HARLEY DAVIDSON XL DETACHABLE SOLO RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
Kit Contents See Figure 2 and Table 1. There are no Service Parts available with this kit. INSTALLATION 1. See Figure 2. While standing behind the motorcycle, place the front rack notches (1) into the front docking points (2). NOTE Check alignment as shown in Figure 1. Failure to properly align the docking points and sideplates may result in damage to the rear docking points. 2. Pull the rotary latches (3) back into their rearmost position. Position the rear rotary latches over the rear docking points (6), ensuring the latches and sideplates (4) fit into the neck (5) of the rear docking points. This may require some gentle squeezing or spreading of the sideplates. NOTE The front and rear docking points must be fully engaged. If docking points are not fully engaged or docking kit is loose, it could shift position or come loose during operation. 3. Push down and close the rotary latches by pressing the latch lever (7) as far forward as it will go. You will hear a click when the latch is in place. If the latch does not easily close, do not force. Recheck alignment as described in Step 2. 4 4 3 2 2 1 1 1 2 is 00963 1. Right sideplate 2. Right front docking point 3. Correct: sideplate fully engaged in docking point 4. Incorrect: sideplate NOT fully engaged in docking point Figure 1. Sideplate Must Fit into Docking Point Correctly REMOVAL 1. See Figure 2. To remove the rack, press the release button (8), and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points

HARLEY DAVIDSON FLHR 2-UP RACK REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INST ALLATION/REMOVAL 1. See Figure 1. While standing behind the motorcycle, place the front rack notches (1) into the front docking points (2). (Most of the rack, except a typical sideplate, has been removed for illustration purposes). 4 4 1 3 2 5 3 6 7 is03799 1. Front rack notches 2. Front docking points 3. Rotary latches 4. Rear docking points 5. Sideplates 6. Neck 7. Release button Figure 1. Attaching 2-Up Rack NOTE Rear docking points may be damaged if rotary latches and sideplates are not properly aligned. If the latch does not easily close, do not force. Check alignment as described in Step 2. 2. Pull the rotary latches (3) back into their rearmost position. Position the rear rotary latches over the rear docking points (4), making certain the latches and sideplates (5) fit into the neck (6) of the rear docking points. This may require some gentle squeezing or spreading of the sideplates or docking point brackets. 3. Push downward and close the rotary latches by pressing the latch lever as far forward as it will go. You will hear a click when the latch is in place. If the latch does not easily close, do not force. Recheck alignment as described in Step 2. 4. To remove the rack, press the release button (7), and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points

HARLEY DAVIDSON ONE-PIECE DETACHABLE SISSY BAR UPRIGHT AND PAD KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
INSTALLATION Passenger Upright Installation 1. See Figure 1. Stand behind the motorcycle, and place (10) the front upright notches (2) into the front docking points (3). 2. See Figure 2. Check for correct notch engagement. NOTE Failure to correctly engage the sideplate notches to the docking points may result in damage to the rear docking points. 3. See Figure 1. Pull (11) the rotary latches (4) back into their rearmost position. Align the latches over the rear docking points (7), making sure the latches and rear notches (6) fit into the neck (8) of the rear docking points. NOTE This may require some gentle squeezing or spreading of the upright sideplates. 4. Push downward (12) on the sideplates, and close the rotary latches by pressing (13) the latch lever as far forward as it will go. A click will be heard when the latch is in place. If the latch does not close, do not force it. 13 4 1 5 2 9 3 7 10 7 8 5 4 6 11 12 is00058 1. Passenger upright 2. Front notch 3. Docking point, front 4. Rotary latch 5. Release button 6. Rear notch 7. Docking point, rear 8. Rear docking point neck 9. Fender support bracket 10. Place front notches into front docking points. 11. Pull latches back. 12. Lower rear notches onto rear docking points. 13. Push forward to close latches. Figure 1. Detachable Passenger Upright

HARLEY DAVIDSON Detachable Solo Racks removal and Installation instructions

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
installation/Removal 1. While standing behind the motorcycle, place the front rack notches into the front docking points as shown in step 1 of the diagram. (Most of the rack, except a typical sideplate, has been removed for illustration purposes). 1 CAUTION Rear docking points may be damaged if rotary latches and sideplates are not properly aligned. If the latch does not easily close, do not force. Check alignment as described in step 2. 2. Pull the rotary latches back into their rearmost position as shown in step 2 of the diagram. 3. Push downward and close the rotary latches by pressing the latch lever as far forward as it will go as shown in step 3. You will hear a click when the latch is in place. If the latch does not easily close, do not force . Recheck alignment as described in step 2. 4. To remove the rack, press the release button shown in the diagram, and pull the rotary latch lever back. Carefully lift the rear of the rack up and pull the rack out of the front docking points. Position the rear rotary latches over the rear docking points, making certain the latches and sideplates fit into the neck of the rear docking points as shown in the rear view of step 2. This may require some gentle squeezing or spreading of the sideplates. Attaching Solo Rack INSTRUCTIONS -J00256 REV. 8-30-96 Detachable Solo Racks ® i00627 Step 1:place front notches into front docking points Step 2: pull back rotary latches and lower rack onto rear docking points Step 3: close rotary latches by pushing latch fully forward Release button

BUELL XB9R REMOVABLE SADDLEBAG KIT Installation Instructions

0

Filed Under (Buell) by admin on 03-02-2011

download
Installation 1. Ensure that the tail section of the motorcycle is clean and dirt free. 2. See the Service Parts illustration. Using a T27 TORX drive head, remove the two screws holding the tail section underside shield. 3. Install the saddlebag bracket (3) as shown, reinstall the screws and tighten securely. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. The mounted saddlebags will cover the factory-installed rear side reflectors on these vehicles. Reposition, or have a dealer reposition, the original rear side reflectors supplied with this motorcycle or apply new ones. If this is not done, the loss of visibility to other motorists may result in death or serious injury. NOTE New reflectors (Part number 59256-84A) are available from your Buell Dealer. NOTE When removing adhesive residue, take care to keep from scratching or damaging the reflector, mounting bracket or surrounding parts. 4. Use a thin flat blade, like that on an X-Acto knife, and carefully pry the reflectors off of their mounting brackets. Remove the adhesive residue from the brackets and the back of the reflector. 5. Mount the new reflector relocation brackets (4) to the stock reflector mounting brackets as shown. Attach each relocation bracket through the slots in the stock bracket with two screws, flat washers and lock nuts from the Hardware Kit (5). Slide the relocation bracket to the rearmost position and tighten securely. 6. Remove the outer release liner of the foam tape on the relocation bracket. Mount the stock reflector squarely to the bracket, and press firmly in place. 7. Remove the passenger pillion (and pillion cover, if mounted), and set aside. 8. Position one of the saddlebags to the side of the motorcycle tail section with the Buell logo facing out, and to the rear. Hook the mounting pocket on the back side of the bag onto the saddlebag bracket mounted earlier. Repeat for the other saddlebag. 9. Bring the saddlebag straps up and over the tail sectiion. Pull the right-side straps up through the buckle eyes on the left-side straps, remove any slack and fasten the hook-and-loop material. 10. Note the points where the saddlebags and straps contact the motorcycle tail section. Two lengths of clear protective tape have been provided in the Hardware Kit. If desired, cut and fit lengths of the tape to those areas of the tail section to prevent damaging the finish. 11. Replace the passenger pillion (and pillion cover if desired). Position the front tongue on the pillion overthe saddlebag straps