MPS Sport Bike Auto Shift Installation Manuals

0

Filed Under (Suzuki) by admin on 21-02-2012

download
The first thing to do is remove the seat, fuel tank, and possibly the front fairing if equipped. You will need plenty of room to work. Electrical Connections – You will need to locate and test a few things on your bike before you start wiring. A good ground, an ignition switched 12 volt power source, the horns, and the ignition coils. We have plug n play style harnesses available for some bikes. Check the web site for specific models. Control Box Wiring Coils – Most four cylinder motorcycles use either a individual firing system or a waste spark system. Waste spark is by far the most common. All four cylinder bikes with only two coils use a waste spark system. Most late model four cylinder sport bikes use waste spark systems even though they have four individual coils. Bikes with a waste spark systems will need the 360 calibrated unit. The 360 calibrated Sport Bike Autoshifts are identified by the 360 engraved into the box below the wire lead exit. The P/N for these boxes has the 360 as a suffix. (P/N 1-0299-360) Some of the newest fuel injected bikes (Hayabusa, GSXR1000, ZX12) that have cam sync sensors are individual firing. These bikes will require 720 calibration and will have no outside identifiers and the P/N 1-0299. The Sport Bike Auto Shift has four brown wire leads that are connected to the negative of each individual coil on a four coil system. You will notice that the connector for the four brown wires has a molded in ridge that marks the brown wire that is used as the rpm sensor. This must be connected to the number one cylinder coil negative wire.

Dellorto Motorcycle Carburetor Tuning Guide and INSTALLATION

0

Filed Under (Tips and Review) by admin on 04-02-2012

download
Installation angles The tapered-needle-type Carburetor s with concentric, central float chambers have a horizontal main barrel and can be mounted up to a maximum inclination of 40 degrees from the horizontal (figure 3) . For
applications on motocross and trials engines, etc, this inclination should be 30 degrees or less. fig. 3 2.4 Engine connections The Carburetor is usually connected to the engine with one of the following : Male clamp fixing : the male clamp connection used for the flexible fixing of the Carburetor to the engine is usually recommended on motorcycles for motocross, trials, etc or fitted to engines which run to high rpm or those which produce strong vibrations. fig. 4 Female clamp : the female clip connection and the flange connection, with a rigid fitting to the engine, are usable on road motorcycles or fitted to engines which do not generate very strong vibrations

ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

HERO HONDA CD100 CHHEDA ELECTRICALS & ELECTRONICS INSTALLATION

0

Filed Under (Honda) by admin on 13-11-2011

download
These are intelligent CDI’s using variable-advanced timing where the firing angle is varied according to the engine RPM in order to maximise both the power output as well as the engine efficiency.
Built with the latest technology and infrastructure to offer high reliability and superior performance.

Kawasaki FI Calibration Tool Instruction Manual

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
System Function Kawasaki FI Calibration Tool (FI Tool) is developed to modify the mapping of the racing machine to gain operating conditions suitable for the course and the rider’s skill. The following are the available setting functions. Table 1 FI Tool Function Model Name Functions Available Setting Range ’04 ZX-10R ’05 ZX-6RR ’05 ZX-10R ’06 ZX-10R ’07 ZX-6R 1) Adjust the injected fuel rate at acceleration -30 % ~ +30 % 〇 〇 〇 〇 〇 2) Adjust the injected fuel rate of No.1 and No.4 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 3) Adjust the injected fuel rate of No.2 and No.3 cylinder -30 % ~ +30 % 〇 〇 〇 〇 〇 4) Adjust the injected fuel rate of primary and secondary injector * -30 % ~ +30 % -10 % ~ +10 % — – — 〇 — – — – — 〇 5) Adjust the ignition timing -15°CA~ +5°CA 〇 〇 〇 〇 〇 6) Adjust the sub-throttle opening angle -50 % ~ +50 % -45 % ~ +45 % 〇 — – 〇 〇 — 〇 — – 〇 7) Adjust the exhaust device opening angle -50 % ~ +50 % 〇 — 〇 〇 — 8) Adjust the all injected fuel rates of all cylinders and operating are a simultaneously -30 % ~ +30 % 〇 〇 〇 〇 〇 9) Adjust the value of engine over revolution limiter 0 ~ +300 rpm -1000 ~ +700rpm -1000 ~+1200rpm — – — 〇 — – — 〇 — – — 〇 〇 — – 10) Set the fuel cut or not at deceleration Use or Not Use 〇 〇 〇 〇 〇 11) Set the sub throttle controlled or not Controlled or Full Open Fixed 〇 — – — – 12) Set the exhaust device controlled or not Controlled or Full Open Fixed 〇 〇 〇 〇 〇 13) Set the Auto Shifter Ignition Cut Length Controlled or not, set Ig. Cut Time by gear range — – 〇 〇 〇 14) Set the Pit Road RPM Limit Controlled or not, set Upper Limit RPM by gear range

BMW Motorcycles F 650 GS/Dakar Driveability Issues

0

Filed Under (BMW) by admin on 12-11-2010

download
Concern: Customer complains about hesitation, surging and stalling when the engine is operated at low to medium RPM. Service Measure: In the event of a customer complaint on the above concerns, please check the following points, adjusting to specification as necessary: Fuel pressure: Measure fuel pressure under all operating RPM. If fuel pressure is outside of specification, replace fuel filter with pressure regulator. Recheck fuel pressure, with new components installed, to confirm fuel pressure is to specification. Fuel pressure specification = 3.5+/- 0.2 bar Clutch adjustment: Clutch may not disengage completely with engine cold. Oil in the viscosity range 20W50 may be in use. Insure that the clutch is adjusted correctly and change oil to viscosity range 10W50. Control unit update: Using the BMWMoDiTeC CD 8/x, Update 3, update the programming of the BMS COMPACT control unit. The update of a BMS COMPACT control unit program is not to take place unless a customer has a complaint about hesitation, surging and stalling, these complaints have been verified by the retailer and the service measures covering fuel pressure, clutch adjustment and oil viscosity have been completed. Important Note: Always comply with the instructions, as included with the update CD, for the correct installation of CD 8/x, Update 3. Identification Label: Print a new identification label ( YELLOW for update ) and affix it to the BMS- COMPACT control unit. Please note that it is not permissible to deliver an updated motorcycle to a customer without the correct identification label affixed to the control unit.

Incoming search terms:

CAGIVA V -RAPTOR 1000 AKRAPOVIC SLIP- ON INSTALLATION MANUAL

0

Filed Under (Cagiva) by admin on 10-11-2010

download
the power curve is increased evenly throughout the entire rpm range, with no unmanageable drop-outs, which indicates the correct tuning of the Akrapovic SLIP-ON system. The stock curve is especially improved right at the peak of the power band, where the system really shows its racing roots. TORQUE the stock torque curve is smoothed out and increased with the use of the Akrapovic SLIP-ON system. Unwanted fluctuations are greatly eliminated, making the motor more rider-friendly, and the torque range is extended. The Akrapovic SLIP-ON system guarantees weight savings, a full 7.50 kg in the case of the titanium link pipe version. Lighter weight means better handling in all maneuvers. Thus it is a very important factor in ensuring increased safety. The sound deserves special mention. The roar of the large big two-cylinder through the Akrapovic SLIP-ON system will turn a lot of heads and strengthen the reptilian image of the Cagiva.

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

1991 Bimota YB10 DYNOJET KIT INSTALLATION MANUAL

0

Filed Under (Bimota) by admin on 01-11-2010

download
1. Remove the vacuum slide from the carbs. Remove the stock needles & spacers, noting the order of assembly (Fig.A). 2. Install the Dynojet needles on groove #3 , using all stock spacers (Fig. A). Install the Dynojet washer above the E-clip. 3. Replace the stock slide springs with Dynojet slide springs provided. 4. Remove the stock main jets and replace with the Dynojet main jets provided. Use the DJ116 main jets with stock exhaust pipe, or use the DJ120 main jets with aftermarket header or slip-on with high flowing baffles. Use the DJ112 main jets at high altitude. Be sure that the jets you are changing are the main jets. 5. Locate the fuel mixture plug (Fig. B), if you see a screw head, proceed to adjusting procedure. With the plug drill (DD #5/32) provided, carefully drill thru the plug(s). The mixture screw is directly underneath this plug, be ready to pull back on the drill the instant you break thru. Use the screw provided to secure and remove the plug. Carefully turn mixture screw clockwise until seated, then back out 3 turns. 6. Locate the main air correctors (Fig.C). Using the plugs provided (DCO400), plug the main air passage. Place the plug in the carb flat end first.Tap in lightly. Using DT002. STAGE ONE INSTRUCTIONS Fig. B Place E-clip in groove #3 from the top Fig. A Notes: 1. Proper EXUP value adjustment is very important for good midrange performance. 2. If experiencing fueling problems below 4,000 rpm, under full throttle, that the needle can’t fix, try changing fuel level. If you feel it is too rich, lower the fuel level. If you feel it is too lean, raise the fuel leve

MPS Electronic Engine Kill Installation Instructions

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
blue wire should be connected to the normally open pole of the shift button. The Shift Button is a momentary type switch. The common pole of the shift button should be connected to a good ground and the normally open connects to the blue wire from the Electronic Engine Kill box. Electric Air Valve – The Electric Air Valve has two wires. These wires are interchangeable. One needs an ignition switched 12 volt power source. The other needs a ground signal when the shift button is depressed. The easiest way to do this is to locate the red and blue wires in the Electronic Engine Kill wire harness. Splice one Electric Air Valve wire into the red wire and splice the other Electric Air Valve wire into the blue. Once again soldering is the preferred method but you can use schotchlok splices. Setting Kill Time – Kill time is the amount of time the engine stays dead between gears during a shift. Generally the shorter the kill time the quicker the shift. The proper kill time will vary from bike to bike. Its generally better to start with to much kill time and work your way quicker. We generally start at around 75 ms. of kill time. The Kill Time is adjusted via a small potentiometer accessed through the grommet on the front of the unit. Using a small screwdriver Carefully turn the pot clockwise to the end of its travel. This is 100 ms of kill time. Now, carefully turn the pot screw counterclockwise to the end of its travel. This is 50 ms of kill time. Halfway in between is 75 ms. The pot only goes from 7 oclock to 5 oclock so don’t force it, they break easily! Testing The System – With no air in the system start the bike. Bring the rpm up to around 3000 rpm and push the shift button. You should hear a slight hesitation in the engine each time you depress the shift button. Once you establish that you have a engine kill when pushing the shift button remove the clevis pin from the shift cylinder and extend the shaft to the end of its travel. Air up the shifter to 120 psi. We also have onboard compressor kits available to conveniently fill the air tank on the fly or high pressure CO2 systems that can shift hundreds of times without refilling. With the engine off and the key on push the shift button