Kawasaki Vulcan 500 Receiver Hitch Installation Manual

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if any. 3) Remove rear riders pegs. 4) Attach front of bracket A (left side) and bracket B (right side) between rear footpeg motorcycle bracket and rear footpeg. Use new bolt provided (Bolt assortment included to accommodate some accessories) 5) Attach bracket E (left side) and bracket F (right side) to two rear fender attachment bolts. Use new bolts provided. (Bolt assortment included to accommodate some accessories) 6) Attach bracket C (left side) and bracket D (right side) to brackets E and F and to second holes on rear of hitch. 7) Attach rear of brackets A and B to BOTTOM of hitch arms 8) Tighten all bolts. Receiver hitch diagram Leveling stand screw jack installation After hitch is installed, install leveling stand screw jacks to hold motorcycle in an upright and level position in order to install or remove InstaTrike. 1) Thread right side screw jack into leveling stand bracket on bracket B and adjust leveling jack bolt out until motorcycle will be level against it. 2) Push motorcycle over from left side until right screw jack is touching floor.

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

HARLEY DAVIDSON SOFTAIL REAR LOWERING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Prepare the Motorcycle 1. Follow the Service Manual instructions to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect the negative (-) battery cable from the battery. 3. Place motorcycle on a lift and secure the front wheel. 4. Use an overhead crane or hoist attached to the frame to lift the rear of the motorcycle to allow the rear fork to pivot through its range of travel. 5. Place a screw jack under the rear wheel to support and adjust the rear fork during shock removal, installation and ride height adjustment. Be sure rear wheel is supported when removing rear shocks. If wheel is not supported rear fork can drop down, which could result in death or serious injury. (00481b) Removal 1. See Figure 1. Remove the bolt and washer (1) that fasten each of the shock absorbers (2) to the rear fork. NOTE Snap-on Tool Co. adapter, Part Number SRES 24, is necessary to gain access to the shock absorber bolts. 2. Remove the flanged locknut (6) and cup washer with grommet (5) fastening the shock absorber to the frame bracket (4) and remove the shock absorber. 3. Remove, inspect and, if necessary, replace the rubber grommets, the cup washers (5), and the bushing (3). 4. Repeat for the other shock absorber. Disassemble the Shock 1. Thoroughly clean the rear fork end of the shock, especially near the shock canister seal. 2. Support the rear fork end of the shock absorber and shock canister on the table of a press. 3. Press on the shaft to compress the spring in the canister until the keeper plate drops down away from the retaining ring.

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

Triumph America Installation Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
Secure motorcycle in an upright position. 2) Remove center stand 3) Remove saddle bags (if applicable) 4) Attach bracket A to center stand mounting point on motorcycle 5) Attach bracket D (left) / E (right) to rear fender sub-frame using new bolts provided. It may be necessary to reattach saddle bags at this point 6) Attach bracket F (left) / G (right) to rear of brackets D/E. 7) Attach bottom of brackets F/G to rear hitch plate. 8) Attach bracket B (left) / C (right) to bottom of forward hitch arms. Attach other end of B/C to top of bracket A. 9) Ensure hitch is square with motorcycle and tighten all bolts. Receiver Hitch Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded leveling stand tab on bracket A and adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Incoming search terms: