HARLEY DAVIDSON COMFORT PROFILE REAR SADDLEBAG GUARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2011

download
REMOVAL 1. Remove saddlebags from motorcycle following the instructions in the service manual. 2. See Figure 3. Remove grab strap screw and washer (G). Remove grab strap (H). Remove seat following the instructions in the service manual. 3. Remove left and right side covers (located in front of saddlebags) by removing screw from bottom of side cover. Save hardware and side covers for final assembly. 4. Support muffler assembly with a block of wood or other suitable method. For FLTR and FLHX Models 1. See Figure 3. Remove the screws (F) securing saddlebag guards to muffler supports. 2. Remove bolt (M) and nut (P). Save bolt (M) for installation. Discard nut (P). 3. Remove screws (B and C) and nut (E). Save screws (B and C) for installation. Discard nut (E). 4. Remove stud receptacle (I) and save for installation. 5. See Figure 1. Remove antenna bracket (1), mounting fasteners (2), antenna mounting nut (5), washer (4) and antenna adapter (3). Save the antenna and hardware, discard the bracket. 6. Remove support (D) and discard. 7. Repeat Steps 1 through 4 for other side. For FLHTCU and FLHTC Models 1. Remove and discard screws (X) and guard rail mounts (W and V). 2. Remove screw (Q) and rear guards (U). Discard rear guard assembly including screws (T) and clamps (R and S). Discard screw (Q). 3. Remove and discard screw (K) and nut (L). 4. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E), screw (N) and forward guard. 5. Repeat Steps 1 through 5 for other side. For All Other Models 1. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E) and screw (N). 2. Remove and discard screw (K) and nut (L). 3. Remove forward guard and discard. 4. Repeat for other side

HARLEY DAVIDSON SIGNATURE SERIES SOLO SEAT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL NOTE Refer to owner’s manual or service manual for seat removal instructions for your model. 1. Remove right and left saddlebags according to the instructions in the service manual. Save saddlebag mounting brackets and hardware. 2. Remove passenger seat strap. Discard passenger seat strap. 3. Remove existing seat from vehicle. 4. See Figure 1. Remove and discard stock nuts (2) from studs (1) on rear fender (3). INSTALLATION Install Rider Seat 1. Push front seat on frame with mounting bracket at rear. 2. Firmly push front of seat downward and rearward until frame tongue engages slot in seat. 3. Push seat forward until studs are centered in slots of mounting bracket. 4. See Figure 4. Install two nuts (4) on studs to secure rear seat mounting bracket to rear fender. Alternately tighten nuts to 60-96 in-lbs (6.8-10.9 Nm). 5. If installing a new passenger seat, refer to the instructions included with the kit. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 6. If installing passenger seat, install passenger seat strap following the instructions in the service manual. 7. Install right and left side saddlebags following the instructions in the service manual. 1 2 3 2 1 is04121 1. Stud (2) 2. Nut (2) 3. Rear fender Figure 1. Rear Fender Install Rider Backrest NOTE Flaps shown removed for clarity of illustration. 1. See Figure 2. Turn backrest assembly (1) at a 45 degree angle clockwise to the seat. Slide the backrest shaft (2) through the flaps and into the receptacle in the seat. 2. While pushing down on the backrest assembly, twist the backrest counterclockwise until the shaft hits the stop. 3. Verify that the backrest assembly is locked in place by pulling up in the backrest pad