TOYOTA TACOMA (ALL 4WD, 2WD PRERUNNER, & 2WD TRD MODELS) 3" SUSPENSION LIFT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 27-09-2011

download
Before Starting Installation 1. Carefully read all warnings and instructions completely before beginning. 2. Verify all parts have been received in this kit by checking the parts list at the end of this document. 3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175. 4. Special tools needed: a. Coil spring compressor 5. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Ride Height 1. Measure ride height with the vehicle supporting its own weight on level ground. To settle the suspension, the vehicle should be driven forward at least 10 feet immediately prior to taking these measurements. Ride height is the measurement from the NOTE Kit parts are prefaced by the word kit and appear in bold print. NOTE Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper retention characteristics. This system may not include all replacement hardware as recommended by the factory service manual. Additional replacement hardware should be obtained prior to installation of this system to meet the requirements of the factory service manual

1990- 1995 TOYOTA 4RUNNER BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT

0

Filed Under (Toyota Manuals) by admin on 22-09-2011

Download
Disconnect both battery cables. Disconnect negative cable first, then positive cable Disconnect and move radiator out of the way. . Remove overflow hose from radiator spout. b. Remove four bolts securing radiator to core sup-port. c. Lift radiator up out of slots in core support. d. Straighten tabs on radiator. e. Lay radiator on fan while lifting body. 3. Relocate alternator ground strap if equipped Adhere to recommendations when replacement fasten-
ers, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended by the vehicle manufacturer that certain fasteners are replaced in order to maintain proper
retention characteristics. This system may not include all replacement hardware as recommended by the fac-
tory service manual. Additional replacement hardware should be obtained prior to installation of this system to
meet the requirements of the factory service manual.

2008 ALU-RACK TRIUMPH Street Triple 675 Mounting Instruction

0

Filed Under (Triumph) by admin on 06-11-2010

download
experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW-MOTECH takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts

TRIUMPH Tiger 1050 Nonshock GPS-Halter Cockpit Mounting Instructions

0

Filed Under (Triumph) by admin on 30-10-2010

download
Mounting Instructions SW-MOTECH products should be installed by a qualified, experienced motorcycle technician. If you are unsure of your ability to properly install a product, please have the product installed by your local motorcycle dealer. SW Motech takes no responsibility for damages caused by improper installation. All screws, bolts and nuts, including all replacement hardware provided by SW-MOTECH, should be tightened to the torque specified in the OEM maintenance manual for your motorcycle. If no torque specifications are provided in the OEM maintenance manual, the following torques may be used: All screws, bolts and nuts should be checked after driving the first 50 km to ensure that all are tightened to the proper torque. Medium strength liquid thread-locker (i.e., “Locktite”) should be used to secure all screws, bolts and nuts. Alle vom Motorrad gelösten Schrauben sind gemäß Herstellerangaben wieder zu montieren, oder mit von SW- MOTECH gelieferten Schrauben zu ersetzen. Falls nicht anderweitig definiert, diese Schrauben nach Tabelle anziehen. Gegebenenfalls Schrauben mit flüssiger Schraubensicherung einkleben. Prüfen Sie nach 50 km alle Verbindungen auf festen Sitz. GPS.11.458.10000/B Revision: 00 SW-MOTECH GmbH & Co. KG Ernteweg 8/10 35282 Rauschenberg Germany Tel. +49 (0) 64 25/8 16 8-00 Fax +49 (0) 64 25/8 16 8-10 info@sw-motech.com www.sw-motech.com M5 5,5 Nm M6 9,6 Nm M8 23 Nm M5 5,5 Nm M6 9,6 Nm M8 23 Nm 6 GPS.00.085.003 Anzahl/ Pcs. 2 Verbindungsblech Connector Lug 5 GPS.00.085.006 Anzahl/ Pcs. 1 GPS-Trägerblech GPS-Bracket 01 00 10 GPS.00.085.004 Anzahl/ Pcs. 2 Fixierblech Fixing Lug 9 M5 x 16 DIN 7380 Anzahl/ Pcs. 4 Linsenkopfschrau be Lenshead Screw 2 M8 x 50 DIN 6912 Anzahl/ Pcs. 4 3 Unterlegscheibe Washe

Incoming search terms: