Kawasaki Voyager 1700 Hitch Removal both saddlebags and Installation Instructions

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
Remove the seat. Remove both saddlebags by removing the 3 bolts shown below Remove the plastic liner in the bottom of the trunk by gently pushing in on the center of the plastic clips Once the liner is removed remove the trunk rear light assembly by removing the 4 black screws in side the trunk and 4 on the bottom side of the light assembly. Unplug the light assembly and set it aside. Remove the bolts for the trunk Have a friend hold the trunk up and remove the 4 screws (two on each side) for the side trim Put the bolts back inside the trunk and tighten finger tight to make sure it does not fall. Remove the remaining side trim screws, 5 on each side, and remove the side trim and set it aside Remove 2 bolts from the saddle bag supports. Place the side plate mounting bracket behind the saddlebag supports and replace the two bolts you removed in the previous step. (We recommend using a few drops of Loctite). Do this step for both sides of the bike. Place the side plate behind the mounting bracket and attach the side plates to the mounting brackets with the two bolts supplied with the hitch (We recommend using Loctite on this step) Repeat this step for both sides of the bike

Incoming search terms:

VT 1100 TEARDROP SPECIFIC-FIT SADDLEBAGS INSTALLATION

0

Filed Under (Honda) by admin on 23-11-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

Honda VTX1800F, VTX1300C, VTX1800C Plated Saddle Bag Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Instruction Manual > Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Place the supplied spacers in the recessed holes on the fender rails (large spacer to the front, small spacer to the rear). 3. Install your Cobra saddlebag supports using the supplied button head bolts (where the stock bolts were removed) the saddlebag supports should hang towards the rear and away from the motorcycle. 4. Torque bolts to factory specifications. Note: If using Cobra sissy bar mount the saddlebag supports over the sissy bar brackets and do not use supplied spacers. Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

Incoming search terms: