1995 Camry WIPER MOTOR CIRCUIT BREAKER INSPECTION PROCEDURE

0

Filed Under (Toyota Manuals) by admin on 15-10-2011

download
INSPECTION PROCEDURE: Inspect the Wiper Fuse. Verify there is power and ground to the Wiper Motor on all speeds (including “Intermittent” or “Mist” if applicable). After verifying power and ground to the Wiper Motor, follow the procedure below to prevent unnecessary Wiper Motor replacement because of a temporary open in the Wiper Motor Circuit Breaker. 1) Disconnect the Wiper Motor Harness Connector. 2) Wait (10) minutes before checking continuity. 3) Check the continuity of the motor with an ohmmeter. REPRESENTATIVE CHECKING PROCEDURE: NOTE: Continuity check can be performed between either the low speed or high speed terminal and the ground terminal of the wiper motor. The standard resistance of a good wiper motor is approximately 1.5 to 4.5 ohm

Incoming search terms:

2003 – 2005 Sequoia, 2004 – 2005 Highlander, Sienna, And Tundra DIAGNOSTIC GUIDE FOR REAR SEAT ENTERTAINMENT SYSTEMS

0

Filed Under (Toyota Manuals) by admin on 08-10-2011

download
Check the power, ground, and TX+, TX- wiring between the RSE ECU and the display. Perform the following check without disconnecting any connectors. A. Using the EWD, check the resistance of the wires between the DVD player ground terminal or integrated DVD player/RSE display and chassis ground. The resistance of the wires should be below 1 Ω. Refer to the Technical Information System (TIS): applicable model year Wiring Diagrams. B. Check the resistance of the wires between the RSE ECU ground terminal and chassis ground. The resistance of the wires should be below 1 Ω. C. Check the voltage on the power terminals on the DVD player and the RSE ECU. Voltage should be greater than 12 V. D. Check the voltage between terminals TX+ and chassis ground and TX- and chassis ground at both the RSE ECU and the DVD player. Voltage should be between 2.0 V and 3.0 V Check the resistance of the wires between the RSE ECU and the radio/player. The resistance of the wires should be below 1Ω. C. Check the resistance of the wires between the RSE ECU and the radio/player to ground. The resistance of the wires should be 10 kΩ or higher

Incoming search terms:

Yamaha Roadliner And Stratoliners Brake Pedal Relocation Kit

0

Filed Under (Yamaha) by admin on 27-12-2010

download
1. This kit replaces the original rear brake actuating rod that connects the pedal to the master cylinder (see photo 1A) and the brake light switch spring (see photo 1B). Remove the two allen screws which attach the switches mounting plate to the frame (1C). Remove the spring. 2. Remove the cotter pin and washer from the forward end of the rod where it connects to the brake pedal (photo2A). Slide the rod over off of the brake pedal. Unscrew the rod from the threaded stud on the master cylinder. 3. Thread the new rod onto the stud until the end of the stud appears in the middle of the small sight hole that is cross drilled thru the rod (1D). Place the forward end of the rod back onto the brake pedal. Next check the distance between the bottom of the brake pedal and the top of the floorboard, this should be approximately 1 ¾”. If not, slide the rod off the pedal and thread it in or out to adjust the pedal height. With the rod on the pedal re-install the washer and cotter pin (Note: the cotter pin should go into the hole from the top down) then bend the cotter pin open. 4. Replace the brake light spring with the new one supplied. (Pushing down on the switches rubber cover will push the pin out). Re-install the switch bracket. Turn on the ignition and adjust the threaded collar on the brake switch so that the brake light comes on just as you feel some resistance when pushing on the pedal (when the brakes begin to drag).

Aprilia Futura 2003 Fitting Instructions.

0

Filed Under (Aprilia) by admin on 26-10-2010

download
vacuum r elbow. connection with tee piece in place, and dampe Route tubing as shown. We supply a piece of cottoiler tubing The black bracket has to be tilted back to Backing plate is available free of charge viton tubing, to protect our S around the exhaust pipe. It’s selected for its high temperature and oil/petrol resistance. allow light to shine on the number plate. from Scottoiler. This bracket has been rotated, mudguard re-drilled and remounted to ensure number plate illuminated.

Incoming search terms: