HARLEY DAVIDSON CHROME PASSENGER FOOTBOARD SUPPORT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
Removing Passenger Footpegs 1. Remove and discard the socket screw and lock washer attaching the existing footpeg bracket to the rear swing arm bracket. Proceed to Step 5. Removing Passenger Footboard Supports 1. For standard footboard 50613-91: See the Service Parts illustration. Tilt the footboard to the “up” position. Remove the underside chrome footboard covers if so equipped. From the bottom of the footboard, use a small flat-blade screwdriver to push the rubber beads on the pad up through the holes in the footboard pan. Remove the pad. For swept-wing (FLHRS- and FLHTCSE-style) footboards: With the passenger footboard in the “down” position, carefully raise an outside “corner” of the stock footboard insert off the footboard pan with a suitable flat-bladed tool, taking care to avoid scratching the chrome footboard pan. Continue around the edge of the footboard, using a second flat-bladed tool if necessary to pry up and remove the old insert. 2. Using a brass drift and rubber mallet, tap one pivot pin (6) out of the pivot hole into the center pocket of the footboard pan, remove the pin and set it aside. Repeat for the second pin. 3. Remove the footboard from the support bracket (1). Remove and discard the steel ball (5) and spring (4) from the hole in the bracket. 4. Remove and discard the socket head screw (2) and lock washer (3) attaching the footboard support bracket to the rear swing arm bracket. Proceed to Step 5. Installing the New Footboard Supports NOTE Three holes are available in the rear fork brackets for footboard support mounting. Depending on model and year, the footboards can be installed in any of two or three positions for passenger comfort. A plastic plug, inserted in the upper hole at the factory, can be removed. 5. See the Service Parts illustration. Position a new chrome footboard support (1) against the swing arm bracket at the desired height. The left and right supports are identical. With the locating peg on the footboard support in the next lower hole, fasten the support with a hex socket screw (2) and lockwasher (3) from the kit. Tighten the screw to 15-18 ft-lbs (20-24 Nm). 6. Place the new spring (4) into the retaining hole in the footboard support. Rest the detent ball (5) on top of the spring

MACHINE SPECIFICATION FOR 115cc (UNDERBONE) (4-stroke horizontal layout engine)

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
(This is for clarification only. Other parts not listed in Art. 2.5 & 2.6 can be altered or replaced. Change of specification means modification, changes or removal of the parts.) 2.6.1 Change of compression ratio is allowed. 2.6.2 Setting of carburetor, attachment or size change of air funnel. 2.6.3 Inlet opening of fuel tank for fuel charge may be modified but cannot be relocated. 2.6.4 Change of fuel pipe and fuel cork. 2.6.5 Change of exhaust pipe and muffler, but must have silencer. 2.6.6 Material of clutch discs and specifications of spring. Hand clutch is allowed. 2.6.7 Gear ratios are free. 2.6.8 Starting device and parts relative to this device may be removed. 2.6.9 Modification or removal of air cleaner box, wire harness and control wires. 2.6.10 Removal of speedometer (including meter gearbox and cable.) 2.6.11 Removal of drive chain case and cover. Change of drive chain is allowed. 2.6.12 Change of final gear ratio is allowed. 2.6.13 Attachment of bead stopper and balance weight to tyre. 2.6.14 Modification and change of rear brake part is allowed. 2.6.15 Frame body may be strengthened. 2.6.16 Modification and change to brackets and pedals including footrest. 2.6.17 Front suspension unit must remain as originally produced by the manufacturer. However, the following internal parts of the fork can be modified: Shims, hydraulic piston, oil passages, springs and spacers. 2.6.18 Attachment of stabilizer to strengthen or reinforcing rear swing arm is allowed. 2.6.19 Removal of dust seals. 2.6.20 Rear suspension unit must remain as originally produced by the manufacturer. However rear suspension unit is free. The rear linkage must remain as originally produced by the manufacturer. 2.6.21 Handle bars, clutch and front brake lever may be changed by an after market copy. Clutch springs may be changed. 2.6.22 Steering dampers may be fitted. They must not act in any way as a steering lock limiting device. 2.6.23 Materials of streamlining and material of seat cowling. (However, expensive materials such as carbon fibre and kevlar are not allowed). 2.6.24 Removal of rear mudguard and side cover. Front mudguard may be cut but not less than 6 inches from the front fork on original part. 2.6.25 All lubricants are free 2.6.26 Adjusting and polishing any parts are allowed. Adjusting is defined as : “To select each part or assembly complete with-in the limit of single or total tolerance” (i.e. that of valve clearance, ignition timing etc.) 2.6.27 Cutting unnecessary stays is