2003 4Runner And Land Cruiser, 2004 Sienna SERVICE MAINTENANCE REMINDER LIGHT RESET PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 26-10-2011

download
should be used to reset the light when the oil has been changed. 2003 model year 4Runner and Land Cruiser vehicles. 2004 model year Sienna vehicles. To reset the Service Maintenance Reminder Light: 1. Turn the ignition switch to the “ON” position. 2. Set the Odometer / Trip Display to the “ODO” mode. 3. Turn the ignition switch to the “OFF” position. 4. Depress and hold the Trip Meter “RESET” button while turning the ignition switch to the “ON” position. 5. The Service Maintenance Reminder Light will: a. Illuminate solidly for 3 seconds. b. Blink for 2 seconds. c. Illuminate solidly for 1 second. d. Turn off. 6. Release the Trip Meter “RESET” button. 7. Turn the ignition to the “OFF” position. 8. Turn the ignition to the “ON” position, and confirm that the Service Maintenance Reminder Light goes out

Incoming search terms:

YAMAHA RX10H/ RX10SH RX10MH/ RX10MSH/ RX10RH/ RX10RSH SERVICE AND OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Throttle override system (T.O.R.S.) If the carburetor or throttle cable should malfunction during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the ignition and keep the engine revolution speed between 2,800 and 3,000 r/min if the carburetor fails to return to idle when the lever is released. Speedometer unit The speedometer unit is equipped with the following: a digital speedometer (which shows riding speed) an odometer (which shows the total distance traveled) a tripmeter (which shows the distance traveled since it was last set to zero) warning indicators (which show self-diagnosis, cool ant temperature, fuel level, and oil level warnings) fuel meter (which shows the fuel remaining in the fuel tank) grip/thumb warmer heat level indicator  (which shows the heat level of the grip warmer or the thumb warmer) After the engine is started, the tachometer 1 makes one sweep, and the warning light 2 and all segments of the meter 3 turn on and off once. Then the warning light turns on again, and then goes off if there are no problems. The grip warmer heat level is initially displayed for 5 seconds, then switches to the fuel meter display. Odometer and tripmeter modes Pushing the select/reset button 4 switches the display between the odometer mode “ODO” and the tripmeter mode “TRIP”. To reset the tripmeter, push the select/reset button for at least one second while the tripmeter is displayed. NOTE: @ To switch the speedometer, odometer, and tripmeter displays between kilometers and miles, select the odometer mode “ODO”, and then push the select/reset button 4 for at least 10 seconds. ESU00363 High beam indicator light The high beam indicator light 1  comes on when the high beams of the headlights are switched on. (See page 5-12 for headlight beam switch operation.)

HARLEY DAVIDSON COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
Removing the Old Speedometer NOTE This Instruction Sheet covers several different Harley- Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 3. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 4. Unplug the 12-terminal connector (39B) from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 5. Remove the back clamp: All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 6. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 7. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it doesn’t fall off during the following opera- tions. 8. Set the console securelyon the fuel tank. Installation and Final Check NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation. 1. Turn the console over, facing upward. 2. Place the speedometer gasket into position around the console speedometer bore. 3. Fit the new gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment. 4. Turn the console over, face down. 5. Install the back clamp

HARLEY DAVIDSON CHROME CONSOLE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation 1. See Figure 1. Remove and discard the two 1-1/4 in. (32 mm) long hex socket button-head screws (3) that secure the original console (1) to the fuel tank. 2. Remove and retain the 5/8 in. (16 mm) long hex socket button-head screw (4) securing the rear of the console to the rear of the tank. Lift the console and edging trim (2) from the motorcycle. 3. Lay clean shop towels on the fuel tank, flip the console over to expose the underside and lay it on the towels. 4. Unscrew the trip-meter reset button (12) and pull the reset switch (11) from the console opening. 5. Depress the connector tab and remove the 12-place connector [39B] (10) from the back of the speedometer (9). Depress the connector tab and remove the 12-place connector [108B] (7) from the back of the tachometer (6). 6. Remove and retain the four screws (14) and back clamp (13) from the speedometer and tachometer. 7. Turn the console over, face upward. NOTE When removing the speedometer and tachometer from the console, the gaskets may remain on the instruments. If this is the case, carefully remove them from the instruments for re-assembly to the new console. 8. Remove the speedometer and tachometer from the console (1). Carefully remove the gaskets (8) from the instruments. Move the console away from the vehicle. 9. Obtain the new Chrome console from the kit. Place the console on the shop towel-covered fuel tank NOTE Apply window cleaning fluid or mild soapy water to the instrument gaskets as needed to aid installation. 10. Place the speedometer gasket into position around the console speedometer (forward) bore. Fit the gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment.

Incoming search terms:

Incoming search terms: