YAMAHA YZF-R6R/ YZF-R6SR/ YZF-R6RC/ YZF-R6SRC SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING SPEC A Pass the right handlebar switch lead inside the front brake hoses and over the throttle cables. B Install the throttle cables to the hook so that the pulling side of the throttle cables is routed downward. C Pass the clutch cable through the guide. D Plastic locking tie shall be positioned at 10 mm (0.39 in.) below from the upper bracket. E Clamp the left handlebar switch lead to the front fork with the plastic locking tie and cut the tip of the tie. Clamp it to the protector section Set in the coupler between the head light’s hollow section and the duct. J Install the relay to the rib of the head light. (Location for the left and right relays is alternative.) K To the wire harness L To the front turn signal light (right) M Set the sub wire harness in the joint. N Do not catch the sub wire harness when the duct is assembled. O To the front turn signal light (left) P Point the tip of the plastic locking tie to the front side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in). Q Point the tip of the plastic locking tie under the under bracket and rear side of the vehicle. Cut the tip leaving 2 X 10 mm (0.08 X 0.39 in) A Pass the main switch lead under the left handlebar switch lead and then to the right side of the vehicle. B Pass the throttle stop cable by the left side of the side stand switch lead, oil level switch lead, A.C. magneto lead and then to the right side of the vehicle. C Pass the fuel tank drain hose and fuel tank breather hose inside of the reservoir tank breather hose, reservoir tank hose and wire harness and then route it by the out side of the starter motor lead. D Pass the coolant reservoir tank hose outside of the fuel tank drain hose and fuel tank breather hose. E Pass the fuel tank drain hose, fuel tank breather hose through the clamp of the coolant reservoir tank

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC ASSEMBLY MANUAL

0

Filed Under (Yamaha) by admin on 26-02-2011

download
PREPARATION To assemble the motorcycle correctly, supplies and working space are required. Supplies oils, greases, shop rags. Workshop The workshop where the motorcycle is assembled should be clean and large. The floor should be level. Self-protection Protect your eyes with suitable safety spectacles or safety goggles when using compressed air, when grinding or when doing any operation which may cause particles to fly off. Product hands and feet by wearing safety gloves or doing. SYMBOLS USED ON CRATE CARTON Contents of the transport package are fragile therefore it shall be handled with care. Indicates correct upright position of the transport package. Transport package shall be kept away from rain. Insertion of the lift arm from this side is prohibited. Lift arm inserting position. -1- UNPACKING 1. Remove the frame cover 1. NOTE: To remove the frame cover, cut the vinyl bands around the cover using a cutter or scissors. 2. Remove the bolts 2 (upper bracket). 3. Remove the bolt 3 (front tire). 4. Remove the packing frames 4 (upward and sideways). NOTE: Remove the bolts while holding frame. NOTE: Before starting the assembly, check for damaged or missing parts. The parts are contained in the cartan and the motorcycle for damage, scratches and other defects. -2- PARTS LOCATION 1 Carton box -3- 1 Carton box Screw, washer and special nuts (windscreen) Bolt (front master cylinder) Bolt (handle crown and handlebar) Nut (rear view mirror) Nut (front reflector) Front reflector Vinyl bag 1 Plugs (handle crown) Owner’s manual Rear view mirrors Windscreen – -5- 1. Handlebar 1 2 3 4 5 6 1 1 1 1 2 1 Reservoir tank (brake) Hexagon socket bolt Crown nut Hexagon socket bolt Cap Hexagon socket bolt * V * V V * d = 6 (0.24), r= 12 (0.47) d = 6 (0.24), r= 25 (0.98) d = 8 (0.31), r= 30 (1.18) 2. Front reflector A: Tighten the crown nut to specified torque. Tightening torque: 115 Nm (11.5 m • kg, 85.0 ft • lb) B: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 9.4 ft • lb) C: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 4.4 ft • lb) A: Tighten the screws to specified torque. Tightening torque: 40 Nm (4.0 m • kg, 29 ft • lb) 1 2 3 4 5 2 2 2 4 4 Reflector bracket Reflector Nut Washer Caliper bolt * V V * * d = 5 (0.20) d = 10 (0.39) d = 10 (0.39), r= 30 (1.18) 3. Clutch cable 1 Clutch cable 1 * A: Check the clutch lever for smooth action. CAUTION: Proper cable routing is essential to assure safe motorcycle operation. Refer to “CABLE ROUTING

Incoming search terms:

Suzuki SV1000 COOLING AND LUBRICATION SYSTEM REPAIR MANUAL

0

Filed Under (Suzuki) by admin on 25-02-2011

download
At the time of manufacture, the cooling system is filled with a 50 :50 mixture of distilled water and ethylene glycol anti-freeze . This 50:50 mixture will provide the optimum corrosion protection and excellent heat protection, and will protect the cooling system from freezing at temperatures above -31 °C (-24 °F) . If the motorcycle is to be exposed to temperatures below -31 °C (-24 °F), this mixing ratio should be increased up to 55 % or 60 % according to the figure. CAUTION • Use a high quality ethylene glycol base anti-freeze, mixed with distilled water . Do not mix an alcohol base anti-freeze and different brands of anti-freeze. • Do not rut in more than 60%anti-freeze or less than 50 %. (Refer to the right figure.) • * Do not use a radiator anti-leak additive. A WARNING COOLING AND LUBRICATION SYSTEM 5-3 20 40 60 80100 0 10 20 30 40 50 60 Density (%) Fig .2 Engine coolant density-boiling point curve • * You can be injured by scalding fluid or steam if you open the radiator cap when the engine is hot . After the engine cools, wrap a thick cloth around cap and carefully remove the cap by turning it a quarter turn to allow pressure to escape and then turn the cap all the way off . • * The engine must be cool before servicing the cooling system . • * Coolant is farmful; • * If the comes in contact with skin or eyes, flush with water. • * If swallowed accidentally, induce vomiting and call physician immediately . • * Keep it away from children . Anti-freeze density Freezing point 50% -31 °C (-24 °F) 55% -40 °C (-40 °F) 60% -55 °C (-67 °F) 50 % engine coolant including reservoir tank capacity Anti-freeze 1 100 ml (2.3/1 .9 US/Imp-pt) Water 1 100 ml (2.3/1.9 US/Imp.pt) Density (%) Fig.1 Engine coolant density-freezing point curve (°F) (°C) 302 150 (kgf/cm2) 284 140 1.5 c Q 266 130 0.9 0) a) :0 248 120 0.5 0) m Z3 230 110 0 (7 212 100 (F) (C) 32 0 14 -10 -4 -20 C 0 Q -22 -30 O) C N -40 -40 a) a) U- -58 -50 -76 -60 -94 -70 5-4 COOLING AND LUBRICATION SYSTEM COOLING CIRCUIT THERMOSTAT RESERVOIR TANK RADIATOR NO. 1 CYLINDER HEAD NO . 1 CYLINDER NO. 2 CYLINDER NO. 2 CYLINDER HEAD WATER PUMP INSPECTION Before removing the radiator and draining engine coolant, inspect the cooling circuit for tightness. • * Remove the body cowling. (=6-6) • * Remove the radiator cap ® . • * Connect the tester 02 to the filler. A WARNING Do not remove the radiator cap when the engine is hot. • * Give a pressure of about 110 kPa (1.1 kgf/cm 2, 15 .6 psi) and see if the system holds this pressure for 10 seconds. • * If the pressure should fall during this 10-second interval, it means that there is a leaking point in the system. In such a case, inspect the entire system and replace the leaking component or part. A WARNING When removing the radiator cap tester, put a rag on the filler to prevent spouting of engine coolant. CAUTION Do not allow the pressure to exceed the radiator cap release pressure, or the radiator can be damaged

Incoming search terms:

Incoming search terms: