HARLEY DAVIDSON COMBINATION SPEEDOMETER/TACHOMETER GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-04-2011

download
Removing the Old Speedometer NOTE This Instruction Sheet covers several different Harley- Davidson models and years. Make sure you locate and follow the procedures that apply to the motorcycle receiving the new gauge. 1. Apply power to motorcycle and record the odometer reading. 2. Remove the seat according to the procedure in the applicable Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. NOTE Cover the fuel tank with clean shop towels to prevent scratching. Damage to the finish could result. 3. Remove the instrument console acorn nut (and mounting screw with a flat washer on some models). Lay clean shop towels on the fuel tank. Lift the console from the fuel tank, turn it upside down and lay it on the towels. NOTE If necessary, bend back the flexible metal clip to free the harness conduit from the underside of the console. 4. Unplug the 12-terminal connector (39B) from the back of the speedometer. Depress the external latches and use a rocking motion to separate the pin and socket halves. 5. Remove the back clamp: All models except FXSTD: Gently pry the three latches upward to release the back clamp from the back of the speedometer. FXSTD: Depress the three external legs of the lock ring, then gently pry the three latches upward to release the back clamp from the back of the speedometer. 6. Unscrew the trip-meter reset button, and pull the harness from the clamp (remove the screw if necessary). 7. Lift the console and remove the old speedometer from the console. Discard the old speedometer, but retain the rubber gasket and back clamp for use with the new gauge. NOTE Set the console securely on the towel-covered fuel tank, and take care that it doesn’t fall off during the following opera- tions. 8. Set the console securelyon the fuel tank. Installation and Final Check NOTE Apply window cleaning fluid or mild soapy water to the speedometer gasket as needed to aid installation. 1. Turn the console over, facing upward. 2. Place the speedometer gasket into position around the console speedometer bore. 3. Fit the new gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment. 4. Turn the console over, face down. 5. Install the back clamp

HARLEY DAVIDSON ROAD KING FORK LOCK COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
INSTALLATION 1. See Figure 1. At the handlebar cover, carefully pry under black plastic area of the lock plate and remove the lock plate. Discard the lock plate. 1 2 is00632 1. Lock plate 2. Pry location Figure 1. Remove Fork Lock Plate 2. See Figure 2. Remove and discard the two Phillips cover screws beneath the lock plate. 1 is00633 1. Cover screws Figure 2. Remove Cover Screws 3. See Figure 3. Obtain the rubber gasket (4) and flat spring (3) from kit. Place the gasket over the mounting location and align the screw holes. Place the flat spring over the gasket and align the screw holes. 4. See Figure 3. Obtain two chrome socket head screws (2) from kit. Place the cover assembly (1) into position, and install screws to secure cover

HARLEY DAVIDSON CHROME CONSOLE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
Installation 1. See Figure 1. Remove and discard the two 1-1/4 in. (32 mm) long hex socket button-head screws (3) that secure the original console (1) to the fuel tank. 2. Remove and retain the 5/8 in. (16 mm) long hex socket button-head screw (4) securing the rear of the console to the rear of the tank. Lift the console and edging trim (2) from the motorcycle. 3. Lay clean shop towels on the fuel tank, flip the console over to expose the underside and lay it on the towels. 4. Unscrew the trip-meter reset button (12) and pull the reset switch (11) from the console opening. 5. Depress the connector tab and remove the 12-place connector [39B] (10) from the back of the speedometer (9). Depress the connector tab and remove the 12-place connector [108B] (7) from the back of the tachometer (6). 6. Remove and retain the four screws (14) and back clamp (13) from the speedometer and tachometer. 7. Turn the console over, face upward. NOTE When removing the speedometer and tachometer from the console, the gaskets may remain on the instruments. If this is the case, carefully remove them from the instruments for re-assembly to the new console. 8. Remove the speedometer and tachometer from the console (1). Carefully remove the gaskets (8) from the instruments. Move the console away from the vehicle. 9. Obtain the new Chrome console from the kit. Place the console on the shop towel-covered fuel tank NOTE Apply window cleaning fluid or mild soapy water to the instrument gaskets as needed to aid installation. 10. Place the speedometer gasket into position around the console speedometer (forward) bore. Fit the gauge into the bore so that it fits snugly against the rubber gasket. Rotate the gauge into approximate visual alignment. The back clamp will complete the alignment.

Incoming search terms:

HARLEY DAVIDSON LED FUEL GAUGE KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Removing the Analog Fuel Gauge NOTE The fuel gauge wires are routed through a tube in the fuel tank, and are secured by a clip at the bottom of the tank and, on some models, a clamp on the frame. Open the clip and clamp as needed, and be sure there is enough slack in the wires to be able to lift out the gauge. 1. At the bottom left side of the fuel tank, bend back the flexible clip slightly to free the fuel gauge conduit. Open the harness clamp on the frame if necessary to free the conduit. Gently pull on the conduit to draw the Multilock connector [117] out of the tunnel. 2. See Figure 2. Depress the pin on the socket terminal side of the connector, and pull apart the pin and socket halves. 3. See Appendix B in an appropriate Service Manual. Use a pick (Snap-On TT600-3 or equivalent) to remove the terminals or clip off the wires. Remove and discard the fuel gauge. 4. For Carbureted Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge just far enough to free it from the fuel tank. Disconnect the two sending unit connectors. Feed the conduit and two wires up through the tube while removing the gauge. Remove and discard the fuel gauge. For Fuel-Injected Models: See Figure 2. Remove the fuel gauge by firmly grasping and carefully pulling up (do NOT twist) on the gauge to free it from the fuel tank. Feed the conduit and three wires up through the tube while removing the gauge. Remove and discard the fuel gauge. 5. Remove and discard the rubber gasket. INSTALLATION For Kit Numbers 75084-04B or 75237-03B 1. See Figure 2. Assemble the new gasket (3) to the LED fuel gauge (1) from the kit. Install the gasket so the flat side contacts the edge of the gauge. 2. See Figure 1. Use three of the Phillips-head screws and washers from the kit to connect the wires as follows: Fasten the Orange wire (1) ring terminal to the gauge connection marked “12V and “O” with a screw and washer. Fasten the Black wire (2) ring terminal to the connection marked “GND” and “BK” with a screw and washer. Fasten the Yellow/White wire (3) ring terminal to the connection marked “Y/W” with a screw and washer. 3. See Figure 2. While carefully lowering the fuel gauge, feed the wire harness (2) down into the drain tube until the three short (Orange, Black, Yellow/White) wires exit the hole at the bottom of the fuel tank. Gently pull the wires to remove slack while installing the gauge to the fuel tank. Do not twist the gauge during installation. Hold the gauge firmly and press down until it snaps into place

Incoming search terms:

Cobra TSB2108 JR And OI Radiator Cap Installation Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Cobra will send a spacer (ECMU0555) to all OI / JR customers with silver radiators. Assembly instructions are listed below. If the customer is uncomfortable with the installation process, they may send the cap to their dealer or back to the factory for installation. Spacer installation 1. Start the process by removing the rubber gasket. Stretch it to elongate the center hole (yes it will stretch a long way). 2. Once the gasket is stretched sufficiently, pull it back over the center crown to remove. 3. With the rubber gasket removed, place the spacer centered crown on the cap. 4. With the spacer in place, lightly pry up the center crown with a small screwdriver . 5. With the center lifted, stretch the gasket and work it’s hole around the center crown. 6. When completed it should look like this.

FXR and Softail TOP FUEL 14MM DRIVE INSTALLATION

0

Filed Under (Tips and Review) by admin on 31-10-2010

download
1. Install oil line fittings on back side of motor plate, cut hose to make 2 pieces, top fitting is for oil return ( oil out of filter), bottom fitting is for oil feed ( oil into filter). 2. Install motor plate with alternator cover over engine spacer and install the 2 standoffs. Be sure that the motor plate is aligned properly. Fig. 1 Fig. 2 Fig. 3 3. Install threaded oil filter mount on front side of motor plate, grease rubber gasket on oil filter and install hand tight. (Fig. 4 & 5) Install starter pinion gear supplied with kit. (See PG-100 Installation). Fig. 4 1 Fig. 5 Fig. 6 4. The pictures below refer to special bushing enclosed which is used only to install front pulley, it is a tool only and must be removed after front pulley is installed. (Fig. 7) Fig. 7 5. Refer to 3″ Electric Start Installation for FXR #5 & #6 for proper procedure for alignment. 6. For final installation remove pressure plate and clutch pack for easier handling and place belt on both pulleys and with special bushing in place,(#4 above) and install belt drive onto engine and trans shaft simultaneously. (Fig. 8) Fig. 8 7. Make sure writing on belt is facing towards you. (Fig. 9) Fig. 9 VERY IMPORTANT! APPLY RED LOCTITE TO SPLINED HUB OF REAR BASKET BEFORE FINAL INSTALLATION. (Fig. 10) 2 Fig. 10 8. Install engine shaft nut and torque to Harley specifications. An electric impact may be used.

Incoming search terms:

Victory Freedom Engines Installation Instructions for S&S Air Cleaner Kit

0

Filed Under (Victory) by admin on 31-10-2010

download
1-Locate and remove the Intake Air Temperature Sensor (IATS) from the stock Polaris Victory air box. Locate the new position for the IATS on the bottom of the S&S air cleaner. Push the IATS in the lower air cleaner cover and turn1⁄ 4 turnin either direction, make sure you feel it lock into place. Inspect from the inside of the air cleaner to ensure that the barbs are locked into place. See Picture 1. 2-Using the stock Polaris Victory air box gasket (PN 5811908) and S&S supplied (Qty 4) M6 fasteners, assemble the lower air cleaner cover to the throttle body using 243 Blue Loctite®on the treads. Torque the M6 fasteners to 72-96 inch pounds. 3-Position the S&S pre-formed air filter onto the lower air cleaner cover ensuring that it fits into the machined groove. 4-Install the top air cleaner cover on top of the filter ensuring that it fits into the machined groove. 5-Make surethat the filter is situated in the machined grooves on both the top and bottom air cleaner covers. 6-Using 243 Blue Loctite on the threads of the S&S supplied (Qty 3) M6 fasteners tighten down top air cleaner cover evenly until seated. Finish torque the fasteners to 72-96 inch pounds. Now you’re ready for breather hose and barometric pressure hose routing. 7-Locate the S&S supplied 3⁄ 16 “reinforced hose and clamps. Push one end of the hose on the 3⁄ 16 “brass barb in the bottom air cleaner cover and slide clamp up around the end of the hose. The other end of the hose is for the Barometric Pressure Sensor (MAP). Route the hose towardthe back of the engine over the top of the rear rocker cover. 8-Remove the MAP sensor from the stock Polaris Victory air box. Remove the orange rubber gasket from the MAP sensor. Slide the S&S supplied clamp over the 3⁄ 16 “rubber hose that leads to the air cleaner. Push the barbed end of the MAP sensor into the 3⁄ 16 ” rubber hose and slide clamp up to the end of the hose around the barb. A small amount of lubricant may be applied to the barb on the MAP sensor to make installation easier. 2 S&S Air Cleaner Assembly 41-0021 (Calibration cardnot shown) Picture 1 CAUTION WARNING WARNING Plastic barb locked in recess.
9-Assemble and install breather hose as follows: A-Cut the stock Victory®hose on the straight section just behind the 90 degree bend as shown in Picture 2 . B-Slide an S&S supplied 1⁄ 2 “hose clamp over the modified stock breather hose. C-Install the S&S straight barb in Victory breather hose and position a hose clamp around hose end. D-Slide the 90-degree end of breather hose over the brass barb on the air cleaner cover and slide hose clamp in place. E-Position straight end of the S&S breather hose over the 1⁄ 2 “barb to connect to the Victory hose. Slide clamp over connection. F- See Pictures 3 and 4 for breather hose and barometric pressuresensor hose installation positions. NOTE: S&S breather hose can be cut for best fit

Incoming search terms:

KAWASAKI ZX-6R/ RR Carbon Fiber /Aluminum Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1 After bike is cool make sure the bike is secured before beginning the installation. 2 Remove the fairing retaining clips and mounting bolt. Remove the stock mid pipe and muffler. 3 Apply a small amount of high temperature silicone (such as Permatex Ultra Black) to the inside of the exhaust inlet. 4 Attach the LOR exhaust canister to the slip-on tube adapter with the spring tabs aligned (make sure your hands are protected with a pair of gloves in case the tubes slip). You may have to squeeze the mid-pipe adapter tube to fit into the exhaust inlet as the mandrel bends may become slightly out of round due to a cut near the bend (the tube will take form once connected). Slide the canister all the way until the slip-on adapter seats fully against the exhaust inlet. Wipe off any excess silicone. 5 Place each spring over the exhaust side spring tabs and use the spring tool to pull the springs over the adapter spring tabs. Both springs must be secured for proper installation. 6 Apply a small amount of silicone sealer (such as permatex Ultra Black or Ultra Copper) to the inside (inlet side) of the slip-on adapter. Slide the low profile barrel clamp over the LevelOne Adapter pipe. Slide the slip-on adapter pipe over the stock header collector. Do not fully tighten the barrel clamp. 7 Place the round canister clamp with the rubber gasket over the rear of the exhaust and slide to the clamp location. Insert the original stock screw and 8mm washer through the exhaust clamp and finally through the foot peg. Mount the clamp to the outside of the stock muffler bracket. On the opposite side (towards the bike) place the stock 8mm lock washer and stock 8mm nut and start the thread. Do not fully tighten at this time. 8 Standing at the rear of the motorcycle, check the alignment of the muffler. You can adjust/rotate both the exhaust and mid-pipe adapter until the muffler is aligned properly. 9 Once everything is aligned fully tighten the exhaust canister clamp. 10 Fully tighten the low profile barrel clamp over the stock header. 11 Before you start the bike make sure all fingerprints and dirt have been removed from the canister and slip-on adapter. You may use rubbing alcohol to clean the slip-on adapter. After 75-100 miles check all bolts, etc for tightness. It is recommended to apply some light – medium grade thread locker to prohibit any bolts from loosening under the vibration from the bike. 12 Enjoy your LevelOne Racing exhaust system