HARLEY DAVIDSON FLSTC & FLSTS DOCKING HARDWARE WITH SADDLEBAG SUP- PORTS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
The rear docking points in kit part number 90366-03 provide the rear mounting points for the Solo Rack. The rear mounting points from this kit ( 53931-03A ) will need to be installed to provide the clearance for the Solo Rack to be mounted. Table 2. Turn Signal Relocation Kit Requirement Turn Signal Relocation Kit Required Accessory Part Number 2003 and later FLSTC Not required 53815-00 Detachable Sideplates Not required 53066-00A Detachable Tour Pak Rack REMOVAL FLSTS Saddlebag Assembly Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Repeat steps 1 – 2 on the other side of the vehicle. FLSTC Saddlebag and Fixed Mount Sissybar Removal 1. See Figure 15. Remove a saddlebag by removing the acorn nut and washer on the lower support and the two flange locknuts inside the bag. Discard the flange locknuts, but retain the acorn nut and washer. 2. See Figure 1. Remove the saddlebag support studs and their mounting hardware. 3. Remove and discard fixed mount sideplates. Retain sissy bar for use with detachable sideplates. 4. Repeat steps 1 – 3 on the other side of the vehicle. 1 is06914 1. Saddlebag support studs Figure 1. Original Equipment Hardware (FLSTS model shown) INSTALLATION Docking Hardware Installation – For Detachable Sideplates or Tour-Pak Rack NOTE See Figure 15. The rear docking point (8) is wider than the front docking point (2). -J02425 1 of 5 1. Place front docking point (2) on front stud (1), with countersunk end of docking point facing fender support. 2. Place spacer (6) for side plates or mid docking point (for detachable sideplate kit) on rear stud (1). 3. Place rear docking point (8) on bolt (7), with countersunk end facing fender support. 4. Insert front stud (1) through front docking point (2), fender support and into bracket underneath fender as shown. 5. Insert rear stud (1) through fender support and into bracket underneath fender as shown. 6. Install bolt (7) through fender support and into bracket underneath fender as shown. 7. Tighten front and rear studs (1) and bolt (7) to 27 ft-lbs (37 Nm) . 8. Repeat steps 1-7 on the other side of the vehicle.

Incoming search terms:

HARLEY DAVIDSON FLHTCUSE TOUR-PAK INSTALLATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
INSTALLATION Prepare Motorcycle for Service 1. See the Owner’s Manual and remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Remove the bolt and negative (-) battery cable from the battery. 7 6 5 4 3 1 2 is01951 1. Loading coil assembly 2. Nut 3. Lock shroud 4. Clip, locking (Sold Separately) 5. Nut 6. Screw 7. Tour-Pak lockset Figure 1. Antenna Loading Coil and Tour-Pak Lock Installation 3. Remove the bolt and positive (+) battery cable from the battery. 4. Install a Tour-Pak Rack kit (53276-04, 53118-98A or 53260-02) according to the Instruction Sheet contained in the kit. 5. For FLHX and FLTR models: Install Antenna Relocation kit according to the instruction sheet in that kit. NOTE Discard antenna mounts from antenna relocation kit and use mounts supplied with this kit. To open the Tour-Pak prior to installing the Tour-Pak lock, insert a flat head screwdriver into the lock location and turn clockwise while pulling up on the lid. 6. Install the Tour-Pak onto the Tour-Pak Rack using the hardware included in the Tour-Pak Rack kit according to Instruction Sheet included with that kit. Install Tour-Pak Components

HARLEY DAVIDSON SOFTAIL DETACHABLE SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Detachable Saddlebag Configurations Table 1 provides a short description of the detachable saddlebag configurations. Table 1. Softail Detachable Saddlebag Configurations Accessory Configuration (Long Description) Short Descrip- tion Kit 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Other Detachable Accessories FL Outer 88237-07 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) Without Other Detachable Accessories FL Inner 2003-Later FLST/C and 2003-2005 FX Softail Models (Except FXSTD) With Rigid-Mounted Accessories FL Rigid 2006-Later FX Models (Except FXSTD) With Other Detachable Accessories FX Outer 88238-07 2006-Later FX Models (Except FXSTD) Without Other Detachable Accessories FX Inner 2006-Later FX Models (Except FXSTD) With Rigid-Mounted Accessories FX Rigid 2007-Later FXSTC Models With Stock Passenger Upright FXSTC Stock NOTE Proper installation of these kits requires that tasks be completed for one side of the motorcycle first before continuing to the opposite side. Install Turn Signal Relocation Kit Refer to instructions included with Turn Signal Relocation Kit 69857-07. Install Docking Hardware Kit(s) Without Other Detachable Accessories: Refer to instructions included with Docking Hardware Kit 53932-03. With Other Detachable Accessories: Refer to instructions included with Docking Hardware Kits 53932-03 and 88256-07. Install Rear Docking Adapter NOTE This procedure only applies to models without detachable accessories. 1. See Figure 1. Insert rear docking adapter (1) into holes in saddlebag bracket and hold in place. 2. Install rear docking adapter using screw (2) and nut (3). Tighten snugly.

Incoming search terms:

HARLEY DAVIDSON VRSC TURN SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Removing Turn Signals To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove the 40 amp Maxi-Fuse or disconnect the battery cables, negative cable first. Never touch the quartz bulb. Fingerprints will etch the glass and decrease bulb life. Grab the bulb with paper or a clean, dry cloth. Failure to do so could result in bulb damage. (00210a) 2. For VRSCA models, remove headlamp assembly. For VRSCB models, continue to Step 4. a. While facing the headlamp from behind (looking toward front of motorcycle), reach behind the headlamp bucket and twist the headlamp bulb approximately 45 degrees counterclockwise, then gently pull straight out of the headlamp. Repeat for remaining bulb. Temporarily secure bulbs out of the way for the following steps. b. See Figure 1. Remove the two mounting screws securing the headlamp bracket to the upper triple clamp and remove headlamp assembly. Save hard- ware

HARLEY DAVIDSON DIRECTIONAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect the negative (-) battery cable. INSTALLATION Installing the Turn Signal Stalk and Rear Docking Point 1. See Figure 3. Place the rear docking point (E) and recess cover (D) over the long threaded end of the new turn signal stalk (4) with the countersunk side of docking point facing outward. 2. Insert the turn signal stalk (4) through the rear mounting hole in the fender support and fender. Apply Loctite® 243 (blue) to the stalk and thread into fender mounting bracket. 3. Tighten the stalk to 12-18 ft-lb (16.3-24.4 Nm) . 4. Loosely install a jam nut (3) and a lockwasher (2) onto the short threaded end of the turn signal stalk (4). 5. Place the recess cover (1) into position over the recess on the turn signal housing. Insert the wires from the socket through the grommet into the turn signal housing, through the threaded hole and the recess cover, and into the turn signal stalk (4). NOTE Apply a drop of liquid soap to the wires to ease insertion through the stalk or use a thin wire to pull the wires through. 6. Route the wires through the turn signal stalk (4) until they are through the fender. 7. Install the turn signal housing onto the stud. Be careful that the wires are not twisted or damaged as the stalk and housing are assembled. The lockwasher will fit inside the hole in the recess cover. Hand-tighten the jam nut against the lockwasher. 8. While pulling the turn signal wires into the inside of the fender, guide the turn signal socket and grommet into the housing. 9. Align the rear turn signal housing so that when the lens is installed it is aimed rearward for proper visibility. While holding the turn signal housing in position, tighten the jam nut against the lockwasher to 8-10 ft-lb (10.8-13.6 Nm) . Connecting the Turn Signal Wires

HARLEY DAVIDSON FRONT TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
REMOVAL When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Purge the high-pressure fuel line and disconnect the fuel line following the instructions in the appropriate Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse following the instructions in the appropriate Service Manual. 3. Remove the seat following the instructions in the appropriate Service Manual. Save all seat mounting hardware. NOTE When moving the fuel tank back, do not damage the fuel gauge wires clipped to the frame under the left side of the fuel tank. 4. Remove the front and rear fuel tank mounting hardware following the instructions in the appropriate Service Manual. Move the fuel tank back on the frame to gain access to the tabs on the steering head harness shield. 5. See Figure 1. Disengage the tabs (2) from the holes (3) on each side of the frame and remove the shield (1). 6. Pull the wire harness down from inside the frame enough to disconnect the white (left) [31L] and black (right) [31R] 3-place turn signal connectors. Set aside the frame-side connector halves. 7. Remove the socket terminals from the lamp-side connector halves following the instructions in the appropriate Service Manual. Make note of the wire colors installed in the cavities of each connector, which should be: Left side (white connector): a. Black [BK] wire in cavity 1 b. Violet [V] wire in cavity 2 c. Blue [BE] wire (if installed) in cavity 3 Right side (black connector): a. Black [BK] wire in cavity 1 b. Brown [BN] wire in cavity 2 c. Blue wire [BE] (if installed) in cavity

HARLEY DAVIDSON FLTR DETACHABLE TOUR-PAK ANTENNA RELOCATION KIT

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
Drilling Instructions for Antenna Base Mounting and Cable Routing 1. See Figure 1. Measure and determine the center of the outside rear Tour-Pak wall. 2. Lay a strip of 2 inch wide masking tape from top to bottom over the approximate center. 3. Very carefully measure again and mark the center near the top of the tape strip. Measure and mark the center near the bottom of the strip. 4. Draw a line from the top mark to the bottom mark. 5. Facing the centerline you have drawn, measure 9-1/4 inches from the center line to the left side. 6. At the 9-1/4 inch dimension, lay a vertical strip of 2 inch masking tape from the top to approximately the middle of the Tour-Pak wall. 7. Very carefully measure again and mark 9-1/4 inches from the top of center line to the top of the tape strip. Measure and mark 9-1/4 inches from the bottom of the center line to the bottom of the strip. 8. Draw a vertical line from the top mark to the bottom mark. 9. Measure 1-1/4 inches from the top edge, down the vertical line you have drawn and draw a short horizontal line across the vertical line. 10. Measure 1-1/2 inches down the vertical line you have drawn from your FIRST short horizontal line and draw another short horizontal line across the vertical line

HARLEY DAVIDSON SOFTAIL TURN SIGNAL RELOCATION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 2. Raise the motorcycle on a floor jack to lower the rear wheel for fender hardware access. 3. See Figure 1. Remove two screws and tail lamp lens (1) from base (2). 2 1 is03243 1. Tail lamp lens 2. Tail lamp base Figure 1. Remove Tail Lamp Lens 4. See Figure 2. Using a Terminal Pick Tool (1), press locking tabs and disconnect turn signal connectors (2-place, Items 2 and 3) from circuit board. 5. Feed turn signal wiring and connector through opening in circuit board assembly and into rear wheel area. NOTE FXST/S/B tail lamp and connectors are positioned 180° from orientation shown in Figure 2. 6. Reach under fender to locate clips fastening turn signal wires in place. Carefully pull wires out of clips, and pull turn signal connectors and wires out from under fender. a. Remove two-inch (51 mm) section of conduit 4 inches (102 mm) from turn signal connectors. b. Cut black turn signal wire about 5-1/2 inches (140 mm) from its connector. c. Cut violet/brown turn signal wire about 4-1/2 inches (114 mm) from its connector. d. Save cut wires with respective turn signal connectors. 7. Remove the sissy bar and/or sideplate assembly, if equipped

HARLEY DAVIDSON SOFTAIL REAR SADDLEBAG GUARDS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION 1. Remove saddlebag, if equipped, from motorcycle. 2. Remove passenger footpeg or passenger footboard assembly (including footboard mount) from vehicle. 3. See Figure 1. Remove nut (1), seat strap bracket (if equipped) and 3/8 inch diameter bolt (2) from indicated position on rear fender support (immediately to the rear of the front seat) Discard the bolt, but save the nut for reinstallation. This location is where the upper part of the saddlebag guard will mount. 2 1 is03883 1. Rear fender support nut 2. Rear fender support screw Figure 1. Hardware Removal 4. See Figure 2. Install saddlebag guard (4) top flange (5) against fender support (3). Install 3/8-16 x 1-3/4 inch button head bolt with the seat strap bracket (if equipped) and hardware removed in Step 3 (if equipped) and nut in same direction as bolt removed in Step 3. Finger tighten only. 5. Position bottom flange (6) of saddlebag guard (4) against inboard surface of motorcycle frame (7) at location where passenger footpeg (2) (or passenger footboard bolt) attaches. If Heritage-Style Saddlebag relocation kit, Part Number 90238-00 is to be installed, the bracket should be positioned between the saddlebag guard flange and the motorcycle frame member. Follow installation instructions included with that kit. 6. See Figure 3. Determine your model application and follow the applicable installation procedure below: On models with passenger footpeg, but without saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support (B). Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Install lower saddlebag guard flange over bolt protruding from inboard surface of frame member. Install 3/8-16 lock nut to end of bolt. Tighten to 35-45 ft-lbs (47-61 Nm). Install footpeg (C) according to Service Manual instructions. On models with passenger footpeg and saddlebag relocation bracket: Install 3/8-16 x 2-3/4 inch socket head cap screw (6) (For 2007 FLSTC Models, use the 3.5 inch long socket head cap screw (7) from kit) through footpeg support. Install support to frame. Tighten support bolt to 35-45 ft-lbs (47-61 Nm). Position saddlebag relocation

Incoming search terms:

HARLEY DAVIDSON AM/FM ANTENNA RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Owner’s Manual and follow the instructions given to remove the left-side saddlebag. Gently pull the left-side cover from the frame downtubes (no tools are required), and remove the main fuse. 2. See Figure 1. Disconnect the antenna cable from the antenna base assembly (1). 3. Unscrew the antenna mast (2) from the antenna base, and set it aside for later installation. 4. Remove the lower locknut (3), and remove the antenna base from the mounting bracket (5). Save both locknuts, but discard the lockwasher (4). 5. Remove the two TORX® head screws (6) and lockwashers (7) retaining the antenna mounting bracket to the saddlebag rear support bracket (8). Discard the bracket and fasteners. 6. Carefully remove and discard any cable straps securing the antenna cable to the fender support and saddlebag rear support brackets. 8 9 6 3 2 5 7 4 3 1 is05436 1. Antenna base assembly 2. Antenna mast 3. Locknut (2) 4. Lockwasher 5. Original antenna mounting bracket 6. TORX head screw (2) 7. Split lockwasher (2) 8. Saddlebag rear support bracket 9. TORX Pan head screw and flanged locknut Figure 1. Original Antenna Mount 7. Remove and discard the TORX head screw and nut (9) that fastens the lower saddlebag support bar to the rear fender support bracket. 8. See Figure 2. Obtain the new antenna bracket (1), button head screw (2), flat washers (3 and 4) and flange nut (5) from the kit. NOTE If V-Logo Rear Fender Trim Rail Kit 91100-09 has been installed, the thick washer (4) is not used, and can be dis- carded.

Incoming search terms:

Incoming search terms: