YAMAHA ROAD STAR WARRIOR PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 24-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side rider and passenger footpeg assemblies. (Save footpegs and bolts for future reassembly. Do not disconnect brake master cylinder plunger rod.) 2. Remove front cylinder exhaust port flange nuts. (Save) 3. Remove rear cylinder exhaust flange bolts. (Save) 4. Remove two bolts connecting muffler mounting bracket to lower frame rail. 5. Remove bolt connecting muffler to upper muffler bracket. Carefully remove complete system from motorcycle. (Assistance may be required.) Note : Apply tape on crank case area just in front of rear head pipe bend to protect paint during dissassembly and assembly. 6. Remove M6 x 35 button head screws connecting rear brake master cylinder reservoir to stock muffler bracket. (Do not disconnect hose. Save M6 x 35 button head screws.) 7. Remove stock upper muffler bracket. (Save M10 x 25 button head bolts for future reassembly.) VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install rear brake master cylinder reservoir bracket (stamped 333) using saved M10 x 25 button head allen bolts and supplied M10 lock nuts. (Refer to Figure 1) 3. Attach rear brake master cylinder reservoir to bracket (stamped 333) using saved M6 x 35 button head screws and supplied M6 lock nuts. (Refer to Figure 2) 4. Install and tighten megaphone mounting bracket (stamped 334) to frame using supplied M10 x 25 button head bolts. (Refer to Figure 3 & 4) If required, M10 flat washers are provided to space bracket away from frame casting ridge. 5. Unscrew all hose clamps (supplied) until they are completely loose. Mark top edge of front, rear, and collector heat shields with the location of mounting clips that are welded to

YAMAHA ROAD STAR WARRIOR BIG SHOTS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Remove right side rider and passenger footpeg assemblies. (Save footpegs and bolts for future reassembly. Do not disconnect brake master cylinder plunger rod.) 2. Remove front cylinder exhaust port flange nuts. (Save) 3. Remove rear cylinder exhaust flange bolts. (Save) 4. Remove two bolts connecting muffler mounting bracket to lower frame rail. 5. Remove bolt connecting muffler to upper muffler bracket. Carefully remove complete system from motorcycle. (Assistance is recommended.) Note : Apply tape on crank case area just in front of rear head pipe bend to protect paint during dissassembly and assembly. 6. Remove M6 x 35 button head screws connecting rear brake master cylinder reservoir to stock muffler bracket. (Do notdisconnect hose. Save screws.) 7. Remove stock upper muffler bracket. (Save M10 x 25 button head bolts for reassembly.) VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install rear brake master cylinder reservoir bracket (stamped 333) using saved M10 x 25 bolts and supplied M10 lock nuts (Figure 1). 3. Attach rear brake master cylinder reservoir to bracket (stamped 333) using saved M6 x 35 screws and supplied M6 lock nuts (Figure 1). 4. Install and tighten mounting bracket (stamped 336) to frame using supplied M10 x 25 button head allen bolts (Figure 2), If required, M10 flat washers are provided to space bracket away from frame casting ridge. 5. Place heat shields on a non-abrasive surface such as a blanket or carpet. Mark outside surface of front and rear heat shields with location of mounting

YAMAHA ROAD STAR WARRIOR OIL COOLER KIT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
INSTALLATION: 1. See FIG. F: Apply a thin film of oil to O-RING (#9) on OIL COOLER MOUNT ADAPTER (#2). Install the OIL COOLER MOUNT ADAPTER with OIL COOLER SUMP STUD (#6). Note that o-ring on adapter is mounted against oil filter sump. TIP: Only tighten “finger tight” at this point so adapter can move as needed to adjust oil lines. 2. See FIG. G: Install OIL LINES (#3 & #4) to OIL COOLER and OIL COOLER MOUNT ADAPTER as shown. Do not tighten fittings yet. NOTE: The shorter 9-3/4″ OIL LINE will be on the TOP fitting on the ADAPTER. 3. See FIG. H :Install OIL COOLER to frame with the BILLET OIL COOLER CLAMP (#7). Adjust OIL COOLER to desired position and tighten the three 10-24 X 1/2 SOCKET HEAD SCREWS (#8) securely. Rotate the OIL COOLER MOUNT ADAPTER as necessary to align the Oil Lines properly. WARNING: Make sure OIL COOLER is moved outward far enough so that it does not contact the Front Fender when the fender goes through its full range of motion! 5. See FIG. I & J: Tighten the AN fittings on the OIL COOLER MOUNT ADAPTER as shown with an 11/16″ open end wrench. Tighten the AN fittings on the OIL COOLER with an 11/16″ open end wrench. TIP: To prevent the OIL COOLER from turning when the fittings are tightened, place a thin screw driver or long allen wrench between the fittings as shown. NOTE: DO NOT USE ANY SEALANT ON AN FITTINGS! 6. See FIG. K : Tighten OIL COOLER SUMP STUD (#6). Re-install oil filter. Start the engine and check for leaks. Check oil level and top-off as necessary. MAINTENANCE:

Yamaha Road Star Warrior Fuel Injected Models INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove seat and fuel tank. 2. Remove airbox and left airbox cover. We highly recommend you consult the factory service manual for proper removal of airbox. 3. Route wiring harness under frame bracket towards airbox. (Fig 1) 4. Unplug stock black connector for fuel injectors. (Fig 2) 5. Plug Fuelpak 4-pin connectors in-line with the connectors from step 4. 6. Unplug the TPS connector and attach T-tap connector to the center wire (yellow). (Fig 3) 7. Route the Fuelpak violet wire to T-tap. (Fig 4) 8. Reattach the TPS connector. 9. Route black wire to the front of engine and down to the horn. (Fig 5) 10. Disconnect the factory black/white wire from horn. Plug Fuelpak into horn and plug Fuelpak black/white wire to Fuelpak connector. 11. Route black and green wires to battery negative. 12. Attach Fuelpak to Fuelpak harness and mount under seat as shown. (Fig 6) 13. Before reassembling the bike, make sure handlebar switch is in the engine-not-running position and turn the key on. Fuelpak should light up. Sound the horn. If Fuelpak turns off when the horn is sounded, recheck the black wire connection on the horn and that it is connected to the correct wire from the factory harness. 14. Follow the service manual to reinstall the airbox and gas tank. INSTALLATION INSTRUCTIONS FOR P/N 65005 READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION FUEL INJECTION MANAGEMENT SYSTEM ROAD STAR WARRIOR NOTICE: Fuelpak is intended for racing or off-highway use only, and is not legal for sale or use in California on pollution-controlled vehicles. PLEASE NOTE: FUELPAK USE REQUIRES A HIGH PERFORMANCE AIR FILTER. HOW IT WORKS ENTERING VALUES 1. Remove Fuelpak clear case cover by removing all four screws, save hardware . 2. Turn on main power with key, but do not start engine. Fuelpak display should light up, if not, turn power off and verify the connectors are fully seated. 3. Refer to Fuelpak Setting Reference to locate the Setting Values specific to your bike and exhaust system. If you do not find your setting, visit fuelpakfi.com or call tech support at (562) 921-0071. 4. Starting with mode 1 selected, press the value (+) or the value (-) buttons to input the correct value as indicated in your Setting Value. After entering your first value, press the mode select button to move to mode 2 and enter the value. Continue until you have entered the value for each of the first 18 mode positions. Each time the value (+) is pressed, the value increases by one number. Each time the value (-) is pressed, the value decreases by one number. (Please refer to the “How It Works” section directly above if you have questions about this step. 5. As the next procedure, after you have entered in your values for the first 18 modes, press the mode select button to move to mode 19. Fully twist open the throttle and return to idle position to calibrate the Fuelpak to your bike. 6. By pressing the mode select button twice, move to mode 21 and verify that it reads “0″ with the throttle closed, “50″ at approximately half-throttle and “99″ when fully opened; if not, repeat step 5. Do not proceed to step 7 until mode 21 is verified. 7. Enter any other mode values as required for your application. 8. Turn off power. 9. Reinstall clear cover, tuck Fuelpak under seat area and reinstall seat. 10. You are now ready to ride.

Incoming search terms:

WILD THINGS FUEL INJECTION CONTROLLER INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 26-10-2010

download
STEP 1 Determine a location for the Wild Things Module. Once the Wild Things Module location has been established, layout and cut the wires to length. STEP 2 Locate the switch power lead. We try most often to use the tail light switch power. If you locate the tail light connector we give you the color of the power wire within that connector. (Check the base settings page). Our information covers the most common application. STEP 3 The black wire from the Module is the ground. Again you have flexibility. You might choose the negative side of the battery. Or a common grounding lug, which your stock wire harness is using. Use the ring terminal for the ground, supplied in the kit. You may cut a section out of the ring out, allowing you to slip the terminal under the bolt. STEP 4 Locate the ECU. In the ECU harness, locate the injector wires and attach T-taps to these leads as shown in the illustrations on the suggested settings page. Connect the blue and gray leads from the TFI to these T-taps using insulators and spades as before, also, it does not matter which of the blue or gray leads attach to the injector leads. -cont.- BY DOBECK PERFORMANCE FITS: HONDA—’02-UP VTX1800; KAWASAKI—’99-UP VN1500/VN1600/VN 2000 (ALL EFI MODELS); SUZUKI—’04-UP 1600 MARAUDER/BOULEVARD M95; VICTORY—’98-UP ALL MODELS; YAMAHA—’02-UP ROAD STAR WARRIOR 9218-13MC-1005 WILD THINGS FUEL INJECTION CONTROLLER 9218 INSTALLATION STEP 5 Turn the key on and check for a flashing green LED. If yes, go to STEP 6. If you have no flashing green LED, re-check power and ground wiring. STEP 6 Start the bike. This unit is programmed to not add fuel at idle, this will cause all the LED’s to flash at idle, this is normal. If just the green or red LED’s continue flashing after startup, an injector wiring error is indicated. If the green LED is flashing re-check the blue wire from the TFI is connected to the proper wire of your bikes stock harness. If the red LED is flashing re-check the gray wire from the TFI is connected to the proper wire of your bikes stock harness. Make sure you have the correct wires selected in the stock harness.