HARLEY DAVIDSON 45-AMP. UPGRADE ALTERNATOR ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
This 45-amp Rotor Kit is designed for installation on 1999 and later FLHT, FLHTC, FLHR, FLHRI, FLHRCI and FLTR Model Motorcycles. Existing Rotor Removal 1. Remove seat and disconnect battery terminals, negative cable first. 2. Follow instructions in applicable Service Manual and remove the primary chaincase cover. Remove the clutch, primary chain, compensating sprocket and shaft extension as a single assembly. 3. Remove the alternator rotor spacer, if present. Installation The laminated high-output rotor in this kit contains magnets that are considerably more powerful than those used in most previous rotors. The ROTOR REMOVER/INSTALLER and SHAFT PROTECTOR SLEEVE (HD-41771) must be used to prevent parts damage during rotor removal and installation. 1. See Figure 1. Verify threads are clean and thread the Shaft Protector and Rotor Remover/Installer, if removed. NOTE The Shaft Protector Sleeve not only protects the threads from the splines of the rotor, but acts as a guide to ensure that the rotor is properly centered. 2. Turn thumbscrews of Rotor Remover/Installer into threaded holes in rotor face. CAUTION 1 WARNING 1 WARNING 1 WARNING Kit Number 29999-97B Figure 1. Install Shaft Protector and Rotor Installer Engine Sprocket Shaft 1. Make Sure Threads are Clean 2. Install shaft protector sleeve. Shaft protector sleeve 3. Install Rotor Remover/Installer i04153 Handle Thumbscrew Forcing screw . Center ball on forcing screw in recess at end of engine sprocket shaft. Rotate the handle of the tool in a counterclockwise direction to ease rotor into position over stator. 4. Loosen thumbscrews and remove Rotor Remover/Installer. Remove Shaft Protector Sleeve. 5. Install the shaft extension on engine sprocket shaft. No alternator rotor spacer is necessary). 6. Follow instructions in applicable Service Manual and install the clutch assembly, primary chain and shaft extension as a single assembly. 7. Apply two drops of Red LOCTITE®262 to threads of clutch nut and engine sprocket nut. Tighten nuts as fol- lows: Clutch nut- (left hand threads), 70-80 ft-lbs (94.9-105.5 Nm) Engine sprocket nut- 150-165 ft-lbs (203-223 Nm). 8. Follow instructions in Service Manual and install the Primary Chaincase Cover using new gasket from kit, if necessary.

HARLEY DAVIDSON SADDLEBAG LID ORGANIZER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
installation NOTE Prior to installation, hold each organizer up to the lid (without removing the adhesive backing tape) to verify that the organizer fits properly within the recess of the saddlebag lid before moving on to the installation. 1. Use the isopropyl alcohol wipes included in the kit to thoroughly clean the interior surface of both saddlebag lids. Make sure any residue is removed, then allow the lids to dry completely. Make sure the lid surface is free of condensed moisture. NOTE The ideal temperature range for applying the tape is 70 to 100 degrees F (21 to 38 degrees C). Minimum application temperature is 50 degrees F (10 degrees C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere properly. 2. Locate the double-sided tape on back of the left lid organizer and remove the backing material. NOTE When performing the next Step, be sure to apply pressure to entire length of tape to ensure proper activation of pressure- sensitive adhesive. 3. Carefully center the left lid organizer in the left saddlebag lid recess and press firmly into place. While applying opposing force from outside of lid (to minimize force on tether, hinges, etc.), apply moderate pressure around entire perimeter of organizer and in middle (making sure to include all areas of tape contact). 4. Repeat Steps 2 and 3 on the right saddlebag lid with the right saddlebag lid organizer. 5. Allow the tape to cure (“wet-out”) for a minimum of 48 hours at 70 degrees F (allow extra time if temp is below 70 degrees). Do not place items in the Lid Organizer while the adhesive is curing

HARLEY DAVIDSON DYNA DOCKING HARDWARE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION Installing the Front Docking Point To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Remove the seat and disconnect the negative (-) battery cable. NOTE To keep the fender aligned, complete ALL the following procedures on one side of the motorcycle before starting the other side. 2. See Figure 1. Remove the stock fender support bracket. Position new rear fender mounting bracket from kit (5) into position. 3. Apply Loctite 243 (Blue) to button head bolt (2) prior to installation. Place the tapered side of front docking point (1) against the strut cover. Insert button head bolt (2) through the docking point, fender support and fender. Tighten to 12-18 ft-lbs (16.3-24.4 Nm) . 4. If used without saddlebags, install rear docking point (3) and recess cover (4) according to instructions in Part Number 53968-06C, Directional Relocation Kit. If used with saddlebags, mount rear docking point according to instructions with saddlebag kit. MAINTENANCE NOTE In time, the docking points may wear causing the mating luggage rack or sideplates to become loose. The fit may be tightened using the following procedure. If any fasteners with Loctite are loosened, then the fasteners must be removed, cleaned of existing Loctite and re-installed with new Loctite. 1. Loosen the docking hardware. 2. Rotate the docking points clockwise approximately 45┬░. 3. Tighten the docking hardware to the appropriate torque values as indicated in the installation procedures. This procedure can be repeated up to 3 times before replacement of the docking points is recommended.

HONDA GL18005 Passenger Floor Board Risers Installation Instructions

0

Filed Under (Honda) by admin on 23-12-2010

download
Flip the passenger floorboards in the up or closed position. Remove the four (4) allen bolts that attach them to the frame. Install the carriage bolts (round heads) into the backside of the risers (side opposite of recess for mounting screws). Then the plastic washer, next the floorboard, then a washer, lock washer and nut but do not tighten yet. Install the riser floorboard assembly back onto the frame using the original allen bolts and placing the aluminum spacers between the risers and the frame, tighten securely. Note: the curved slots should sweep up and back towards the rear of the motorcycle. You may reverse the left and rights so that the slots curve forward to gain further forward placement of the passenger’s feet if desired. Set floorboards to desired height and tighten securely

2000-2002 Aprilia Mille INSTALLATION INSTRUCTIONS

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1) It is a good idea to use Blue Loc-tite on all bolts you are about to remove and replace. 2) This kit has extremely close tolerances and in order for all the parts to clear the triple clamp and gas tank, you will probably have to loosen and align most of the associated bolts. We have tried very hard to make this as compact as possible but we know the factory tolerances vary from bike to bike. Be patient, the results are worth it. 3) Remove both front fuel-tank retaining bolts. You will use the longer bolts provided in our kit. 4) Install the frame bracket (part #22-6036-03) that mounts to your front (2) tank bolts holes. The frame bracket sits on top of the stock tank spacers. The frame bracket is offset. This means it fits correctly only one way, with the offset toward the triple clamp, part numbers facing forward, (see photo below). Due to the tight clearances on this model you’ll want to be sure the frame bracket does not make contact with the tank itself. It’s easier to start the tank bolts if you lift up on the tank slightly, while starting the new bolts into their threaded hole. Tighten the new tank bolts to 6 ft lbs. and use Loc-tite. 5) Remove the large 14mm Allen nut and washer that holds your triple clamp on. You will not re-use either one. 6) Install the new “Triple clamp damper mount” Part # 22-2925-00 into the recess area where the stock Allen head bolt was sitting. There is a machined recess or built-in-washer on the bottom of our mount to match the recess on your triple clamp. The 2 nubs that hang down, should match the rear contour of your triple clamp precisely. Use loc-tite and retighten the new 14mm Allen nut provided to your factory torque specs, usually a minimum of 35 ft lbs. and maximum of 85 ft. lbs. Do not use the stock washer that was under the original 14mm nut. 7) Grease the tower pin and drop it in the tower pin hole portion of the frame bracket. The tower pin is designed to “float” and requires no retaining devices. Keep the tower pin lightly greased! It should not touch the gas tank on the bottom side. 8) Install the stabilizer using the (2) 6×20 Allens with the slot in the link arm matching the tower pin. 9) Since the tank is rubber mounted at the rear, you want to be sure it won’t push forward and rub the frame bracket. After riding the first time, be sure the tank has not shoved forward by your body making contact with it. Remember, under heavy braking your entire body weight is pushing the tank forward. Until you have verified sufficient clearance between the tank and the tower pin, it might be smart to put something between the tank and tower pin to protect the tank. 10) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit, at 8 clicks out on the base valve, is a good starting point.