Harley-Davidson FXWG, FXST (all except FXSTS), FXDWG Light Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2012

download
1. Put a pair of male and female clamp halves together just above the lower triple-clamp. Squeeze the ends of the clamp together with a pair of pliers. Diagram A. 2. Have an assistant position the Light Bar Assembly so the lightbar bracket is to the outside of the clamp assembly. Make sure the wires from the Light Bar Assembly are below the lower triple clamp. Diagram B. 3. Insert a Screw through the clamp and Light Bar Assembly mounting bracket and thread on an Acorn Nut. 4. Hold the Light Bar Assembly in place in front of the lower triple clamp, assemble and attach the remaining clamps. 5. With all four clamp assemblies in place, tighten the clamping screws and nuts to 15 ft. lbs. (21 Nm). Refer to the service manual to gain access to the wire harness inside the fuel tank tunnel or inside the frame backbone. Also, verify the appropriate color wires for hook-up of the passing lamps and turnsignals and running lights. Route the wires from the Light Bar Assembly, around the lower triple- clamp, and up to the frame backbone. Secure the wires so they cannot become pinched when turning the fork. A. The short black wires from the Light Bar Assembly connect to the wires powering the running lights. B. The short red wires from the Light Bar Assembly connect to the wires powering the turnsignals. C. The long blue wires from the Light Bar Assembly connect to the wire powering the headlight low beam. After the wires are connected, verify the operation of the passing lamps, running lights and turnsignals. Correct any connection problems before reassembling the motorcycle. Reinstall the fuel tank. Check all fasteners used during this installation for tightness

YAMAHA ROADSTAR TRIKE Removal of Clear Taillights and installation of Red Taillights

0

Filed Under (Yamaha) by admin on 16-02-2011

download
1 Installation of Lights 1.1 Support the trike on jack stands and remove the wheels. 1.2 Remove the clear lights from the inside of the wheel wells by unscrewing the three (3) screws from the light. 1.3 Unplug the wires and remove the lights. 1.4 Remove the chrome bezels and rubber gaskets from the clear lights and install on the red lights (5 screws). 1.5 Re-connect the wire plugs and install the red lights to the trike body using the same three screws. 1.6 Replace the wheels and torque the lug nuts to 75 lb.ft. 2 Wire modification inside trunk 2.1 From the inside of the trunk pull back the carpet on both the left and right hand sides to expose the wire harnesses coming from the wheel wells. 2.2 Locate the resistors in the harness, 2.5″ x 0.5″ x 0.5″, and covered by black shrink wrap. 2.3 Cut the shrink wrap to expose the resistors and cut wire on both side of the resistors. Remove and discard resistors. 2.4 Splice in the supplied 5″ green wires (WITHOUT the diodes) with 2 blue scotchlock connectors per side to reconnect the cut wires. 2.5 Do not glue in carpet until lights are tested. 3 Change to pigtail from Trike to Motorcycle. 3.1 Remove driver’s sear 3.2 Unplug pigtail from motorcycle (MC) wiring and trike body wiring. 3.3 Cut heat shrink on the MC plug side of the pigtail and pull expansion sleeve back to expose the wires. Figure 1 3.4 Cut Green and Yellow turn signal wires and about 3″ from the MC plug and splice in Green and Yellow wires from the supplied resistors with the supplied hest shrink solder connectors (heat to be applied) – (three wires in one connection) Figure 1 3.5 Cut the Red (Brake) and Brown (Running lights) wires and splice in the supplied diodes with the supplied heat shrink solder connectors. Red side of the diode wire facing the Trike plug. Figure 1 3.6 Connect eye lug on the black wire from the resistors to the negative terminal of the battery. Figure 2 3.7 Plug pigtail back into the Trike body and the MC

Incoming search terms:

HARLEY-DAVIDSON LARGE LED SILVER BULLETS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
PROCEDURE STEP 1*Remove the stock turn signal fixtures and cut the wires in a convenient and inconspicuous splice location. STEP 2**Place the split lock and flat washers on to the hollow bolts as shown in PIC. 1. Run the power leads through the hollow bolts and assemble the Silver Bullets to their mounts. See PIC. 2. STEP 3*Install the new Silver Bullet assemblies to the Mount Bar on the motorcycle. The stock 10-24 x 1/2″ socket head screws are to be re-used. PROCEDURE fOR AMBER DUAL CIRCUIT (fRONT WIRING) LED SILVER BULLET WIRE COLOR CODING IS AS fOLLOWS: Black — Ground Blue — Running Lights (power) Violet — Turn Signal (power) STEP 1 Turn key on. Test OEM stock front turn signal wiring with test light. STEP 2 Locate and mark the running light (power) wire. STEP 3 Individually activate the turn signals and mark the side-appropriate wires. STEP 4 Use the color code above to solder/connect the corresponding Silver Bullet wires to your Join like colored wires on the Silver Bullets and the bike’s turn signal harnesses. Insulate your connections. Route the wires safely out of harms way and tie the wires in place with nylon cable ties. 1995-EARLIER MODELS With a test light, probe the two black wires leading to each of the stock front turn signals. On each side, the wire that has power only when the turn signal button is depressed is the turn signal positive wire. The wire that is “hot” constantly when the key is on is the running light wire. Connect the violet wire from the Silver Bullet to the bikes turn signal wire, and the blue Silver Bullet wire to the bikes running light wire. Connect the black wire from the Silver Bullet to a known good chassis ground (bare metal). Insulate your connections. Route the wires neatly out of harms way and secure them with nylon cable ties. When replacing stock incandescent turn signals with LED lights, it may be necessary to add a load equalizer to make the turn signals flash properly. NOTE: When using Amber Dual Circuit Silver Bullets in rear applications, blue running lights (power) wire will not be used. To avoid corrosion, tape off bare wire. Test the lights for run and flash functions. If they light, but do not flash in the turn mode, add the load equalizer. The load equalizer has one black and two violet wires. The violet wires are not side specific. NOTE: LED Turn signals require the use of one Load Equalizer PER PAIR OF LED TURN SIGNALS to achieve the proper flash function. It is perfectly normal for the equalizer to get warm (about 140 degrees) during turn signal operation.

Incoming search terms:

SUGGESTED WIRING FOR DL35 HI/ LOW DRIVING LIGHTS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
CHASSIS GROUND DRIVING LIGHT WHITE/LOW BROWN/PARK BATTERY 86 85 87 30 86 87a HEAD LAMP HEADLAMP/LOW HEADLAMP/HIGH SUGGESTED WIRING FOR DL35 HI/LOW DRIVING LIGHTS AMP RELAYS 30 TO FRONT SIGNAL RUNNING LIGHTS OR ANY WIRE THAT HAS POWER WITH IGNITION ON BLUE/HIGH DRIVING LIGHT BLUE/HIGH BROWN/PARK WHITE/LOW 30A FUSE 85 30 87 87a SWITCH

SUZUKI M109 TURN SIGNAL RELOCATION BAR

0

Filed Under (Suzuki) by admin on 21-12-2010

download
1. Remove the windscreen/headlamp assembly by removing the two (2) 4mm allen screws located on the sides of the windscreen and the two plastic rivets at the top rear (push the center pin inward º” and then pull the rivet out). Pull the windscreen/headlamp forward to gain access to the rear, unplug the headlamp and set aside. 2. Locate the turn signal wire connections and unplug them from the wire harness. On the black connectors lift the tab up to unlock the connector and on the white ones use a small screwdriver inserted into one of the two longer slots and lift the center portion up while pulling the connector apart. Remove the screws which attach the turn signals to the chrome signal mounts located on the bottom of the mounts. Pull the turn signals out from the mounts and set aside. Looking thru the hole in the mount that the turn signals were in you will see a 4mm allen screw on each side, remove these. Remove remaining two (2) 6mm allen screws located on the bottom of the steering head that attach the mounts, remove and set aside. 3. Lay out the new turn signal mounting bar (see photo). Install the signals onto the bar as shown routing the wires thru the bar and out thru the slot in the center. Install the two (2) 6 x 8mm screws supplied and tighten securely. 4. Install the bar/signal assembly onto the steering head using the two (2) 6mm allen screws removed earlier (the brake hose clip should be on the bottom below the signal mount) and tighten securely. 5. Reconnect the turn signal wires (the pale blue/green wire goes to the right signal). Turn the ignition on and test the functions of the signals and running lights. Re-install the windscreen/headlamp assembly being sure to first plug in the headlamp

VENTO PHANTOM R4i USERS MANUAL And Specifications

0

Filed Under (Vento) by admin on 02-11-2010

download
LEFT HAND CONTROLS Horn button – Press the switch to sound the horn Turn signal switch – Slide switch left when turning left, slide switch right when turning right and push in to cancel. Low beam / High beam Switch For High beam Turn upwards / For Low beam Turn downwards. Engine Kill Switch Turn into the X position to shut off. Turn into the O position to start the engine. RIGHT HAND CONTROLS Headlights / Running Lights – Slide switch towards the left up to first level and running lights will come on; slide once again to the next level the head lights will turn on. Electric Starter button – Press the electric starter button for a maximum of 5 seconds. NOTICE: If the engine does not start the first time, try again after 30 seconds. DO NOT use the electric starter after long periods of inactivity, doing so can drain the battery. IGNITION SWITCH 1. ON Position (Engine Ignition) Engine can be started Electrical devices such as horn, lights, etc. can be activated. Key cannot be removed. 2. OFF (Engine Shut-off) Engine cannot be started. Electrical devices such as horn, lights, etc. are inoperable Keys can be removed 3. LOCK Position Steering lock is engaged Engine cannot be started. Electrical devices such as horn, lights, etc. are inoperable Keys can be removed NOTES: Rotating the key switches the electrical circuitry ON and OFF WARNING: Do Not Turn the ignition key when the engine is running. Use the kill switch to shut-off, then rotate the key counter-clockwise towards the OFF position. NOTICE: If the engine is shut-off, please turn the ignition switch to the OFF or LOCK position. Failure to do so can cause battery drain or damage on the electrical system. STEERING LOCK OPERATION For your protection, activate the steering lock when leaving your vehicle parked or unattended. 1 . Turn handle bar to the left or right limit. 2 . Turn the key from OFF towards the LOCK position. 3. Remove the key. To unlock: Insert the key and rotate it to the OFF or ON position

Incoming search terms: