Honda 400EX Hub installation instructions

0

Filed Under (Honda) by admin on 20-12-2011

download
Remove all contents from its packaging and verify that all parts are present and free from damage. You should have the following items: (2) wheel hubs (2) smaller tapered bearings (2) large tapered bearings (2) wheel bearing nuts (2) dust caps (2) inner bearing seals (6) M3 x .5 screws (2) cotter pins (2) inner bearing spacers 2. Completely remove the old hubs from your quad and clean the spindle and the surrounding areas. It is very important to keep the new bearings and seals clean during installation for long life. Be sure to remove the factory inner bearing spacers from the spindle and discard. They will not be used in re-assembly. 3. Pack your new Timken tapered wheel bearings with a liberal amount of high quality wheel bearing grease. A wheel bearing packer works best, however you can accomplish the task by placing the grease in the palm of your hand and manually working it in between the bearing rollers. We also recommend that you pack the area between the bearing races in the hub with grease for additional lubrication and protection against moisture. 4. Place the large wheel bearing (inner) into the hub and install the inner seal. The seal should bottom out against the step in the bore and the face should be flush with the hub. 5. Remove the brake rotors from your old hubs. Re-install the rotors on your new hubs and be sure to use medium strength Loctite on the threads. 6. Apply a light film of grease or oil to the large diameter of the spindle stud. Install the new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from running dry. Install the hub onto the spindle and slide the outer bearing over the spindle and install the new bearing nut furnished with your hubs. Do not use the factory nut or washer. 8. SETTING THE BEARING PRELOAD: It is first necessary to seat the bearing before setting the preload. This aligns the rollers and prevents the bearings from loosening after a short period of use. To seat the bearing, tighten the spindle nut while you rotate the hub until the hub becomes difficult to spin. With the bearing now seated, you must set the bearing preload. Preload means placing a small amount of force against the bearings to remove any clearance between the bearing race and the rollers. This is done by backing the nut off completely and re-tightening it with your fingers. Do not rotate the hub while setting the preload . If a hole in the spindle is not accessible for installation of the cotter pin, adjust the nut tighter to bring a hole into alignment. Install the cotter pin and bend the pin around the outside of the nut. Do not attempt to bend the pin toward you (over the end of the spindle) or it may rub on the inside of the dust cap.

Incoming search terms:

KYMCO MXU 375 ATV WINCH MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kymco) by admin on 26-10-2010

download
WINCH MOUNT INSTALLATION INSTRUCTIONS 1. Remove molded plastic bumper guard from the ATV. 2. Mount the winch mount weldment (Item 1) to the ATV as shown below. 3. Mount the roller hawse to the winch mount weldment as shown above. 4
4. Mount the winch to the winch mount weldment and route the winch cable through the rollers. (Installer may need to remove rollers to allow cable end to pass through). 5. Wire the winch according to the manufacturer instructions. 6. Re-install the molded plastic bumper guard. 5 *CAUTION BE AWARE OF WHEN THE CABLE STOP CONTACTS THE ROLLER HAWSE AS CABLE IS WOUND IN. FAILURE TO RELEASE MAY CAUSE DAMAGE TO WINCH PARTS OR TO THE ATV. When using the winch to raise and lower a blade a cable stop must be installed. Carefully raise the blade until the top of the push tube’s are no closer than 1″ anywhere on the ATV. Place the Cable Stop onto the Winch Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using the Cable Clamp Assembly as shown in the pictures below.

Incoming search terms:

Kawasaki Winch Mount Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. You will need to remove the lower Front Moulding of the ATV for installation of the Winch Kit. 2. Position the Winch with the motor on the LEFT side in the mounting location and slide the Winch Mount Plate in under the winch. Attach the Winch Mount Plate to the frame with the U-bolts and Nylock Nuts provided. Tighten at this time. See Picture Winch Mount Plate 3. Install the Roller Hawse Bracket to the Lower Winch Plate and to the front bars (behind the bars) of the ATV using the U-bolts, Carriage Bolts and Nylock Nuts. See Picture Below. Winch Mount Plate Roller Hawse Bracket 4 4. After winch installation is complete, reinstall lower Front Moulding of ATV. Remove one of the long rollers and the two side rollers and feed the winch cable through the roller hawse. Reinstall the rollers and be sure rollers move freely. Attach the Roller Hawse to the Roller Hawse Mount Plate using the 3/8″ x 1″ Bolts and Nylock Nuts provided with the winch. Tighten all hardware

Incoming search terms:

Incoming search terms: