Harley Davidson Sportster 4 Piston Rear Brake Caliper installation Manual

0

Filed Under (Harley Davidson) by admin on 02-04-2012

download
Installing Rear Caliper – Sportster Models Removing The Stock Brakes SPORTSTER REAR BRAKE SYSTEM 84 & UP MODELS The basic steps are the same to install a PM rear brake caliper kit on any of the late model Harley Davidson “swingarm” style motorcycles; all require the removal of the rear wheel. Using a suitable lift, raise the motorcycle high enough off the ground to allow you to remove the rear wheel assembly. PHOTO 2 W a r n i n g Center the motorcycle on the lift so that it will not fall while you are working on it. Photo 2: Remove the rear brake caliper assembly by unscrewing the 2 caliper mounting bolts that go through the caliper into the caliper mounting bracket. Lift the caliper up and off the mounting bracket and brake rotor, move the caliper back out of your working area. Don’t remove the brake line from the caliper yet; you will do this just before you are ready to hook it up to the new caliper. The brake pads are held into the caliper mounting bracket by 2 spring clips; slide the brake pads out of the mounting bracket and remove the retaining springs. PHOTO 3 Remove Cotter pin and rear axle nut, slide rear axle completely out. Photo 3: Remove nut from Right rear shock and rotate belt guard up. Slide belt off of pulley and roll rear wheel back 6 – 8″. Photo 4: Remove original caliper bracket from swingarm

Incoming search terms:

2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

HONDA XL600R REAR WHEEL/BRAKE, SUSPENSION SERVICE INFORMATION

0

Filed Under (Honda) by admin on 28-11-2011

download
The rear shock absorber contains nitrogen under high pressure. Do not allow Brake dust may contain asbestos which can be harmful! to your health. Do not use compressed air to clean brake drums or brake panels. Use a vacuum with a sealeddust collector. Wear a protective face mask and thoroughly wash your hands when finished.

YAMAHA FZR600 SPECIFICATIONS AND SERVICE MANUAL

0

Filed Under (Kawasaki) by admin on 27-04-2011

download
Front Axle and Outer Tube Front Wheel Axle Holder Rear Axle and Nut Handlebar Crown and Inner Tube Handlebar Crown and Steering Stem Steering ring nut (Upper and lower) Brake Caiiper (Front/Rear) Bleed Screw and Brake Caliper Brake Hose and Union Bolt Front Master Cylinder and Cylinder Cap Front Fender and Outer Tube Handlebar Boss and Front Fork Handlebar and Handlebar Boss Engine Mounting: Front ; Rear — Upper ; Rear — Lower 1 Down Tube and Frame: Front 1 Rear l Footrest Bracket and Frame I Pivot Axle and Nut Relay Arm and Frame Connecting Rod and Swingarm Connecting Rod and Relay Arm Rear Shock Absorber and Reiay Arm Rear Shock Absorber and Frame Footrest and Footrest Bracket I Rear Footrest Bracket and Frame Rear Master Cylinder and Rear Arm Bracket Cowling and Stay Compression Bar and Brake Caliper Bracket Front Fork Pinch Bolt: Upper Lower Sprocket and Clutch Hub Brake Disc and Clutch Hub Inner Tube and Steering Stem Frame and Rear Frame: Upper

2003 Honda ST1300/A Wire Harness Inspection and Repair Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
REPAIR PROCEDURE Note: While completing this procedure DO NOT disconnect the 2-pin connector unless repair of the wire harness is required. 1. If not previously done, complete the ST1300/A #1 Service Bulletin before starting this procedure. 2. Remove the seats, left saddlebag, and left side panel by following the instructions in section 2 of the Service /l/Ianua/on pages 2-5 and 2-6. 3. Secure the centerstand assist handle out of the way. 4. Remove the rear shock adjuster support bar top bolt and move the bar out of the way. 5. Locate the ignition cord leading to the 2P connector and check the two black and white wires for chafing. |GNlTl6N con BLACK AND WHITE WIRES Chafing V I may OOCUF _ in this area 2-PIN CONNECTOR 2of6 – If the insulation is still intact and copper wire is not showing, proceed to the Preventative Measure section of this bulletin. – lf copper wire is showig, wrap the exposed area of the wire with a good quality electrical tape and proceed to the Preventative Mea- sure section of this bulletin. Preventative Measure: 1. Place the length of PVC split tubing around the ignition cord, butting up against the con- nector. Rotate the split toward the inside of the motorcycle. 2. Use good quality electrical tape to cinch the end of the PVC split tubing together (at the end that is touching the 2-pin connector), together. Secure the PVC split tubing to the ignition cord at the other end with electrical tape. 3. Secure the ignition cord and wire harness cord to the rear sub-frame with a commer- cially available wire band. The 2-pin connector should be routed behind and to the rear of where the rear shock adjuster support bar is located. ~! IR ARNESS C R COR W EH O D

Incoming search terms:

Sherco Engine Engine Removal and Case Splitting Manual

0

Filed Under (Sherco) by admin on 20-04-2011

download
Engine Removal and Case Splitting Preparation 1. Wash the bike and engine thoroughly. 2. Drain transmission oil by removing drain bolt and copper washer with 5mm Allen. 3. Drain coolant by removing 3 bolts of water pump cover and lifting off engine side case.4. Remove: a. rear fender- two bolts plus one long with washer using 4mm Allen b. fuel tank hose from petcock c. fuel tank- one short bolt and washer using 4mm Allen d. chain master link and chain from front sprocket e. kick starter- one large button head bolt and washer f. rear brake- one bolt/washer using 13mm wrench g. rear brake master cylinder- 2 button head bolts h. gear shifter- one bolt i. flywheel cover – 3 bolts j. clutch slave cylinder- two button head bolts using 4mm Allen k. clutch actuating rod by pulling it out of the case l. airbox three 4mm Allen bolts and loosening Phillips head carb hose clamp m. carburetor cap/slide assembly n. carburetor by loosening Phillips head manifold hose clamp o. spark plug cap p. spark plug q. header pipe 2 bolts into cylinder head r. silencer- 3 bolts (one with washer and nut using 10mm wrench) s. cylinder head coolant hose clamp and hose t. rear shock upper bolt u. radiator plastic cover bolt, then lever up the radiator with screwdriver until the radiator “legs” pop out of frame retaining holes 5. Remove flywheel using flywheel puller tool, taking care not to lose the small Woodruff
key by placing it inside of the magnetic flywheel for safe storage. 6. Remove ignition (3 bolts) and slide rubber grommet and ignition wiring assembly out of the case and out of the way, taking special note of the ignition timing marks. 7. Remove front sprocket and 2 retaining circlips. 8. Remove clutch side case and its 10 bolts using 5mm Allen, being careful not to lose to lose the 2 aluminum alignment pins (dowel pins). Insert the dowel pins into their holes within the Right Crankcase

HARLEY DAVIDSON LOW REAR SHOCK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
See Figure 3 and Table 1. INSTALLATION Shock Absorbers Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) Installation of any accessory suspension components can affect cornering clearance. This could distract the rider, causing loss of control and death or serious injury. (00431b) NOTES This procedure requires that both shocks be removed prior to installing the new shock absorbers. You need to place the motorcycle on a center stand with the rear wheel raised off of the ground. The jiffy stand should be able to move through its full range of travel. The exhaust system may interfere when removing and installing the lower right shock mounting hardware. If necessary, see Service Manual and remove the rear exhaust pipe. 2 4 5 7 1 6 3 is05206 1. Lower screw 2. Upper screw 3. Lower washer 4. Upper washer 5. Cover 6. Nut 7. Shock absorber Figure 1. Remove / Install Shock Absorber 1. Block the motorcycle under the frame so that the motorcycle is securely resting upright, the jiffystand may be moved through its full range of travel, and rear wheel is just off the ground. 2. Remove the lower shock mounting screw (1), washer (3) and nut (6) from the shock absorber (7). Save the hardware for reuse. 3. Remove the upper bolt (2), washer (4) and cover (5) and remove the shock absorber. Save the hardware for reuse. 4. Repeat Steps 1 and 2 for opposite side and save the hardware. 5. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the lower mounting bolt, then install bolt, lower washer and nut to the shock. 6. Apply 2-3 drops of LOCTITE 243® (blue) on the threads of the upper mounting bolt, then install the shock cover, upper mounting bolt and washer to the shock. Verify the cutout in shock cover locates properly

Incoming search terms:

Honda Goldwing GL1800 Independent Rear Suspension Trike Conversion Installation Guide

0

Filed Under (Honda) by admin on 17-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame

Honda Goldwing GL1800 Independent Rear Suspension Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. □ Seat (to be re-installed without modification) □ Left and right side covers (to be re-installed without modification) □ Battery and battery box (to be re-installed without modification) □ Left and right saddle bags □ Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) □ Trunk (to be re-installed without modification) □ Left and right passenger foot rests (to be re-installed without modification) □ Left and right foot rest under covers (to be modified and re-installed) □ Left and right rear crash bars □ Saddle bag trunk stay (to be modified and re-installed) □ Left and right mufflers (Mufflers only, do not remove decorative covers) . Retain OEM muffler rubber mounting bushings and flanged spacers for re-installation of the mufflers. □ Rear wheel □ Left and right pivot bolt covers (to be re-installed without modification) □ Reverse resistor (to be relocated) □ Swing Arm and Driveshaft IMPORTANT : Carry out brake system modifications (See Section 5) prior to removing Swing Arm. Evacuating all the brake fluid from the system will prevent brake fluid spills when the OEM swing arm is removed. Note : Upper bolt of mono shock can be removed without removing the fuel tank. □ Rear Shock and Hydraulics. Unscrew angle sensor from OEM shock and secure to frame with cable tie. □ Shock arm and shock link Note : You may need to cut out the bolt that attaches the shock link to the frame Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm . 5.1 Explanation of OEM brake system and changes From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Trike Conversion Kit.

HARLEY DAVIDSON CHROME UPPER BELT GUARD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION NOTE When performing the following step, it is not necessary to completely remove the shock mount bolt, back the bolt out only until it is flush with the swingarm. 1. See Figure 1. Loosen the left rear shock mount bolt (1) and back it out until the threaded portion of the bolt is flush with the swingarm. 1 2 is03762 1. Shock mounting bolt (left side) 2. Belt guard Figure 1. Loosen Shock Mounting Bolt 2. Pull the belt guard (2) straight back toward the rear of the bike to remove the guard from upper and lower grommets. See Figure 2. It may be necessary to work the guard up and down slightly to dislodge it from the upper (1) and lower (2) grommets. Remove the belt guard and discard. 2 1 3 is03763 1. Upper grommet mount 2. Lower grommet mount 3. Front belt cover Figure 2. Rubber Grommet Mount Locations 3. Obtain the chrome belt guard from kit. While making sure belt guard is over the belt, slide the guard straight in between the shock and sprocket and align cover just below front belt cover (3). The cutouts in the bracket should be lined up to engage with upper and lower grommets. NOTE When performing the following step, gently pull the guard in and out at the center; it should feel fairly tight even though the rear mounting bracket has not been secured. 4. See Figure 3. Firmly push the guard toward the front of the bike until the cutouts are secured by the grommets and the belt guard mounting bracket (1) hole lines up with the shock bolt

Incoming search terms: