Ignition Upgrade Module for 2004-up Carbureted Harley Davidson Motorcycles Owner's Manual

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
1. Disconnect the negative battery cable. 2. Grasp the sides of the electrical caddy (located next the ignition coil) and pull outward to remove. 3. Remove the relay and fuse panels from the electrical caddy. a. Insert a small screwdriver into the slot under each fuse and relay panel. b. Using a screwdriver, disengage the panel from the electrical caddy. 4. Disconnect the main fuse connector from the electrical caddy a. Remove the main fuse from the connector b. Insert small screwdrivers into the slots on each side of the main fuse c. Depress the tabs of the main fuse connector to disengage it from the electrical caddy
Thunder Heart Performance Corp. 615-672-8811 www.thunder-heart.com 2 EI5075.doc 5. Depress the tab located on the electrical caddy securing the TSM/TSSM. Pull it from the electrical caddy. Disconnect the TSM/TSSM connector. 6. Slide the data link connector towards the front of the motorcycle to disengage it from the electrical caddy. 7. Disconnect the ignition control module connector. 8. Disconnect the ignition coil connector and spark plug cables from the coil. 9. Remove the electrical caddy fasteners (3 total). 10. Remove the wiring from the electrical caddy. 11. Remove the fasteners securing the factory ignition control module from the electrical caddy. 12. Installation of the Digital Ignition Module is the reverse of removal. 2.2 Touring Models 1. Disconnect the negative battery cable. 2. Remove the right saddlebag. 3. Gently pull the side cover from the frame downtubes (no tools required). 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. Remove the two socket screws to detach the ignition control module from the electrical bracket. 6. To install the Digital Ignition Module, install and tighten the socket screws to 50-60 in-lbs . The remainder of installation is the reverse of removal. 2.3 Softail Models 1. Remove the seat. 2. Disconnect the negative battery cable. 3. Remove the two screws to free the ignition control module from the mounting bracket. 4. Depress the external latches and use a rocking motion to remove the electrical connector from the ignition control module. 5. To install the Digital Ignition Module, install and tighten the socket screws to 15-21 in-lbs . The remainder of installation is the reverse of removal

Incoming search terms:

WY50QT-30A SPECIFICATION AND OWNER MANUAL

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Meter and indicator light (Fig3) ⑴ Odometer ⑵ Speedo meter ⑶Fuel meter ⑷Parking light ⑸Right Turning signal light ⑹Voltage Meter ⑺Left Turning signal light (8) High-Low beam light ⑼Time meter Ignition Switch(Fig4) (1) On ()-when the switch turn to this position, Start engine and do not pull out the key. 。 (2) Off () When the switch turn to this position, Start engine power off and take out the key. ⑶ Lock () When the switch turns to lock position () , Take out the key .do not do any turning operation And do not start engine and light. 。 Notice : If the engine is idling speed for a long time in the hot climate, It will appear too hot Phenomenon Must close engine. Fig3 Fig 4 6 Fuel Meter(Fig 5) 1.Fuel Meter (Fig 5) show the approx remainder of flue. When the hand point to (F), it indicates Full tank of 7.5L. 。 2.When the hand at red section it indicates the remainder of flue is 1.8L. Headlight Switch (1) (Fig 6) Headlight switch: three position”" 、”"and”•” :When it on the position, the front head light, tail light, position light and meter light turn on. :When it on the position, tail light, position light and meter light turn on. •:When it on the position, the front head light, tail light, position lighted instrument turn off. Starting Switch (2) (Fig 6) Press this button to start engine(Ref.P16)

Incoming search terms:

Incoming search terms: