1100cc Honda Goldwing Installation Manual

0

Filed Under (Honda) by admin on 29-04-2011

download
Receiver Hitch Installation Install all bolts loosely until all brackets are in place 1) Place motorcycle on center stand and be certain it is level. 2) Remove saddlebags if necessary for easier installation. 3) Mount bracket A to the lower front crash bar bolt Left side (new bolts provided) and top of left hitch arm. 4) Mount bracket B to the lower front crash bar bolt Right side (new bolts provided) and top of right hitch arm. 5) Bracket C mounts to rear of hitch and sub frame bolt located behind tail light (new bolt provided) This bracket mounts inside the rear fender. 6) Attach brackets D and E to rear of hitch. 7) Bracket F attaches to bottom of bracket D and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 8) Bracket G attaches to bottom of bracket E and trunk sub frame with U-bolts. Insert bottom U-bolts at step 9 9) Brackets D and E (with brackets F and G) attach to bottom rear saddlebag sub frame with U-bolts. 10) Tighten all bolts. INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt. 5. Push the motorcycle off of the center stand and risers if used. 6. Bolt leanstop braces to hitch. (Bolt inserts from the bottom) Be certain to replace washers/spacers in the same configuration as when you removed them. see diagram next page 7. Check all bolts for tightness. 8. You are now ready for the test ride. A. Keep your feet up! B. Ride slowly in first gear until you are comfortable with the Tow-Pac system.

Incoming search terms:

HARLEY DAVIDSON HIGH PERFORMANCE CYLINDER STUD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit is designed for installation on 1986 and later XL model motorcycles. This kit is required on engines with compression ratios of 10:1 and higher. For XL 1200 engines with higher compression ratios, Screamin’ Eagle gasket kit part number 17046-98 is also recommended. Installation To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect the battery, negative cable first. 2. Remove top end heads and cylinders according to Service Manual instructions. Cylinder studs that are bent, scratched or broken must be replaced. Broken and bent studs distort clamp load, while scratches produce stress risers that may eventually lead to broken studs. Distorted clamp load causes head gasket leakage that may result in engine damage. Do not use a ratchet or breaker bar to install cylinder studs because they will bend the studs. 3. Remove existing cylinder studs according to Service Manual instructions. 4. Install new studs, Loctite end first. • Place a 0.313 inch DIAMETER BALL, HD Part Number 8860 (or from the XL clutch release mechanism) into the head bolt recess. Thread the stud into the head bolt until the stud bottoms on the ball. NOTE Pack clean shop towels into the crankcase openings to prevent the ball from falling into the flywheel compartment when removing the head bolt. • Clean the threads in the crankcase. • The studs have a Loctite patch on the crankcase end threads.Install the studs in the crankcase with the Loctite patch side down. • Use a T-handle to install the studs. Install studs until the free length is 4.84 ±.05 inches. See Service Manual for more detailed information. 5. Check all studs for proper height. 6. Reinstall the top end heads and cylinders according to the Service Manual Instructions

Kawasaki Spacers Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the tops of both risers and move the handlebars out of the way. Caution: Try not to turn your handlebars upside down. Air from the Brake/clutch reservoir may get into your line causing front brake/clutch problems. Put a towel or blanket on your bike to protect it. 2. Remove the two nuts that hold the risers on and remove the stock bolts from the risers. 3. Refer to fig 1. Install the new bolts through the risers, through Jim’s Spacers and through the triple tree. 4. Install the washers with locknuts and but don’t tighten them all the way. 5. Install the handlebars in the risers and install the top part of the risers. 6. Tighten the locknuts up insuring the handlebars are straight. 7. Double check that all fasteners are tight

Incoming search terms: