2001 – 2003 Highlander FRONT DOOR OPENING WEATHERSTRIP

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
have been improved to better resist deformation or tearing at the bottom center portion of the front door frame. Replace the front door opening weatherstrips on vehicles with this condition built prior to the VIN breaks listed in the Production Change Information section below. 2001 – 2003 model year Highlander vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE TYPE PRODUCTION CHANGE EFFECTIVE VIN 4Cylinder 4×2 JTEGD21A#30052511 Highlander 4 Cylinder 4×4 JTEHD21A#30020710 Highlander 6Cylinder 4×2 JTEGF21A#30085273 6 Cylinder 4×4 JTEHF21A#30113260 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 62311-48020-## Same Weatherstrip, Fr Door Opening, RH 1 62312-48020-## Same Weatherstrip, Fr Door Opening, LH 1 Replace the front door opening weatherstrip as shown in the Technical Information System (TIS). Refer to the 2001 – 2003 Highlander Repair Manual; Exterior/Interior Trim, Roof Headlining Assembly

Incoming search terms:

STEERING GEAR/ STEERING WHEEL REMOVAL AND INSTALLATION

0

Filed Under (Uncategorized) by admin on 05-10-2011

download
TEERING GEAR/STEERING WHEEL REMOVAL & INSTALLATION Page 3 of 4 STEERING GEAR/STEERING WHEEL INSTALLATION PROCEDURES (Cont’d) 2. Center spiral cable. a. Turn the cable counterclockwise by hand until it becomes harder to turn. b. Then rotate the cable clockwise about 2.5 or 3 turns to align the marks. (See Fig. 4) 3. Install the steering wheel. a. Align the matchmarks on the wheel and steering main shaft. b. Temporarily tighten the wheel set nut. c. Connect the spiral cable connector. 4. Bleed Power Steering System (when applicable). 5. Check steering wheel center point. 6. Torque steering wheel set nut. See the applicable vehicle’s repair manual for the torque specification. 7. Install and center steering wheel pad. NOTICE: Make sure the pad is centered and installed to the specified torque. If the pad has been dropped, or there are cracks, dents or other defects in the case or connector, replace the wheel pad with a new one. When installing the pad, take care that the wiring does not interfere with other parts and is not pinched between other parts. a) Connect the airbag wiring connector. b) Install the pad after confirming that torx screws are in the screw case. c) Using a torx socket, torque the screws to the specification in the vehicle’s Repair Manual. (See Fig. 5) d) Install the steering wheel lower cover

Incoming search terms:

TOYOTA TACOMA 2005 SUPERCHARGER FIT KIT

0

Filed Under (Toyota Manuals) by admin on 27-09-2011

download
are must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). • The TIS Repair Manual can be referenced for additional details. Please see your Toyota dealer for a copy of this document. 1. Installation Review and Vehicle Preparation. (a) Review the entire instruction instructions provided before beginning the installation (b) Review the parts list/kit contents to ensure that all parts are present before beginning the installation. If any items are missing contact Technical Support at (800) 688-5912 before proceeding. (c) Remove any low-octane fuel from the vehicle. Ensure that ONLY 91 octane or higher unleaded gasoline is used. (d) Place the vehicle onto vehicle hoist. (e) Protect the vehicle with protection blankets over the fenders and front of the vehicle. (f) Disconnect and remove the battery. (g) When draining the cooling system into a clean container in Step 7

TOYOTA ELECTRONIC TRANSMISSION CHECKS & DIAGNOSIS

0

Filed Under (Toyota Manuals) by admin on 16-09-2011

Download
The transmission requires regular maintenance intervals if it is to continue to operate without failure. As we discussed in previous sections, transmission fluid loses certain properties over time and especially due to heat. The Maintenance Schedules found in the repair manual or the Owners Manual indicate the appropriate replacement schedules based on how the vehicle is used. Schedule A for example, recommends replacement of the fluid every 20,000 miles or 24 months. Whereas Schedule B recommends just an inspection of the fluid every 15,000 miles or 24 months and no replacement interval. The chart below indicates which maintenance schedule to follow based on the use of the vehicle.

1994 TOYOTA SPECIAL SERVICE TOOLS

0

Filed Under (Toyota Manuals) by admin on 07-06-2011

Download
The following TSB contains information regarding the 1994 Special Service Tools (SST’s). Both the Essential and Available SST’s are listed by part number, tool name, model application, illustration / usage (for Essential SST’s only) and appropriate reference in repair manual. All Special Service Tools (SST’s) may be ordered by contacting OTC at 1-800-933-8335.

Basic Motorcycle Maintenance/ Repair Manual

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
1. Types of Motorcycles and Components a. Identify off-road, street bikes, three and four wheel cycles. b. Identify motorcycle components. 2. Demonstrate Safe Working Habits in the Shop. a. Demonstrate, list, and discuss personal safety habits. b. Demonstrate, list, and discuss shop safety. 3. Correct use of Tools (common and measuring) and Equipment a. Perform work on cycles using proper hand tools. b. Perform work on cycles using shop equipment correctly. 4. Specifications in a Shop Manual a. Locate engine tune-up specification. b. Locate engine lubrication and cooling capacities. 5. Identify and Describe Different Types of Fasteners a. Threaded and non-threaded. b. Nuts, bolts, and washers. c. Metric and English. d. Strength and Grade. e. Thread inserts. 6. Identification and Description of Engine Fundamentals a. Basic two cycle engine. b. Basic four cycle engine. c. Displacement and compression ratios. d. Horsepower and torque. 7. Disassembly, Service, and Reassembly of the Components of the Clutch and Final Drive Assembly a. Remove, measure and replace clutch components. b. Clean, lubricate, and measure chain. c. Clean and measure sprockets. d. Adjust and align rear wheel. e. Discuss shaft drive. 8. Service of Brakes, Tires, and Wheel Assemblies a. Service and adjust drum brake. b. Service disc brake caliper. c. True a wheel by adjusting spokes. d. Replace or repair a tire. 9. Attitudes and Work Habits a. Identify and develop positive attitudes toward tasks and fellow employees appropriate for the workplace, including giving and accepting criticism and praise. b. Identify and develop productive work habits, including attending to detail, completing tasks, maintaining the work setting and recording data. c. Identify and develop collaborative/teamwork skills, including solving problems in groups, building consensus, and responding to supervision

URAL motorcycles Installation and Removal Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
The Repair Manual provides information on setup, tune-ups, servicing, diagnosing problems, removing and installing components (otherwise referred to as “assembly units”), overhauling components, adjusting repaired components, and testing the repaired motorcycle. The increasing competition in the motorcycle market requires, more than ever, careful attending to the customer in order to assure the owner satisfaction with one’s motorcycle and to maintain customer confidence in the dealer and factory. It is important to repair the client’s vehicles correctly in a well organized and clean repair shop equipped with all necessary tools and parts. In such an environment, and having been trained at the technical training course, a repair technician will prove to be competent and efficient. Repairs on the engine and transmission especially, should be carried out in dust-free places. During breaks, disassembled transmissions and openings leading to the inner engine parts or lubrication holes should be protected from dust by clean rags. Valves, valve springs, spring retainers, rockers, pushrods, tappets, pistons, connecting rods and bearings should be put away in suitable boxes. Disassembled parts have to be cleaned and thoroughly checked for the following: Sliding and rolling surfaces for wear and freedom from scoring marks, all metal parts, particularly castings, tempered parts and welded joints as well for cracks and corrosion, and rubber parts for suitableness. As a rule, all gaskets and tab washers are to replaced upon reassembling. When disassembling parts, attention has to be paid to the arrangement of lock-washers on screws and nuts, spacing washers, gaskets, rubber mounts and so on. If necessary, mark mating parts in order to guarantee correct assembly.

Incoming search terms: