- lows: a. See Figure 1. Remove retention nut from rearward fender hole (3) and plastic cap (2) from center fender hole (4). b. Install plastic cap into the rearward fender hole. c. See Figure 2. Place the retention nut over the cable strap so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the center fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib of the retention nut seated into the notch in the fender hole, slide the retention washer into place from the rear. This will lock the retention nut in place. 3. Position the solo seat on the motorcycle frame with the mounting bracket at the rear. Bring the seat forward and engage the tab on the seat into the slot at the base of the fuel tank. 4. See Figure 3. Secure the seat to the fender using the knurled knob (3) and neoprene washer (4) from the kit. Install the washer on the knob and tighten the knob securely to the fender seat nut

HARLEY DAVIDSON FXD SOLO SADDLE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
Removal of Stock Seat 1. Remove screw (6) to detach rear seat mounting bracket (9) from fender. 1996 models will have a nylon washer under the bracket that should also be saved for installation of new seat. 2. Slide seat rearward to unhook front of seat from frame, then pull seat forward out of passenger strap. 3. Remove two capscrews (10) that attach seat mounting bracket to bottom of stock seat. Install original seat mounting bracket to bottom of new solo saddle with original capscrews. Tighten capscrews securely. 4. Remove nut (7) and washer (8) that hold passenger strap (11) in place and remove strap. Installation of Kit Seat This seat is for solo driver use only. Do not attempt to carry a passenger with this solo seat installed. Use of a luggage rack, fender, or tail section as an additional seat may result in death or serious injury. NOTE When a solo seat is installed without a passenger seat, the passenger footpegs or footboards and the passenger grabstrap must be removed. For 1996 models: 1. Slide seat into position until front seat tab engages frame, then place original nylon washer under hole in rear seat mounting bracket and secure bracket to fender with screw (6). NOTE For 1997 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 models: 1. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 2. Place retention nut (3) over cable strap (2) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 3. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 4. Slide seat into position until front seat tab engages frame, then secure rear seat bracket to fender with screw (6). Install chrome cap (5) in rear retention nut

Honda VTX 1300 Motorcycles All Models Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black f. Install supplied Canister/Regulator bracket with supplied hardware. Figure 3. Make sure the hoses/electrical wires are routed underneath the bracket as shown. Figure 4 Qty Description 2 3/8-24×1-3/4 hex head bolt 4 3/8 SAE flat washers 2 3/8-24 Nyloc nuts g. Install Canister and Regulator with supplied hardware. Figure 4 Qty Description 4 ¼-20×1-1/4 hex head bolt 8 ¼ SAE flat washers 4 1/4-20 Nyloc nuts

Yamaha Road Star Trike Conversion Installation Manual

0

Filed Under (Yamaha) by admin on 17-02-2011

download
Removal of Original Parts a. Disconnect the battery. b. Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. c. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for re-installation after modification are noted. • Rider’s Seat (to be re-installed without modification) • Passenger Seat (to be reinstalled without modification) NOTE: OEM front / rear seat mount bracket and rear seat mounting bolt to be retained and reused. • Passenger Back Rest w/ Mounting Rails (to be re-installed without modification) NOTE: Back rest to mounting rail hardware to be reused. Mount rail to vehicle frame not to be reused. • Left and right passenger foot rests (to be re-installed without modification) • Drive Pulley / Belt cover (to be re-installed without modification) • Mufflers (to be re-installed and relocated with minor modification) • Rear Fender (complete w/ sub frame and all attaching parts) NOTE: Upper Forward Fender Mounting Bolt to be retained and reinstalled. • Shock Absorber to Swing Arm Mounting Bolt (to be re-installed) • Swing Arm and Rear Wheel (complete w/ all attaching parts) NOTE: Swing Arm Pivot Bolt, washer and nut to be retained and reinstalled. • Brake Line to Rear Master Cylinder • Drive Belt Core Return There are NO core return parts for this model Installation of Champion Trike Conversion Kit 4.1 Install Drive Belt a. Install supplied drive belt to transmission output pulley. (Refer to OEM manual) Figure 1 b. Drive belt cover to be reinstalled later. 4.2 Install Champion Swing Arm a. Install Champion Swing Arm to vehicle using the OEM pivot bolt, washer and nut. Figure 2 b. Attach OEM shock absorber to swing arm using OEM hardware. c. Torque pivot bolt nut to 90 lb. ft. d. Torque lower shock hardware to 43 lb. ft. 4.3 Install Rear Drive Assembly a. Install tension bolts and jam nuts to adjuster

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Incoming search terms: