Yamaha 1998-2001 YZF-R1 Installation Instructions (Slip on system)

0

Filed Under (Yamaha) by admin on 16-02-2012

download
Remove the lower fairing. 2. Remove the existing exhaust system from the EXUP valve rearward (EXUP valve is retained). Save the stock exhaust clamp for reuse. 3. Inspect the exhaust gasket. Replace if necessary. 4. Install the S-Bend to the rear of the EXUP valve, make sure the system fits flush. Reuse the stock exhaust clamp to connect the S-bend to the valve. 5. Install the TiForce end can to the S-bend tail pipe. 6. Loosely attach the two rubber bands, stainless steel bands (K), and stay to the end can using the supplied 6mm hardware (H) and the hanger / stay arm (G). (See figure 1) . 7. Place the bands approximately 180mm from the edge of the end can. (See figure 2) . 8. Using the stock provided mounting point on the passenger foot peg, use the M10x45mm bolt and hardware to mount the end can loosely, allowing for some adjustment. 9. Carefully align the two stainless bands so that they are parallel to each other, and spaced properly on the can. Tighten the 6mm hardware (H). Make sure that the rubber pads fully cover the bands (K). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 10. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 11. Attach the supplied springs to secure the end can to the S-bend pipe. Make sure the exhaust system is free and clear of the bike. If necessary, adjust for proper clearance. 12. Go back and tighten all fasteners. 13. Check that all fasteners are tightened per specifications, then start the motor and check for exhaust leaks. 14. Reinstall the fairing lowers.

BMW K1200 RS/ GT Full Exhaust System Full Exhaust System Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the side- stand or ideally a rear service stand. 2. Remove the lower fairing. 3. Unscrew the O 2 sensor. Remove the stock exhaust system at the rear canister support bracket and where it bolts to the engine. CAUTION -the stock exhaust is very heavy, be careful not to drop it! Also, be careful not to damage the engine sensor located near the front header pipe. 4. Pry out the old exhaust port gaskets and replace with new BMW OE (x4) exhaust port gaskets. Adab of grease will help hold the gaskets in place while you work. 5. Coat the exhaust studs and O 2 sensor threads with high temperature anti-seize compound. 6. Install the TBR headers into the exhaust ports making sure to get a good seat onto the exhaust port gaskets. Next, install the header nuts starting at the rear/outside stud and working your way forward on the outside set of studs. Once that is finished repeat along the inside set of studs. Tighten header nuts only finger tight at this point. 7. Be sure to coat the threads of the sensor with the included packet of hi-temp anti-seize. Install the O 2 sensor into the TBR headers. Turning the sensor in the counterclockwise direction a few times then screwing it clockwise to install will help make it easier to install and prevent the wire from binding. 8. Place a bead of the hi-temp sealant on the outside edge of the headers that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 9. Carefully slide the muffler clamp over the muffler. ( Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) Attach it to the canister support bracket using the stock BMWhardware. Both tabs of the canister clamp should be located on the inside of the canister support bracket. Leave loose for the moment. 10. Make sure everything is lined up and start to evenly tighten up the header nuts to BMWfactory torque specification. Tighten the canister support hardware and install the springs as well. 11. Start the bike and check for leaks around the exhaust ports and the header/canister junction. 12. Reinstall the lower fairing

Incoming search terms:

Aprilia Mille And Mille R Exhaust System Installation Instructions

0

Filed Under (Aprilia) by admin on 26-10-2010

download
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or ideally a service lift. 2. Unhook the springs holds the stock canister to the headers under the bike. 3. Remove the hardware that holds the stock canister at the exhaust bracket. Take off the stock canister. 4. Install the new s-bend into the stock header. 5. Install VALE adapter kit using supplied kit instructions. 6. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the TBR canister onto the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out. 7. Carefully slide the muffler clamp over the muffler. (Note: The stainless steel canister clamp and the name badge on the canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the outside of the exhaust bracket. Use the stock hardware to secure it. Leave loose for now. 8. Make sure everything is aligned and tighten all hardware. Reinstall the stock springs at the s-bend/header junction. Affix the two connector springs to the muffler. 9. Before you run the bike, clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike. This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness