Honda TRX 450R 2006 Rear Grab Bar INSTALLATION AND REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2011

download
To avoid injury or damage to your ATV, read these instructions before installation. 1. Parts List: Item Part Name Description Qty 1 H062060 Grab Bar 1 2. Preparation: a) Lock rear brake on bike. b) Remove OE grab bar, retaining all mounting hardware. c) Remove 3 OE rubber grommets from OE grab bar. 3. Installation: a) Install 3 rubber grommets on Pro Race Grab Bar.. b) Install Pro Race Grab Bar on bike, reusing all hardware and mounting locations. 4. Maintenance: Check fasteners for tightness and re-torque as required. 5. Care and Cleaning: Clean using mild soap. 6. Customer service: For further information call Pro Armor at 951-270-0559

HARLEY DAVIDSON SOFTAIL REAR LOWERING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Prepare the Motorcycle 1. Follow the Service Manual instructions to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect the negative (-) battery cable from the battery. 3. Place motorcycle on a lift and secure the front wheel. 4. Use an overhead crane or hoist attached to the frame to lift the rear of the motorcycle to allow the rear fork to pivot through its range of travel. 5. Place a screw jack under the rear wheel to support and adjust the rear fork during shock removal, installation and ride height adjustment. Be sure rear wheel is supported when removing rear shocks. If wheel is not supported rear fork can drop down, which could result in death or serious injury. (00481b) Removal 1. See Figure 1. Remove the bolt and washer (1) that fasten each of the shock absorbers (2) to the rear fork. NOTE Snap-on Tool Co. adapter, Part Number SRES 24, is necessary to gain access to the shock absorber bolts. 2. Remove the flanged locknut (6) and cup washer with grommet (5) fastening the shock absorber to the frame bracket (4) and remove the shock absorber. 3. Remove, inspect and, if necessary, replace the rubber grommets, the cup washers (5), and the bushing (3). 4. Repeat for the other shock absorber. Disassemble the Shock 1. Thoroughly clean the rear fork end of the shock, especially near the shock canister seal. 2. Support the rear fork end of the shock absorber and shock canister on the table of a press. 3. Press on the shaft to compress the spring in the canister until the keeper plate drops down away from the retaining ring.

Incoming search terms:

KAWASAKI VULCAN 1500 PRO PIPE HS EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the mufflers by loosening the pinch clamps on the front of each muffler. 2. Remove the muffler mounting bolt from the right side passenger footrest, slide the mufflers off and set them aside. Note: Save the mounting bolt, it will be reused for installation. 3. Loosen the pinch clamp on both front and rear head pipes, they’re located at the resonance chamber (the black box where the pipes meet). 4. Remove the two acorn nuts that mount the head pipe to the cylinder head. Remove the two piece header flange and set it aside. 5. Remove the front head pipe by rotating it down and pull it out of the resonance chamber. 6. Remove the two acorn nuts and flange from the rear head pipe. Remove the two bolts from either side of the resonance chamber and lower rear pipe and resonance chamber down and out and set it aside. 7. Remove the rubber grommets at the resonance chamber mounting points. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the new mounting bracket (stamped 317) to the inside of the stock muffler mounting point (Refer to FIG. 1). 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of all three heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear and collector heat shields. To facilitate the installation of the collector heat shield use a forward sliding motion from the rear of the collector. Do not force the collector heat shield directly onto the collector as damage to the heat shield will result. Note: the collector heat shield uses the 3/8″ wide clamps. 3. Rotate the hose clamps in the shields so that the screw drives are accessible. Tighten only finger tight at this time. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Check to be sure that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 5. Install the header with the heat shields attached, to the front and rear cylinders using the stock nuts and bolts. Leave them loose at this time. 6. Slide the chrome muffler clamp (supplied) onto the inlet end of the megaphone. Install the 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by the 5/16″ lock nut (hardware supplied). Leave the clamp loose at this time. 7. Slip the megaphone onto the head pipe collector, engaging the collector heat shield between the clamp and the outer slip joint tube. Slide one dog bone shaped nut plate under the bracket that

Incoming search terms:

KAWASAKI VULCAN 800 STRAIGHT SHOT EXHAUST SYSTEM INSTALATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header flange nuts from the front and rear head pipes. 2. Remove the acorn nut located under the rear muffler. 3. Remove the two allen bolts located under the front muffler. 4. Remove the stock exhaust system from the motorcycle and set it aside. 5. Remove the two hex head bolts that attach the stock muffler mounting bracket to the frame of the motorcycle. Remove the muffler bracket and set it aside. 6. Remove the two rubber grommets and spacers from the stock muffler and the one grommet and spacer from the muffler mounting bracket. Set them aside with the the two mounting bolts, they will be reused during installation. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install a chrome header flange onto the front and rear head pipes. 3. Install the heat shield to the front head pipe using the two hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe with the heat shield attached, to the front cylinder using the stock nuts. Leave them loose at this time. 5. Install the rear head pipe, with the heat shield attached, to the rear cylinder using the stock nuts. Leave them loose at this time. 6. Install the stock rubbber grommets and spacers into the three large holes on the V&H mounting bar (See figure 1). 7. Slide one dog bone shaped nut plate under the bracket that is welded to each muffler. 8. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Do this to each muffler but leave the clamp loose at this time. 9. Install one muffler to the four hole bracket welded to the V&H mounting bar using the two 5/16″ flange bolts (supplied) and leave them loose. (See figure 1) 10. Slip the muffler and mounting bar assembly onto the front head pipe while aligning the grommet holes in the mounting bar with the holes in the frame.

SUZUKI GSXR1300R SLIP-ON'S INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 17-12-2010

download
1. On the right hand side of the motorcycle, remove the Allen bolt holding the rear of the fairing to gain clearance to the tail pipe clamp (Figure 1). 2. Loosen the two tail pipe clamps, one on each side of the motorcycle. 3. Loosen and carefully remove the muffl er mount bolts and muffl ers. NOTE: Take care not to let the muffl ers drop against the swingarm as they are quite heavy. 4. If gaskets remain on the stock head pipe remove them. As they will not be re-used in this application. 5. Remove the steel inserts and then the rubber grommets from the mount locations on the left and right passenger footpeg hangers. NOTE: Spraying a little contact or brake cleaner on the rubber will soften it up for a few seconds while you push out the inserts and grommets. The steel inserts and rubber grommets will not be re-used and will be replaced by aluminum spacers in this application

Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

Kawasaki ZX-14 Indy Series Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove and place the lower fairings in a safe place, to separtate them unhook the rivet at the bottom. The right side lower fairing will need to be trimmed for proper exhaust clearance. Remove the fairing knee panels. Two rubber grommets retain the panel after bolt removal, light force is required to pull panel off. Remove the tank cover. Four rubber grommets and two plastic hooks retain the panel after bolt removal, pull outward to remove from grommets then pull forward and up, light force is required. Remove mid fairing sides. Undo pushpin located on the fairing backside. Note: Blinker connectors must be disconnected before pulling the fairing too far. Remove the left and right muffl ers. Remove the stock header. Note: Be careful not to damage the radiator while removing the stock header and installing the new header leaving the fl ange nuts loose at this time. Install both collectors 7-40020 and 7-40022 holding them to the headers install the four springs 7-30002 from the header to collector spring tabs. Install collector 7-40014 by installing two springs 7-30002 from collector to collector spring tabs. Note: A small amount of WD-40 at the pipe joints will help to fi t them together. Install the megaphone on the header assembly using one of the original muffl er mounting bolts and nuts removed in step 6, mount the megaphone to the forward muffl er mount located at the footpeg. Tighten the header nuts and then remove the megaphone. At this point the right side lower fairing needs to be trimmed. A template is supplied (Page 4) to outline the clearance cut that is needed on the right side lower fairing, we recommend using a dremel tool or a die grinder. The template should give you the necessary clearance but some fi tments may vary. After making the cut lightly sand the edges being careful not to scratch the paint. Clean all fi ngerprints from the exhaust using contact cleaner (or other non fl ammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. Try a test fi t. If you feel more clearance is needed, mark the fairing and remove it, trim until there is at least a 1/4″ of clearance. Reinstall the megaphone and check that the O2 plug is tight. You are now ready to start your motorcycle. Check for exhaust leaks and oil leaks. Shut off the bike and re check the oil level