Harley Davidson 39 mm Front Spring Lowering Kit INSTALLATION PROCEDURE

0

Filed Under (Harley Davidson) by admin on 07-04-2012

download
1. Support the motorcycle so the front wheel is off the ground. Next remove the front wheel and fender. Remove the fork cap nuts and loosen the lower triple clamp pinch bolts. Remove the front brake caliper. Some models have a tapered end to the fork tube. Extra effort will be required to remove the tube from the crown. Loosen the top fork cap 1 to 2 revolutions. Use a soft wood block or similar tool (that will not mark fork cap finish) and tap down with mallet to loosen fork tube from its tapered fit in top steering crown. Make sure fork pinch bolts are loose. To completely remove fork of this style, unscrew the fork cap entirely. 2. Slide both fork assemblies out of the triple clamps. Unscrew the top fork tube plugs. Remove the plugs and fork springs. CAUTION: Fork caps are under spring pressure and could cause serious injury. Drain the fork oil by turning the fork assemblys upside-down. 3. Next, bottom the fork tube into the fork leg. DO NOT extend the tube while you remove the allen bolt on the bottom of the fork leg. Turn the assembly upside-down and shake the damper rod and rebound spring out of the fork assembly. Again, DO NOT extend the tube during this. Extending the tube could dislodge the internal bottoming cone, which fits on the end of the damping rod, making it very difficult to reinstall the damper rod without complete fork disassembly. 4. FOR 1″ REDUCTION IN FORK LENGTH: You must first measure the length of the O.E.M. rebound spring. Depending on the model of the motorcycle, the length will either be 1″ or 2″ long. A. If you currently have a 1″ rebound spring, you need to replace it with the 2″ long LA Choppers rebound spring (included in the kit), then reinstall the damper rod in the fork tube. B. If you currently have a 2″ rebound spring, you will need to add the 1″ long spacer, then reinstall the damper rod in the fork tube.

YAMAHA WR450F (S) 2-TRAC SPECIFICATIONS/ SUPPLEMENTARY OWNER’S SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING DIAGRAM STEERING DAMPER ADJUSTMENT 19 Damping sweep controls Damping sweep ontrols 5 are located on each side off the damper body. Damping is in position 2, (12 o´clock), when delivered from Yamaha. This setting is fitted for enduro, motocross and off-road riding. WARNING Always ensure that valve setting is within the permitted ranges. NOTE: Both damping sweep controls must always be set in identical positions. Always use positions according to the clock. Suitable starting position: Motocross pos. 1 or 2 Enduro pos. 2 or 3 Off-Road pos. 2, 3 or 4 Technical data External measures 70x70x35 mm Seals Low friction type Oil Öhlins part no. 01306-01 Maintenance and inspection The steering damper is a precision instrument, with extremely fine tolerances. It is therefore essential that it is maintained in a correct manner. Maintenance and service should be carried out by an authorised service center. NOTE: After washing the motorcycle wipe clean and spray with all-round oil. Never subject to direct high-pressure cleaning since water may otherwise penetrate the damper. Ensure that there is no leakage of fluid and that there is no visible damage to the housing and mounts FRONT FORK REBOUND DAMPING FORCE ADJUSTMENT The rebound adjuster is located at the top of the fork leg. 1. Adjust: • Rebound damping force By turning the adjuster. Stiffer → Increase the rebound damping force. (Turn the adjuster in.) Softer → Decrease the rebound damping force. (Turn the adjuster out.) Extent of adjustment: Maximum Minimum Fully turned in 20 clicks out position (from maximum position) • STANDARD POSITION This is the position which is back by the specific number of clicks from the fully turned-in position. Standard position: 14 clicks out Do not force the adjuster past the minimum  or maximum extent of adjustment. The adjuster may be damaged. WARNING Always adjust each front fork to the same set- ting. Uneven adjustment can cause poor handling and loss of stability

Incoming search terms:

SUZUKI SV1000/ S SERVICE MANUAL Supplimentary

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CHASSIS BOLT AND NUT Check that all chassis bolts and nuts are tightened to their specified torque. (Refer to below and page 2-29 of SV1000S Service manual for the locations of the following nuts and bolts on the motorcycle.) CHASSIS FRONT FORK REMOUNTING Align the upper surface A of the inner tube with the upper surface B of the steering stem upper bracket. Tighten initially at 1 000 km (600 miles, 1 month) and every 6 000 km (4 000 miles, 6 months) thereafter. ITEM N·m kgf-m lb-ft 1 Handlebar clamp bolt 23 2.3 16.5 2 Handlebar holder set nut 45 4.5 32.5 SV1000K3 5 SUSPENSION SETTING After installing the front fork, adjust the spring pre-load and damping force as follows. SPRING PRE-LOAD ADJUSTMENT There are eight grooves on the spring adjuster. Position 1 provides the maximum spring pre-load and position 8 provides the minimum spring pre-load. STD position: 7 DAMPING FORCE ADJUSTMENT Rebound damping force Fully turn the damping force adjuster 1 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 and 1/4 turns out from stiffest position Compression damping force Fully turn the damping force adjuster 2 clockwise. It is at stiffest position and turn it out to standard setting position. STD position: 1 turn out from stiffest position STANDARD FRONT SUSPENSION SETTING ! FRONT Spring pre-load adjuster Damping force adjuster Rebound Compression Solo and dual riding 7 1 and 1/4 turns out from stiffest position 1 turn out from stiffest position Be sure to adjust the spring pre-load and damping force on both front fork legs equally. 6 SV1000K3 HANDLEBARS REMOVAL AND DISASSEMBLY Remove the handlebar balancer 1. NOTE: Do not remove the handlebar balancer mounting screw before removing the handlebar balancer. Slightly loosen the mounting screw, and then pull the balancer assembly out of handlebars. Remove the rear view mirror 2. Disconnect the front brake light switch coupler 3. Remove the front brake master cylinder. Remove the right handlebar switch 4 and throttle grip 5. Disconnect the clutch switch lead wires 6. Remove the left handlebar switch 7. Remove the rear view mirror 8. Remove the clutch master cylinder. Remove the handlebar clamp caps

Incoming search terms:

2005-2007 KTM 5018 DCC 5018 SXS 5018 SMR WP SHOCK ABSORBER REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
liter fuel consumption is equivalent to approx. 15 operating hours Check the bearing in the shock absorber top / replace if necessary Check the piston rod on scratches / leakage Check the static sag – before riding Check the spring Check the bump rubber Check the O-ring of the spring retainer / replace if necessary Complete maintenance of the shock absorber 10 hours 65 liter 20 hours 130 liter 30 hours 200 liter 40 hours 260 liter 50 hours 325 liter 60 hours 400 liter 70 hours 455 liter 80 hours 520 liter 90 hours 600 liter 100 hours 665 liter Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut. Recommended periodic maintenance and inspection of the 5018 SXS/SMR Shock absorber

Incoming search terms:

KTM 125/ 200/ 250/ 300 SX, MXC, EXC SERVICE MANUAL

0

Filed Under (KTM) by admin on 28-11-2010

download
Compression damping of shock absorber (MXC, EXC) The compression damping (during compression) can be adjusted for the MXC and EXC shock absorbers (Mono Compression Control). The degree of damping can be adjusted by turning adjusting screw 1 with a screwdriver. Turning in a clockwise direction will increase the damping, turning in a counterclockwise direction will decrease the damping. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X757…………..17 clicks Type White Power 1218X759…………..17 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . NEVER TRY TO TAKE THE SHOCK ABSORBER APART OR TO DO ANY MAINTEN – ANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 2 CONNECTION (24 MM ). Rebound damping of shock absorber (SX, MXC, EXC) By using the adjusting screw 3 , the degree of damping of the rebound can be adjusted. Turn the knob to the right side to increase damping, turn it to the left side to reduce damping during rebounding. STANDARD ADJUSTMENT: -Turn the adjusting screw clockwise to the stop. -Then turn the adjusting screw counterclockwise, counting the number of clicks that corresponds to the respective type of shock absorber. Type White Power 1218X756…………..28 clicks Type White Power 1218X757…………..28 clicks Type White Power 1218X759…………..26 clicks * WARNING * THE DAMPING UNIT OF THE SHOCK ABSORBER IS FILLED WITH HIGH – COMPRESSION NITROGEN . N EVERTRYTOTAKETHESHOCKABSORBERAPARTORTODOANYMAINTE – NANCE WORK YOURSELF . SEVERE INJURIES COULD BE THE RESULT . NEVER UNSCREW THE BLACK SCREW 4 CONNECTION (15 MM )

Incoming search terms: