Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Incoming search terms:

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

HONDA GL1800 LED LIGHTED FRONT FENDER EAGLE INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 03-03-2011

download
GL1800 LED LIGHTED FRONT FENDER EAGLE Note: Read instruction thoroughly before installing. Drilling required. 1. Place bike on center stand. 2. Remove front fender. 3. Measure from the tip of the front fender towards the bike 3 inches and mark. 4. Center eagle on fender and mark fender for drill location under the eagle head. 5. Drill a 1/8″ hole. 6. Clean area. 7. Put the light wires through the hole and secure the wires to inside of fender so wires will not touch any moving parts. 8. Remove the tape covering from the light and press on firmly. 9. Replace fender. Attach the black wire to ground and red wire to a running light

Incoming search terms:

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly

Incoming search terms:

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

Incoming search terms:

1969-1978 BMW Motorrads LED Blinker Conversion Kit Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Disassemble all 4 blinker light assemblies as shown in Figure 2 to start the installation. Be sure to remove the lens, gasket, and bulb/reflector assembly completely. Be sure to remove the wires from the reflector assembly prior to removal from the housing. The reflector assembly will not be used any further, keep in a safe place to be stored, if desired. Figure 3 2. Figure 3 (left) shows the function with their labels on the screw terminal block locations. If planning to use the “Running Light” feature, an additional wire might be needed to be installed to use this option. If you desire to use the “Running Light” function of these LED Boards, please refer to section “How to Use the Running Light Feature of the CD1007s”for complete instructions. 3. Pull out the existing wires far enough so that they can easily reach the terminal block. Insert the correct wire in the correct location of the terminal block. Using a jeweler flat-blade screwdriver, tighten the screw to secure the wire in its location. It is highly recommend to keep the terminal block to end of the signal housing facing outward of the motorcycle, as illustrated in Figure 3 (right). Model: CD1007, LED Blinker Conversion Kit Installation Instructions For 1969-1978 BMW Motorrads: Disclaimer: Under no circumstances will Bulbsthatlast4ever or it’s representatives be responsible or liable for any incidental or consequential property damages or personal injuries arising from or in connection with the use or installation of any of the listed foregoing products or devices. Rev. 6/10 Figure 4 4. Install the screws into the lens, then place an o-ring over each screw, as illustrated in Figure 4 (left & right). The o-rings will prevent the LED Board from moving around due to vibration

Incoming search terms:

Incoming search terms: