Street Magic Magical Wizards LED Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Always wear appropriate safety gear including safety glasses when soldering or performing any electrical work. It is highly recommended that safety glasses be worn throughout this installation process. Temperature of bike must be at least 60 degrees F. for tape to properly cure. Read all directions before starting project. 2. Turn fuel supply valve to off position before starting. Be sure bike is on level surface and secure and cool. 3. Important: Disconnect negative battery cable from battery; refer to owner’s manual. Failure do to so may result in electrical shock, injury, or fire. Secure negative battery cable away from positive side of battery and all other positive voltage sources on bike. 4. Select hidden locations to mount LED Accent Lights to provide best coverage. 5. Remove fuse from fuse holder. 6. Clean mounting locations on both motorcycle and accent lights with 3M promoter, promoter sponge will dry up quickly, place sponge in sealed plastic bag when not in use. Do not touch 3M promoter with bare fingers. 7. Place piece of double sided tape on accent light if needed, lights come pre-taped on back surface. Trim excess off sides with razor blade. Carefully remove backing from double sided tape and place light on selected mounting location. Press firmly and hold for 10 seconds. Repeat for all lights to be mounted on bike. 8. Route wires from accent lights back to central points near battery compartment under seat. Route wires such that they not interfere with normal operation of bike. Cut off any excess wires, strip back insulation as required. 9. Select several locations to secure wires to frame. Secure wires using tie wraps provided. 10. Join all black wires from LEDs into one Cage Clamp Connector #1. Join all Red wires from LEDs into Cage Clamp Con- nector #2, Join all Blue wires from LEDs into Cage Clamp Connector #3, Join all Green wires from LEDs into Cage Clamp Connector #4. 11. Connect Orange wire from the remote control wire harness to the Red Cage Clamp Connector, connect Blue wire from remote control wire harness to Blue Cage Clamp Connector, connect Green wire from remote control wire harness to Green Cage Clamp Connector. Connect White wire from remote control wire harness to Black Cage Clamp Connector. 12. Crimp spade connector on ends of remaining Red and Black wires from Remote Wiring Harness. Heat spade connector with heat gun so that it shrinks around wire. 13. Connect Red Wire to Positive (+) side of battery, and Black Wire to (-) Side of battery. Take necessary precautions when making connection and refer to bike’s owner’s manual. DO NOT allow any tools to touch both positive (+) side of battery and any metal surface on bike as it will cause a short which could result in serious injury and damage to the battery or other electrical circuits.

Baja DR70 Dirt Bike OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 25-11-2010

download
Before Starting the Engine/Motor 1. Engine oil level a) Check for leaks b) Tighten filler cap securely. c) Add oil if required. 2. Fuel level a) Add fuel as necessary. b) Do not overfill (no fuel in the filler neck). c) Do not mix oil with gas. d) Replace cap tightly. e) Do not refuel a hot engine. Allow engine to cool before adding fuel. 3. Warning decals a) Make sure all warning decals are legible and securely attached. b) Replace as necessary. 4. Tires a) Ensure that both tires are in safe riding condition. b) Both tires must be inflated to the pressure indicated on the tire sidewalls. 5. Drive chain a) Check condition and tension. b) Lubricate and adjust tension as necessary. 6. Throttle a) Check for smooth operation. Make sure the throttle “snaps” back to idle. b) Check for frayed cable or damaged cable housing. Replace damaged cable. c) Check for mud, debris and ice in the throttle cable/mechanism. Clean out any contamination. 5 SAFETY GEAR A DOT approved motorcycle helmet is the most important part of you safety gear. A DOT approved motorcycle helmet can help prevent a serious head injury. Choose a helmet that fits snugly. Motorcycle dealers can help in selecting a good quality helmet which fits properly.