1999-2010 Yamaha Roadstar 465 Series Single Shock Supplement

0

Filed Under (Yamaha) by admin on 14-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n Remove the horn located on the lower left side. Also remove the Remote Adjustable Pre-Load adjuster knob by removing the screw located in the center of the knob, then pull it straight off. n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the opening behind where the horn was located on the left side of the bike – see figures 2 and 3. Do not loosen or attempt to rotate the line between the shock and the adjuster. n Reinstall the adjuster knob, and torque the screw to 50 in/lbs. (5.65 N-m). n Make sure the shock rebound adjustment is at the rear facing the left side of the motorcycle and the pressure valve is facing up. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the stock two drive-belt cover bolts – as shown in figure 4. n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. Reinstall horn. To adjust the ride height, simply turn the adjuster knob clockwise (looking at it from the back of the bike) to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride height

BMW F650GS Single Shock Supplement

0

Filed Under (BMW) by admin on 14-02-2011

download
Mount the shock & adjuster as you would your stock shock & adjuster per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the same path as the stock line was routed to the same location. n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is facing the right side of the motorcycle and the pressure valve is facing forward. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m) as in figure 3. Then mount the bracket and adjuster to the bike in the same location as the stock preload adjuster/bracket using the stock bolts as shown in figure 4. Check banjo-bolt to cylinder clearance and adjust if necessary via tolerances in mounting bracket holes. n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. To adjust the ride height, simply turn the adjuster knob clockwise to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride height.

Suzuki GSX1000R 465 SeriesSingle Shock Supplement

0

Filed Under (Suzuki) by admin on 13-02-2011

download
1. One set of the shouldered sleeves with O-rings should be installed in the shock eye. If not, insert sleeves with O-rings in the shock eye (see figure 1). 2. Mount the shock as you would your stock shock per your authorized shop manual noting the following; Make sure the shock is mounted with the rebound adjustment at the bottom and facing the right side of the motorcycle and the nitrogen pressure valve is facing forward. Tighten the shock bolts to the proper torque specifications (refer to your manual). Caution: The installed spring length must never be set shorter than 133mm (5.25″) or shock damage may occur

Suzuki VZR1800 465 Series Single Shock Supplement

0

Filed Under (Suzuki) by admin on 13-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n On the left side of the motorcycle, remove the secondary drive cover, rectifier cover, and rectifier. Also remove the Remote Adjustable Pre-Load adjuster knob by removing the screw located in the center of the knob, then pull it straight off. n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster (knob removed) through opening between the frame and the rear of the motor – just behind & below where the shift-shaft comes out – on the left side of the bike (see figure 3 & 4) . Do not loosen or attempt to rotate the line between the shock and the adjuster. n Reinstall the adjuster knob, and torque the screw to 50 in/lbs (5.65 N-m). n Make sure the shock rebound adjustment is towards the rear and facing down and the pressure valve is towards the front facing up. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the two lower mounting bolt holes for the rectifier bracket as shown in figure 5 – one of which is the lower mounting bolt for the rectifier, which will be replaced with the supplied longer fastener. Reinstall the rectifier, sandwiching the adjuster bracket behind it (see figure 6) . n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. n Reinstall the secondary drive cover and rectifier cover (figure 7) , then proceed to adjust your ride height.

Yamaha XV-19 Raider 465 Series Single Shock Supplement

0

Filed Under (Yamaha) by admin on 13-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster towards the rear (see figure 2) and to the right side of the swingarm (see figure 3) . n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is toward the rear and facing the right side of the motorcycle and the nitrogen pressure valve is facing down. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Locate the EXUP valve servo mounting bracket, specifically the two bolts used to secure it to the frame (see figure 4) . They below the seat on the right hand side of the motorcycle. n Now either mount the adjuster to the supplied mounting bracket using the supplied M6-1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m), then mount the bracket and adjuster to the bike using two EXUP valve servo mounting bolts (as shown in figure 5) – or – mount the adjuster bracket to the frame using those two bolts, then mount the adjuster to the bracket (may require removal of exhaust stay). n Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources.

Incoming search terms:

Kawasaki KLR-650 465 Series Single Shock Supplement

0

Filed Under (Kawasaki) by admin on 13-02-2011

download
Mount the shock as you would your stock shock per your authorized shop manual (with the rebound adjustment at the bottom) noting the following: n As you mount the shock, feed the Remote Adjustable Pre-Load adjuster through the opening between the main-frame and sub-frame on the left side of the bike. n Do not loosen or attempt to rotate the line between the shock and the adjuster. n Make sure the shock rebound adjustment is facing the right side of the motorcycle and the pressure valve is facing forward. n On 1987-2007 models ONLY , install the supplied 3.5mm thick spacers – one on each side of the shock clevis ( see figure 3 ). Do not install these spacers on 2008-2010 models. n Tighten shock bolts to the proper torque specifications (refer to your manual). n Mount the adjuster to the supplied mounting bracket using the supplied M6- 1.0X8mm SHCS fasteners and torque them to 80-90 in/lbs (9-10 N-m). Then mount the bracket to the bike using the two rear footrest mounting bolts – sandwiching the mounting bracket between the rear footrest mount and the frame tabs (as shown in figure 4) . Using the supplied zip-ties, secure the hydraulic line away from any moving parts or heat sources. n To adjust the ride height, simply turn the adjuster knob clockwise (looking at it from the back of the bike) to increase the height and counterclockwise to reduce it. See main instructions for procedure of achieving optimum ride heigh

KTM Preload Adjuster frontfork Disassembly And assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 5 Preload Adjuster Frontfork 03/2002 Screw the screw-cap to the right so that the spring washer is turning out of the screw-cap PA. Remove the spring washer. Pay attention to the assembling direction!!! Turn the plastic adjustment tube holder out of the screw-cap. 12_021 12_022 12_023Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 6 Preload Adjuster Frontfork 03/2002 1. Remove the O-ring inside. Unscrew the air release plug. 12_024 12_025 12_026 2. Remove the O-ring.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 7 Preload Adjuster Frontfork 03/2002 Disassemble the adjusting knob from the screw-cap. Pay attention to the steel balls and spring!!! 12_027 12_028 12_029 Heat the steel nut. Unscrew the nut (size 32) clockwise .Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 8 Preload Adjuster Frontfork 03/2002 The nut. Pay attention to the assembling direction!!! Remove the O-ring. 12_030 12_031 12_032 Push the holder rebound PA out of the screw-cap.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 9 Preload Adjuster Frontfork 03/2002 – springring – spring washer – O-rings – holder rebound adjustment tube – rebound adjusting knob with steel balls and spring – air release screw with O-ring – nut – holder rebound adjustment cpl. with O-ring – screw-cap PA

Incoming search terms:

KTM WP FORK 4860 MXMA CLOSED CARTRIDGE REPAIR MANUAL

0

Filed Under (KTM) by admin on 13-02-2011

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 22-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork

Incoming search terms:

2005-2007 KTM MOTORCYCLE REPAIR MANUAL

0

Filed Under (KTM) by admin on 21-11-2010

download
Adjustments -Take notice of the position of the compression adjustment 1 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -Remove the rubber cap out of the axleclamp. -Take notice of the position of the rebound adjustment 2 ! -Count the amount of clicks by turning the adjustment screw clockwise till fully closed. -For the standard position see setting list. Position of the compression and rebound adjustment -Set the rebound position 1 , see KTM-Owners manual. -Assemble the rubber cap. -Set the compression position 2 , see KTM-Owners manual. 1 2 2-22 Repair manual WP Fork “Closed Cartridge” Art.No.: 3.211.199-E Explanation of the spring preload -Total spring length without the spacers, see chapter inspection of the spring! -Spring length with spacers 1 , see setting list. -Spring with the spacers. 1 . -The spring is assembled in the front fork leg. NOTE: the distance of “B” is less then the length of “A”. A – B = Spring preload A 1 1 B 2-23 Air release screw -Place the motorcycle on the stand. NOTE: the front wheel must be lift of the floor! -Unscrew the air release screw 1 of the screw cap on top of the front fork and tighten after approx. 10 seconds the air release screw. Recommended periodic maintenance and inspection of the 4860 SX/SXS/SMR front fork 1 A 100 liter fuel consumption is equivalent to approx. 15 operating hours Clean dust scrapers (after 1 hour) Bleed fork legs regularly – after every cleaning Check the inner tubes on scratches / leakage Visual check of damaging of the outer-tubes / replace if necessary Complete service without disass. the closed cartridge of the fork Complete service including the closed cartridge of the front fork Dismounting the fork -Place your motorcycle on a stand. -Notice the position of the front fork in the triple-clamps. NOTE: To remove the front fork. Read your KTM Instruction Manual or Workshop Manual. 3-3 Mounting the fork -Clean the innerside of the triple-clamps with brake cleaner. -Slide both fork legs into the triple-clamps. NOTE: Pay attention to the position of the fork legs. Standard riding height! NOTE: The maximum riding height is the level of the second groove! -Tighten the middle bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the first bolt of the lower triple clamp to a torque of 17 Nm! -Tighten the third bolt of the lower triple clamp to a torque of 17 Nm!

Incoming search terms: