2008 Harley Davidson Touring models with an electronic throttle Grips Installation manual

0

Filed Under (Harley Davidson) by admin on 08-03-2012

download
1. Using a sharp knife, remove the rubber from your current grip by carefully cutting it away from the existing plastic throttle sleeve. The rubber that is adhered to the plastic sleeve must be ” shaved” resulting in a smooth plastic sleeve with no rubber. 2. Apply glue to the throttle sleeve. Use about 1/4 of the tube of glue on each side. Most of the glue should be applied to the end of the sleeve away form the throttle housing. 3. Slide the grip on to the throttle sleeve with one strong push. Use a rubber mallet if needed. Be sure not to get any of the glue into the space between the throttle sleeve and the throttle housing as well as the space between the throttle sleeve and the handlebar. *Wipe up any excess glue immediately

Yamaha V-Star 650 Engine Guard REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Protect the rear portion of the front fender with a towel or other thick, soft cloth. Remove the OEM engine guards if they have been installed on the motorcycle. Your new Barons engine guard will fasten to the frame at the same points as the OEM guard and will use the same hardware. 2. Or, if OEM engine guards are not present, remove the 14mm bolts from the underside of the drivers footpeg mounts. 3. Remove the 12mm upper engine mount bolts located on both sides of the frame. Replacement bolts are included with your new engine guard. 4. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 5. Raise the guard until the holes in the lower mounting brackets align with the vacated bolt holes beneath the drivers footpegs. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the large washers (supplied with the guard) between the rear face of the lower bracket and the frame. The washer fills the space between the lower mounting bracket and the footpeg mount. Reinsert the 14mm bolts and finger tighten. 7. Rotate the guard until the holes in the upper mounting brackets align with the empty holes on each side of the frame. 8. Insert the replacement 13mm bolts, along with their washers, and tighten securely. Tighten all other nuts and bolts securely. 9. Remove the protection on the front fender and you’re ready to ride. CAUTION!!! You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

TOYOTA TACOMA 2005 SPARE TIRE LOCK Procedure

0

Filed Under (Toyota Manuals) by admin on 21-10-2011

download
1. Lower Spare Tire. (a) Lower spare tire using hooked jack handle supplied in the vehicle tool kit. 2. Install Spare Tire Lock. (a) Install the spare tire lock assembly on the lowering screw by lining up the cross pin in the lock with the slot in the lowering screw. (b) Tap lock in place with a rubber mallet until it is fully seated. (Pull on lock to ensure attachment.) (c) Install adapter shroud (protects cable and spring) using slotted washer. (See Fig. 2-1) 3. Install Key on Hooked Jack Handle. (a) Install key on hooked jack handle, pressing the jack handle into the slot in the key until the clip snaps in place

Incoming search terms:

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

HARLEY DAVIDSON TOURING CHROME PASSENGER FOOTBOARD PAN KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Installation 1. See Service Parts illustration. Remove socket head cap- screw (2) from footboard support (3). Place support on a clean flat surface. 2. From bottom of footboard (1), use a small flat blade screwdriver to push rubber beads on pad (5) up through holes in footboard. Remove pad from footboard. 3. Using a brass drift and rubber mallet, tap two retaining pins (4) toward center of footboard and remove. 4. Remove footboard from support bracket taking care to remove and retain detent ball (6) and spring (7) from footboard support (3). 5. Insert spring (7) and detent spring (6) into footboard support (3). 6. Place new chrome footboard pan in position with footboard support and insert retaining pins using a brass drift and rubber mallet. 7. Moisten rubber beads on pad with soapy water. Place pad into position on footboard. From bottom of footboard, use needle nose pliers to pull rubber beads down through holes in footboard. 8. Engage nubs on inboard corners of pad with holes in foot- board. 9. Install socket head cap screw into footboard support and tighten 120 in-lbs (13.6 Nm). 10. Repeat procedure for other passenger footboard

Yamaha Road Star Engine Guard Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1. Protect the rear portion of the front fender with a towel or other thick, soft cloth. 2. Remove the OEM engine guards if they have been installed on the motorcycle. Or, if OEM engine guards are not present, Remove the two lower engine mount bolts. These bolts are located on the inside of the right and left frame rails, and will be replaced with the longer 10mm bolts included with your new engine guard. 3. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 4. Raise the guard until the upper V” mount is located between the frame rails. Note: Your new Barons engine guard is equipped with a unique upper V” mount clamp. This clamp becomes a cradle for the upper frame supports when it is inserted between the frame rails. 5. Rotate the engine guard until the lower mounting brackets are aligned with the lower engine mount holes. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the new 10mm bolts and washers, and finger tighten only. 7. Tighten each 3/8″ bolt in the upper clamp evenly by using a 9/16″ socket or a wrench. Snug down each bolt until it draws the front of the upper clamp into contact with the upper frame supports, then adjust these bolts accordingly to achieve equal spacing between each floorboard and the lower engine guard rail. 8. Tighten the jam nuts against the washers to lock each bolt in place. CAUTION! It is critical that you do not over-tighten these bolts. Tighten all remaining nuts and bolts securely. If necessary, slightly loosen rear brake line banjo bolt and rotate banjo fitting for clearance with engine guard. Tighten banjo bolt and check brake for proper operation. You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

Ducati Sport Clutch Lever INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 26-10-2010

download
1 To remove your stock lever, use a 19mm wrench or (adjustable wrench) to remove the large sheet metal nut attached to the main pivot bolt that holds the lever. (Photo 1a) Once the locknut is removed, push the main pivot bolt out with your finger or if necessary tap lightly with a rubber mallet or plastic handle end of a screwdriver (Photo 1b) After the pivot bolt is removed, the lever will detach from the master cylinder. (Photo 1c) 1a See other side for further instructions INSTALLATION INSTRUCTIONS FOR PART # CRC552 ® C/5 Sport Clutch Lever Part # CRC552 1b 1c INSTRUCTIONS_CRC552 12/27/07 10:05 AM 23 4 2 Included with your ASV lever is a plastic bag that contains a custom pivot bolt, spacer & locknut. These parts will replace the OEM Brembo parts that were used with your stock lever. 3 Carefully place the lever into the master cylinder while aligning the plunger rod into the plunger cup on your ASV lever as shown in photo 3. 4 Align the lever and the master cylinder pivot bolt holes and Install the main pivot bolt, you will need to pre-load the lever into the master cylinder to get the bolt through the holes. The bolt head has two cut outs on the sides that need to be aligned with the matching area on the master cylinder. Be sure the head of the bolt seats down into the slotted area of the master cylinder. It may be necessary to use a rubber mallet or Plastic end of a screwdriver (Photo 4) to tap the head of the bolt down into its slot. 5 On the other side of the pivot bolt where the threads are, you will see that there is space around the pivot bolt. You will need to install the aluminum spacer that was supplied in the plastic bag with the pivot bolt and locknut. The spacer has a small flange on one side. The flange should be on the outer side when installing it into the hole surrounding the bolt. (Photo 5a) You may need to use pressure to seat the spacer fully into the hole surrounding the pivot bolt. You should be able to do this by using your fingers or thumbs as shown in photo 5b.