HARLEY DAVIDSON FLSTC SOFTAIL SADDLEBAG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Additional Fitment Information Detachables NOTE If motorcycle has not been altered from fixed saddlebag hardware to accessory mounting detachable docking points. the separate purchase of Turn Signal Mounting Bar (Part Number 68611-98) is required for sufficient lock clearance. This kit is available at your Harley-Davidson Dealer. Installing these saddlebags on models equipped with a detachable sissy bar or detachable luggage rack requires the additional purchase of mounting hardware kit as follows: Hardware Kit Fitment 53075-03 2003 and later FLSTC models with detachables 53009-03 1987 through 2002 FLSTC models with detachables See Service Parts Page for kit contents. Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (3.18Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Wide Tire If a wide tire kit has been installed, utilize the hardware and installation instructions found in that kit to reorient the fasteners to come from the inside to the outside of the finder. Button head screws from wide tire kit must be installed from the inside out, with the button heads on the inside of the fender. Failure to do so could result in bolt contacting tire, which could result in death or serious injury. Installation NOTE A Service Manual for your vehicle is available at your Harley-Davidson Dealer. 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect the negative (-) battery cable first. If positive (+) cable should contact ground with the negative (-) cable connected, the resulting sparks may cause a battery explosion which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Following instructions in applicable Service Manual, remove original saddlebags from supports. Install Turn Signal Mounting Bar If motorcycle is not equipped with accessory mounting detachable docking points, install Turn Signal Mounting Bar (Part No. 68611-98) following instructions provided with the kit. See Figure 1

Incoming search terms:

ARLEY DAVIDSON FLHTCUSE HEATED SEAT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION 1. For 2006 and later FLHT/I/C/CI/CUI, and ALL FLTR models: a. Follow the instructions in the Owner’s Manual to remove the left-side and right-side saddlebags b. Remove the bolts and flat washers to remove the passenger grab strap and saddlebag front mounting brackets from the chrome frame tube covers. c. Remove the passenger grab strap. 2. ALL models: Follow the instructions in the Owner’s Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Follow the instructions in the Owner’s Manual to remove the negative (-) battery cable from the battery. 4. See Figure 1. Identify and remove the plug from the accessory circuit connector [4] in front of the battery

HARLEY DAVIDSON DYNA REAR AXLE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Models This kit fits 2006 Dyna models. This kit does not fit on motorcycles equipped with saddlebags. Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Place axle covers in position over ends of swingarm with the deeper cover on the left side (covering the axle nut). 2. Fasten the clamping bars (3) to the backs of the covers using hex-head screws (5) and Belleville washers (4), securing the covers to the swingarm. Tighten the hex-head screws to 21-27 in-lbs (2.4-3.0 Nm) . Do not overtighten SERVICE PARTS 4 1 3 4 5 2 3 5 is00709 Figure 1. Service Parts: Dyna Swingarm Axle Cover Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 45159-97 Washer, Bellville (4) 4 Not Sold Separately Axle cover, left side 1 3644 Screw, #10-24 x 1/2 inch (4) 5 Not Sold Separately Axle cover, right side 2 Not Sold Separately Clamping bar (2) 3

HARLEY DAVIDSON TRUNK MOUNT FLAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
Installation Water may enter Tour-Paks/saddlebags with flag mast installed during inclement weather. Attaching a flag mast to a Tour-Pak or saddlebag without wear pads in place may result in damage to the Tour-Pak or saddlebag exterior. Periodically check to ensure the flag mast remains in contact with wear pads. 1. See Figure 1. Remove adhesive backing from wear pad and place on area where mast base will hit the painted portion of the Tour-Pak and/or saddlebag. Attach flag mast to Tour-Pak or saddlebag as shown. Attaching flag mast to Tour-Pak or saddlebag without rubber pads in place may result in damage to exterior of Tour-Pak or saddlebag. 2. Cut the self adhesive rubber pad in half. Remove the backing from the rubber pads and place on the inside of the Tour-Pak or saddlebags on each side of the flag mast as shown. CAUTION CAUTION CAUTION INSTRUCTIONS -J01143 REV. 11-20-01 TRUNK MOUNT FLAG KITS ® Kit Numbers 94612-98, 94617-98, 94618-98, 94626-98 Figure 1. Flag mast installed on Tour-Pak Place wear pad on area where mast base will hit the painted portion of the Tour-Pak and/or saddlebag i01121 Figure 2. Rubber pads installed on interior of Tour-Pak

HARLEY DAVIDSON CHROME SADDLEBAG COVER WINGTIP TRIM KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Installation NOTE The following procedures can be performed with the saddlebags on or off of the motorcycle, and the covers on or off of the saddlebags. Figures show saddlebag covers removed. 1. Open the saddlebags and remove all loose contents. 2. Thoroughly clean the left and right saddlebag covers, and let them dry completely. 3. See Figure 2 for your saddlebag material. Position a straightedge against the check strap mounting posts of one of the covers, and mark or scribe a guide line along the straightedge as shown. NOTE When applying the templates in the following steps, make sure the templates are aligned as instructed, and the respective “LEFTSIDE” or “RIGHTSIDE” lettering is clearly readable when applied to the applicable (left or right side) cover. The templates are designed to be easily removed from the first cover and re-applied to the remaining cover When applying the templates, ensure that each template is correctly positioned BEFORE drilling the first hole

HARLEY DAVIDSON NOSTALGIC SADDLEBAG GUARD RAILS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL 1. If desired, remove the saddlebags. 2. Remove screws (C) and locknuts (D). Save for installation. 3. Remove reflectors with fishing line or dental floss. Use a sawing motion to remove the adhesive. Clean the surface thoroughly with an equal mixture of isopropyl alcohol and distilled water. Allow the surface to dry thoroughly. INSTALLATION 1. See Figure 1. Position the correct saddlebag guard rail (1 or 2) over the saddlebag guard and support assembly (A). Loosely install the screw (C) through the saddlebag-to- fender support bracket (B), through the saddlebag support (A) and through the inner hole of the saddlebag guard rail bracket. Install nut (D). Tighten finger-tight. NOTE Position the saddlebag guard rail as low as possible on the stock saddlebag guard and support assembly. 2. Install screws (6) and washers (5) through the clamp end of the saddlebag guard rail. Position clamp end around the upright of the saddlebag guard and install the clamp (3 or 4). Tighten screws finger-tight. 3. Align the saddlebag guard rail (1 or 2) parallel to the bottom of the saddlebag and muffler. Tighten the cap screw (C) and locknut (D) to 15-20 ft-lb (20-27 Nm) . 4. Tighten the clamp screws (6) to 22 in-lb (2.5 Nm) . NOTE The reflectors are location-specific. There are markings on the back of the reflector – “L BOTTOM” or “R BOTTOM”. 5. Peel the backing from the base of the new reflector (7 or 8). Without touching the reflector to the saddlebag guard, position the reflector and press the reflector to the saddlebag guard above the clamp (3 or 4) and press for 30 seconds. After releasing pressure, avoid direct contact with the reflector for at least 20 minutes. 6. Repeat all steps for the other side of the motorcycle. NOTE For ease of use, move the saddlebag buckles to the highest hole on the strap. 7. Install the saddlebags, if removed

HARLEY DAVIDSON DETACHABLE TOUR-PAK LIGHT HARNESS KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. ALL models: Install the Detachable Tour-Pak Rack Kit per the instructions in that kit, up to the point where the saddlebags are to be re-installed. NOTE Make note of the cable strap locations before releasing the harness from the upper frame tube. New straps will be fastened in the same location. 3. Cut the larger cable strap fastening Tour-Pak circuit [12] (see the Service Manual Wiring Diagram) of the vehicle main harness to the left-side upper frame tube, rearward of the shock absorber. Cut the small cable strap at the end of the circuit [12] conduit. 4. Slit the conduit open along its length to expose the final ten inches (0.25 M) of main harness circuit [12] wiring. Cut the three wires (Black, Blue, and Red with Yellow tracer) nine inches (0.23 M) from the three-way Multilock socket housing [12B]. The socket housing and cut wires can be discarded. 5. Obtain the socket housing, secondary lock (locking wedge), and three socket terminals from the kit. See the illustration at DEUTSCH ELECTRICAL CONNECTORS: REMOVING/INSTALLING SOCKETS in the Service Manual. Refer to CRIMPING INSTRUCTIONS in the Service Manual, and follow the instructions to install the terminals to the three wire leads of main harness circuit [12]. 6. Per the instructions under DEUTSCH ELECTRICAL CONNECTORS, insert the Blue lead and terminal into Cavity 1 of the new socket housing. Insert the Red/Yellow lead and terminal into Cavity 2. Insert the Black lead and terminal into Cavity 3. 7. Cut the excess conduit from main harness circuit [12]. 8. Obtain the two cable straps from the kit. As noted in Step 3, use one strap to bind the end of the main harness circuit [12] conduit. Use the second strap

HARLEY DAVIDSON FLSTN SADDLEBAG GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL EXTENDED REACH CONTROLS KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
PREPARE THE MOTORCYCLE 1. For models equipped with saddlebags: Remove the saddlebags following the instructions in the appropriate Service Manual. 2. Remove the seat following the directions in the Owner’s Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect the negative battery cable. 4. Secure motorcycle in upright position. NOTE This kit is not compatible with engine guards. 5. If the engine guard is present, remove and discard it. LEFT SIDE Component Removal 1 3 4 2 7 5 6 8 2 is05048 1. Pretzel clip 2. Bushing (2) 3. Screw (6) 4. Jiffy stand bracket 5. Bumper 6. Jiffy stand leg 7. Clevis pin 8. Spring Figure 1. Jiffy Stand 1 2 3 5 4 is05053 1. Jam nut 2. Shifter rod end 3. Acorn nut 4. Shifter rod 5. Shifter arm Figure 2. Shifter Linkage 1. For HDI Vehicles: Remove the left side foot control support, and jiffy stand sensor, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. For all other models: Remove the left side foot control support, jiffy stand and spring, shifter linkage, shift lever and footpeg following the instructions in the appropriate Service Manual. NOTE Two bearing sleeves will remain inside the footrest bracket. The extended controls bracket from the kit will include two sleeves pressed into the bore of the shift lever arm support. 2. Remove rod ends and jam nuts from the shifter rod. Save the rod ends and jam nuts for installation. Component Installation 1. See Figure 9. Select shifter mounting assembly (6), O- rings (5), nylon washer (4) and the shift rod (1) from the kit. 2. Install the shift arm and new O-rings in the bracket. 3. Apply LOCTITE 243 Threadlocker and Sealant to the three mounting screws and mount the shifter bracket with shift arm to the frame. Tighten the mounting screws to 25-30 ft-lbs (33.9-40.7 Nm)

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

Incoming search terms: