HARLEY DAVIDSON BOOM! AUDIO BASS BOOSTER TOUR-PAK PORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
PREPARATION NOTE For vehicles equipped with security siren: • Verify that the Hands-Free Fob is present. • Turn the ignition key switch to IGNITION. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the owner’s manual and follow the instructions to remove the main fuse. INSTALLATION NOTE The Tour-Pak does not need to be removed from the vehicle to perform this installation. 1. Open the Tour-Pak lid and remove all items from the Tour- Pak base. 2. Models equipped with mat: Remove the mat. Models equipped with liner: Open the map pocket, and remove the acorn nuts with flat washers. Remove the map pocket and liner. 3. Remove four screws from the left-side speaker grille on the Tour-Pak. Remove the speaker grille from the speaker pod. 4. Remove the speaker from the speaker pod. Carefully pull the two socket terminals from the speaker spade contacts. 5. Remove the grommet, and draw the rear speaker/passenger controls connector out of the speaker pod. Separate the connector halves. 6. Repeat Steps 3 through 5 for the right-side speaker. 7. See Figure 1. Get the drill template (3) from the kit. If NOT equipped with power port: a. Remove one speaker pod mounting screw and flat washer. b. Align the drill template on the inside of the Tour-Pak with the speaker pod holes, and hold in place with the mounting screw and washer. c. Repeat for the remaining template mounting holes. If equipped with power port: a. Remove the two screws and flat washers to free the power port from the Tour-Pak. b. Align the drill template on the inside of the Tour-Pak with the power port holes, and hold in place with the mounting screws and washers. c. Repeat with the top speaker pod mounting screw and flat washer. NOTE Tighten the screws enough to hold the speaker pod in place as the pilot hole is drilled. 8. Where indicated on the template, drill a 3/16 inch (5 mm) diameter pilot hole through the Tour-Pak wall and speaker pod. 9. Remove the screws and speaker pod, and set aside. Turn the template over, and repeat Steps 7 and 8 on the left side of the Tour-Pak. NOTE Hole size will affect the fitment of the ports. The hole saw needs to be sharp. 10. Carefully drill a two inch (51 mm) diameter hole with a sharp hole saw, at the pilot location, through each speaker pod and in both locations on the Tour-Pak wall. 11. Temporarily install the Tour-Pak liner (if equipped), and mark the location of the two inch (51 mm) diameter holes on the outside of the liner. Remove the liner, and carefully cut the two holes in the liner front wall

Incoming search terms:

HARLEY DAVIDSON ADVANCED AUDIO REAR SPEAKER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
This kit fits 2006 and later FLHT (Electra Glide®), FLHTC (Electra Glide Classic), FLHX (Street GlideTM) and FLTR (Road Glide®) model motorcycles. INSTALLATION 1. Have a Harley-Davidson dealer perform the speaker software flash to the previously installed AM/ FM/ CD Radio. 2. Refer to the Service Manual and follow the instructions given to remove the seat and the left-side saddlebag. The right-side saddlebag does not need to be removed, but you may choose to do so in order to prevent damage during the installation of this kit. 3. Follow the instructions in the Service Manual to remove the maxi-fuse. NOTE The Tour-Pak does not have to be removed from the vehicle to perform this installation. 4. Open the Tour-Pak lid and remove all items from the Tour- Pak base. 5. Models with rubber mat: Remove the mat. Models with molded liner: Open the map pocket and remove the acorn nuts with flat washers. Remove the map pocket and liner. 6. Obtain the left-side (3) and right-side (4) drilling templates from the kit. is 00439 Figure 1. Template Positioning (Right Side Shown) 7. See Figure 1. Position the the right-side template flat onto the right front corner of the Tour-Pak. a. Fit the notched corner on the left side of the template to the Tour-Pak latch. b. Align the top of the template just under the top edge of the Tour-Pak. c. Apply tape to the locations indicated on the template to hold the template in place

Incoming search terms: