Suzuki Electronic Jet Kit Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
at anytime during install or tuning please callus for any and all help, we can’thelpifyoudon’tcall ) 1. Before installing the TFI you must first disconnect the negative lead from the battery. 2. Determinea location for the TFI unit. Suggested locations areas follows: Under the seat, behinda side cover or tail section. 3. The TFIcomeswitha harness with injector connectors that match the factory injector connectors. 4. Locate the factory fuel injectors (see owners manual if you are not sure).** **: Some models are equipped with two sets of injectors (primary and secondary); the unit is designed to interface with the primary injectors. If the TFI harness does not match your injectors do not proceed and call tech support at 877-764-3337. 5. Disconnect the factory injector connectors from the fuel injectors and replace with the TFI injector connectors from the TFI unit, basically unhook the factory injector connector and plug the matching TFI connector (female) to the injector and then connect the factory injector connector to the TFI connector that simulates the injector (male). There is no order to hookup the TFI harness to the factory harness just make sure the original factory connector goes toits’original cylinder. It isa good idea to make sure there is a little slack in the harness to prevent engine vibration from damaging/breakingawireon the connectors. 6. Be sure to check the wires are not indirect contact with any sharp edges, exhaust and/or other objects, which could result in long term wear and/or damage. 7. Connect the TFI ground lead to the negative terminal of the battery along with the factory ground lead. 8. With the rubber plug removed from the TFI, turn the motorcycle key switch to the “ON”position. As the bikes electrical system goes through initial startup mode you may see LED’sflashingonthe TFI.

Incoming search terms:

HONDA GL1500 Headlamp Adjustments Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
Headlamp Adjusting Procedure Tools needed • Long, slender #1 Phillips screwdriver (for adjusters behind the rubber plugs) • #2 Phillips screwdriver (for the other adjuster screw) • 12-inch square of cardboard • Flat wall or garage door • Paper, tape, marker NOTE: All adjustments are very fine. You have to turn the screws A LOT to see changes in adjustment. This procedure is best done after dark, because you will need to do some test rides. Preparation 1. Set the bike on its center stand, 10 feet away from an unobstructed wall or garage door, and square to the wall or door. 2. Remove the front fairing cover and lower vent grille to gain access to the headlamp adjusters. 3. Idle the engine or connect a battery charger to the battery, to prevent battery drain. Headlamp assembly viewed from the front, showing positions of mirrors and adjusters (pretend the lens has been removed) . Low Beam Vertical Alignment 1. With the lights on low beam, cover the right half of the lamp assembly with the cardboard square, so only the left bulb is shining on the wall. 2. Using a marker, mark the top of the left low beam on the wall (use paper taped to the wall if you don’t want to mark the wall itself) . 3. Move the cardboard so it blocks the left bulb, so only the right bulb is shining on the wall. 4. The top of the right low beam should be even with the mark you made for the left low beam. If it’s not, adjust by turning the screw behind the rubber plug at the top of the lamp assembly, using a long, slender #1 Phillips screwdriver. 5. Move the cardboard back and forth between the bulbs to verify that the low beams are at the same height. On high beam, the two hotspots should line up vertically. High Beam Vertical Adjustment 1. With the lights on high beam, note the position of the beams’ hot spots on the wall in relation to the mark you made in step 5 above. 2. Most owners complain about their low beams being too low on the roadway. To correct this, lower the high beams by turning the screw behind the rubber plug at the bottom of the headlamp assembly, using a long, slender #1 Phillips screwdriver. You can watch the high beam hot spot being lowered on the wall in relation to the mark you made. 3. Take a test ride. Get out on a dark street, and adjust the high beams using the dash knob until you like what you can see. Then switch to low beam and see how that looks. 4. Repeat these steps until you get the low beam pattern you want. Left/Right Adjustment 1. Back to the wall. Set the bike on its center stand at a distance of 25 feet from the wall and square to the wall. Center the front wheel. 2. Shine the high beams on the wall. 3. Step to the back of the bike, and level your eye with the center of the passenger backrest. Use the center of the backrest and the center of the windshield like a gunsight. The center of the hotspot of the high beam should hit the wall in this line. 4. Adjust by turning the uncovered screw at the bottom of the headlamp assembly, using a #2 Phillips screwdriver.

Incoming search terms:

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON ROAD ZEPPELIN SEAT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse following the instructions in the service manual. NOTE Cover the painted surfaces with protective material to prevent scratches or other damage. 2. Remove the left and right side saddlebags following the instructions in the owner’s manual. 3. See Figure 1. Remove the screw (1) and lockwashers (2) securing the grab strap (3) to the bracket (4 or 6). Save the hardware for installation. 4. Remove the grab strap. 5. Remove seat following the instructions in the service manual. -J04456 1 of 4 1 2 4 3 1 2 6 3 5 7 is06068 1. Stock screw 2. Stock lockwasher 3. Grab Strap 4. Bracket, 2009-Later Models 5.2009-Later Models 6. Bracket, 2008-Earlier Models 7.2008-Earlier Models Figure 1. Grab Strap and Saddlebag Front Mounting Bracket INSTALLATION 1. See Figure 2. Remove rubber plug from accessory connector (1) located under seat. Plug the seat electrical connector into the accessory connector. The connectors should lock together with an audible click. 2. Position the seat on the frame. Make sure the electrical harness and connector are not pinched between the seat and frame. 3. Install the seat following the instructions in the service manual.

Honda VTX1800F Left/ Right Floor Board Assembly Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
1. Unplug the horn wires. 2. Unbolt the left side foot peg bracket assembly and save the hardware, the stock bolts will be used to install your new Cobra floorboards. 3. Remove horn and the shift lever from the stock mount and install onto the new Cobra mount the same way they were on the stock mounts. Install the 8mm acorn nut on the exposed threads from the shift lever bolt. 4. Bolt the Cobra floorboards to the motorcycle using the stock bolts and torque to factory specifications. Note: Make sure shift lever operates properly and that there is adequate clearance. Right Side 1. Remove chrome cover from the top of the rear brake master cylinder by removing the two nuts on top. 2. Remove brake lever return spring and the stop light switch spring. 3. Remove rubber plug from the center of the brake lever pivot bolt then remove the bolt. 4. Remove the two bolts that hold the master cylinder and brake light switch/chrome cover mount. 5. Unbolt the right side foot peg bracket by removing the two stock 10mm bolts and save the hardware, the stock bolts will be used to install your new Cobra floorboards. Note: look at the placement of the large spacers behind the foot peg bracket they will need to be re-installed in the same position. Also note the nut on the inside of frame rail for lower bolt. 6. Install the Cobra floorboard using the stock bolts and spacers removed in previous step. 7. Remount the master cylinder and brake light switch/chrome cover mount removed in step 4 the same way it was on the stock mount bracket, reuse stock hardware. 8. Install the brake lever using the stock pivot bolt & rubber plug that was removed in step 3

Victory Electronic Jet Kit Installation Instructions

0

Filed Under (Victory) by admin on 31-10-2010

download
INSTALLATION ( at anytime during install or tuning please callus for any and all help, we can’thelpifyoudon’tcall ) 1. Before installing the TFI you must first disconnect the negative lead from the battery. 2. Determinea location for the TFI unit. Suggested locations areas follows: Under the seat, behinda side cover or tail section. 3. The TFIcomeswitha harness with injector connectors that match the factory injector connectors. 4. Locate the factory fuel injectors (see owners manual if you are not sure)*. If the TFIharness does not match your injectors do not proceed and call tech support at 877-764- 3337. 5. Disconnect the factory injector connectors from the fuel injectors and replace with the TFI injector connectors from the TFI unit, basically unhook the factory injector connector and plug the matching TFI connector (female) to the injector and then connect the factory injector connector to the TFI connector that simulates the injector (male). There is no order to hookup the TFI harness to the factory harness just make sure the original factory connector goes toits’original cylinder. It is a good idea to make sure there is a little slack in the harness to prevent engine vibration from damaging/breakingawireon the connectors. 6. Be sure to check the wires are not indirect contact with any sharp edges, exhaust and/or other objects, which could result in long term wear and/or damage. 7. Connect the TFI ground lead to the negative terminal of the battery along with the factory ground lead. 8. With the rubber plug removed from the TFI, turn the motorcycle key switch to the “ON”position. As the bikes electrical system goes through initial startup mode you may see LED’sflashingonthe TFI.

Incoming search terms: