HARLEY DAVIDSON WINDSHIELD MOUNTING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
This kit contains the following items: ITEMDESCRIPTION/ QUANTITY PART NO. 1 Stud, double ended, 5/16-18 (4) 3265A 2 Bushing (4) 67621-94 3 Acorn nut, keps, 5/16-18 (Chrome) (4) 7992 Installation 1. Using a T-40 TORX drive head, remove the upper left- side chrome button-head fork screw and chrome flat washer and discard. 2. See Figure 1. Obtain a double-ended stud (1) and chrome acorn nut (3) from the kit. Thread the nut onto the NON lock patch side of the stud and hand tighten. NOTE Position the clamp so the clutch cable is to the rear of the stud. 3. Slide the clutch cable clamp (4), along with the cable, into position on the stud as shown. Assemble a bushing (2) from the kit onto the stud threads. 4. Insert the lock patch side of the stud through the headlamp nacelle and into the upper fork bracket. Tighten the acorn nut and stud to 15-20 ft – lbs (20-27 Nm). 5. Continue, one at a time, replacing the three remaining chrome button-head fork screws and flat washers with the studs, bushings and chrome acorn nuts from the kit. Tighten to 15-20 ft – lbs (20-27 Nm)

HARLEY DAVIDSON SOFTAIL CHROME LOWER BELT GUARD INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
REMOVING STOCK PLASTIC LOWER BELT GUARD 1. See Figure 1. Remove the hex head bolt (2), washer (3), acorn nut (5), hex head screw (4) and acorn bolt (8) attaching plastic belt guard to rear fork. 2. Remove the plastic belt guard. Save fasteners (2), and (4), washer (3), acorn nut (5) and acorn bolt (8) for installing new chrome belt guard. INSTALLING CHROME LOWER BELT GUARD 1. See Figure 2. Position the new chrome belt guard from kit over belt. Align the holes in guard with mounting lugs on rear fork. Install acorn bolt (9) through mounting lug and fasten to belt guard. Finger tighten only. 2. Install screw (4) with washer (5, from kit) through belt guard and fasten to threaded mounting lug. Position the guard for adequate clearance and finger tighten screw. 3. At the upper belt guard, install the original forward hex bolt (2) and original washer (3) through the upper guard (1), then through the upper hole in chrome belt guard and through mounting lug on rear fork. Secure with original acorn nut. 4. Tighten all hardware to 110 in-lbs (12.4 Nm)

HARLEY DAVIDSON CHROME CALIPER AND ROTOR COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents There are no service parts available for this kit. INSTALLATION Left Side Installation 1. See Figure 2. Assemble the wedge spacer halves (1 and 2) to the left lower caliper mounting bracket (3) with the screw (4) and washer (5). 2. See Figure 3. Install the left lower caliper mounting bracket (1) to the left fork slider by sliding the wedge spacer into the hole in the bottom of the fork slider. Tighten finger- tight. 6 3 5 3 3 4 2 1 9 8 7 3 is06000 1. Rotor cover top mounting bracket 2. Spacer (models without fender rails only) 3. Screw (16) 4. Caliper cover 5. Wedge spacer 6. Screw and flat washer 7. Lower mounting bracket 8. Caliper/rotor cover mounting bracket 9. Caliper mounting bracket Figure 1. Caliper and Rotor Cover Kit (Left Side Shown)

Balancing Honda GL1500 Carburetor Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
First pry off the plastic clip covering the screw as in the first picture. Note the type of screw used, as shown in the third picture. You must put this one back in the right place. Tip; When refitting this clip later on, a bit of Blutack or similar will stop it falling off and getting lost. Pull the L piece trim away, taking care not to break the tab shown in the fifth picture Now pry off the small black plastic cover at the rear of the running light. Blutack will be a good idea here as well when refitting the cover. The owner of this GL1500 didn’t use it and the cover on each side of the Goldwing got lost, which is why you can’t see them in the pictures. Note the type of screw used here as well, same as the one mentioned earlier. The third picture shows the two normal Phillips screws at the front of the running light, remove them. Remove the running light and pull the lower fairing panel away Remove the rubber plug from the right side fan. The adjuster screw for balancing the carbs is about 6″ behind and up, and hard to see. I removed the fan so I could get the camera in and the second picture shows the adjuster screw

Incoming search terms:

Honda GL1000/1100 starter motor Removal/ Over haul Manual

0

Filed Under (Honda) by admin on 08-04-2011

download
1. Remove the three long bolts that hold the sections together and separate them. Be careful as there are a series of flat thrust washers on each end of the armature (located in the middle section). 2. The end cap basically performs no function other than to cover the brush plate and commutator area as well as center the armature shaft in a pressed in bushing located in the end of the cap. 3. The drive end contains the reduction gearing and if need be, can be disassembled to replace the bearing. This is extremely unlikely. The shaft should turn freely and normally only requires a cleaning and grease application. If the bearing in fact needs replacing, simply remove the “C” clips on either end, drive out the bearing and reinstall with an appropriate size replacement. Any decent auto parts / industrial supply should be able to supply the correct bearing. 4. Remove the brush plate from the end of the center section by removing the screw at the one brush connection. Before removing the brushes, note that one of them has an insulating sleeve over the braided wire. The replacement must go in the same brush holder. Remove the brushes and replace if necessary and clean the brush plate. ** Brake Cleaner is a good general cleaner for this entire job. 5. Remove the thrust washers from brush plate end of the armature. Count them and ensure they go back on the correct way. 6. The end of the center section that had the drive end on it has a circular plate covering it with a short splined shaft protruding through the plate. Drive the plate out by tapping the opposite end of the section on the shaft – just lightly with a rubber hammer or piece of wood to protect the shaft. Once the plate is out, remove the armature from the section. You will find more thrust washers at this end. Make sure they go back on correctly. 7. In the center of the center section there are four large Philips screws. These hold in the field coils found within the housing. Using an “impact driver”, loosen the four screws that go around the circumference of the center section and remove them. Remove the 10mm nut for the battery connection and the accompanying fiber insulating washers. With the screws and nut removed, the entire field coil assembly should withdraw entirely from the housing. There will be four (4) metal plates that the screws mounted into come falling out. They are easily replaced into the field coils when you slide it back into the housing. Do not be alarmed that you suddenly have four loose metal parts. 8. With everything out of the housing, thoroughly clean everything using the Brake Cleaner. Although the cleaner will dry without leaving a film, it is suggested that the components be dried with compressed air. 9. Get some extremely fine steel wool (“000″ of even “0000″ is better) and gently clean the metal surfaces or bars of the armature and the commutator. Blow with compressed air. 10. Using a volt/ohmeter, test for continuity between pairs of armature bars (the long ones). There should be continuity between the pairs around the entire circumference.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL PASSENGER FOOTBOARD SUPPORT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION Remove Existing Equipment 1. Remove existing footpeg and attaching hardware. 2. Remove chrome swingarm pivot covers, if so equipped. 3. Do not remove tool box, if so equipped. Install Passenger Footboard Support Kit 1. See Figure 1. Install footboard mounts (1) and (2) as fol- lows: a. Position footboard mount and insert screw (3) through part and into footpeg mounting hole. b. Position semi-circular cutout in mount extending from side of mount around nut of swingarm pivot bolt. c. Tighten screw (3) to 45-50 ft-lbs (61-67.8 Nm). 2. Position footboard support (4) on mounting stud so that bolt hole aligns with machined groove in stud. 3. Insert screw (5) through left side in split hub of footboard support. Thread into tapped hole (right side) of split hub. 4. Tighten screw (5) to 10 ft-lbs (13.6 Nm). 5. Place spring (6) into retaining hole in footboard support. Rest ball (7) on top of spring. 6. Refer to appropriate I-Sheet for instructions to install the footrest (A) and pivot pins (8) for your motorcycle

HARLEY DAVIDSON GEAR SHIFTER SHAFT COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
Models This kit fits 1982 and later Touring and FL Softail model motorcycles. Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not Sold Separately Gear shifter shaft cover Not Sold Separately Screw, set There are no Service Parts available with this kit. INSTALLATION 1. Remove the stock heel shift lever from the gear shifter shaft. 2. Install the set screw into the gear shifter shaft cover. 3. Install gear shifter shaft cover with installed set screw over the end of the gear shifter shaft. 4. Tighten the set screw until light contact is made with the shaft groove. 5. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw.

HARLEY DAVIDSON VRSC ACCESSORY BACKREST PADS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
INSTALLATION NOTE It is easiest to mount these backrest pads with the sissy bar upright kit already installed. 1. Install the sissy bar upright according to the instructions included with that kit. 2. Hold backrest pad against upright with pad facing forward. 3. See Figure 1. Align two pad mounting holes in sissy bar upright with two threaded inserts in backrest pad. 3 1 2 is00007 1. Backrest pad mounting holes 2. Screw (4) 3. Sissy bar Figure 1. Sissy Bar and Screws 4. See Figure 2. Begin threading each of the two button head cap screws. Threading these screws may be a little difficult at first since the screw must break through plastic sheeting inside the backrest pad to reach the threaded insert. It may be necessary to use a 4 mm hex wrench, while holding the backrest pad tight against the upright to get the screws started. 5. Using a 4 mm hex wrench (allen wrench), tighten each screw a little at a time, alternating side-to-side. This is done to ensure the vinyl stretches evenly in the recessed channel that the upright bar is drawn into. Continue alternating side-to-side until both screws are secure. 6. Tighten both screws to 50-60 in-lbs (5.6-6.8 Nm)

HARLEY DAVIDSON FLHTCUSE TOUR-PAK INSTALLATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
INSTALLATION Prepare Motorcycle for Service 1. See the Owner’s Manual and remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Remove the bolt and negative (-) battery cable from the battery. 7 6 5 4 3 1 2 is01951 1. Loading coil assembly 2. Nut 3. Lock shroud 4. Clip, locking (Sold Separately) 5. Nut 6. Screw 7. Tour-Pak lockset Figure 1. Antenna Loading Coil and Tour-Pak Lock Installation 3. Remove the bolt and positive (+) battery cable from the battery. 4. Install a Tour-Pak Rack kit (53276-04, 53118-98A or 53260-02) according to the Instruction Sheet contained in the kit. 5. For FLHX and FLTR models: Install Antenna Relocation kit according to the instruction sheet in that kit. NOTE Discard antenna mounts from antenna relocation kit and use mounts supplied with this kit. To open the Tour-Pak prior to installing the Tour-Pak lock, insert a flat head screwdriver into the lock location and turn clockwise while pulling up on the lid. 6. Install the Tour-Pak onto the Tour-Pak Rack using the hardware included in the Tour-Pak Rack kit according to Instruction Sheet included with that kit. Install Tour-Pak Components

HARLEY DAVIDSON COMFORT PROFILE REAR SADDLEBAG GUARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2011

download
REMOVAL 1. Remove saddlebags from motorcycle following the instructions in the service manual. 2. See Figure 3. Remove grab strap screw and washer (G). Remove grab strap (H). Remove seat following the instructions in the service manual. 3. Remove left and right side covers (located in front of saddlebags) by removing screw from bottom of side cover. Save hardware and side covers for final assembly. 4. Support muffler assembly with a block of wood or other suitable method. For FLTR and FLHX Models 1. See Figure 3. Remove the screws (F) securing saddlebag guards to muffler supports. 2. Remove bolt (M) and nut (P). Save bolt (M) for installation. Discard nut (P). 3. Remove screws (B and C) and nut (E). Save screws (B and C) for installation. Discard nut (E). 4. Remove stud receptacle (I) and save for installation. 5. See Figure 1. Remove antenna bracket (1), mounting fasteners (2), antenna mounting nut (5), washer (4) and antenna adapter (3). Save the antenna and hardware, discard the bracket. 6. Remove support (D) and discard. 7. Repeat Steps 1 through 4 for other side. For FLHTCU and FLHTC Models 1. Remove and discard screws (X) and guard rail mounts (W and V). 2. Remove screw (Q) and rear guards (U). Discard rear guard assembly including screws (T) and clamps (R and S). Discard screw (Q). 3. Remove and discard screw (K) and nut (L). 4. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E), screw (N) and forward guard. 5. Repeat Steps 1 through 5 for other side. For All Other Models 1. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E) and screw (N). 2. Remove and discard screw (K) and nut (L). 3. Remove forward guard and discard. 4. Repeat for other side