2002 Kawasaki 360 ATV WINCH ACCESSORY INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 08-05-2012

download
1. Remove the two 8mm bolts that attach the front bumper assembly to the ATV frame see figure 3. 2. Place Winch mounting plate (A1) into position and fasten the two bent down tabs to the ATV frame using the two 8mm bolts removed in step one, see figure 4, and figure 5. Do not tighten fully at this time. 3. Attach the front of the mounting plate using four 1/4-20 u- bolts (B1), eight lock washers (B2), and eight 1/4-20 hex nuts (B3), see figure 6. 4. Tighten all fastners for the mounting kit at this time. 5. Place winch into position behind the mounting plate. Attach the top two feet of the winch using two 5/16-18 hex cap screws and lock washer. These fasteners will be found in the hardware kit that came with the winch. Note: The winch has floating nuts in its feet. In some instances, a nut may be moved off to one side making it impossible to screw a bolt in. If this becomes the case, take a screwdriver and center the floating nut in the winch to the bolt hole opening. Now attach the bolt through the Winch Plate and into the winch. 6. If using a Cast Hawse Fairlead: It may be neccasary to remove the cast hawse fairlead from the fairlead mounting plate that came with the winch.

YAMAHA PRO-R AIR CLEANER REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 07-01-2012

download
STEP 1 Remove the seat, fuel tank, and OEM air cleaner assembly. Disconnect the hoses connected to the air cleaner while leaving them connected to the motorcycle. Save the clamp that secures the air duct to the carburetor and the OEM fasteners used to secure the stock air cleaner assembly to the motorcycle as some will be reused. STEP 2 Remove the carburetor according to the section in your Road Star factory service manual that outlines procedures for carburetor removal, disassembly, reassembly and installation. Now is a good time to proceed with re-jetting the carburetor. We have supplied jets to cover many common configurations. For jet locations and jetting recommendations with various exhaust combinations see Addendum I. Since the OEM screws retaining the float bowl are easily damaged, we have included replacement M4 socket head cap screws to replace them, if necessary. STEP 3 Insert the rubber intake duct into the main support bracket as shown in PIC. 1. The rubber nipple should be pointing toward the longest leg of the bracket. STEP 4 Insert the rubber intake duct into the Pro R-series Hypercharger in the same fashion it was installed in the main support bracket. See PIC.2. You may need to use a screwdriver to help “poke” the flange of the Rubber Intake Boot into position inside the Pro R-series Hypercharger. STEP 5 Line up the three holes in the back plate of the Pro R-series Hypercharger and the three holes in the flange of the rubber intake duct with the three holes in the main support bracket. Insert the three supplied 1/4″-20 x 5/8″ socket head cap screws from inside the Pro R-series Hypercharger and secure on the back side of the main support bracket with the 1/4″-20 thin nylock nuts. You will need to pull back the inner flange of the rubber intake duct to access the holes. Hold the nylock nuts with a 7/16″ wrench as you tighten the socket head cap screws with a 3/16″ hex key. Be careful not to over tighten and cause the rubber intake duct to pucker around the nylock nuts. See PIC.3.

Incoming search terms:

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

HARLEY DAVIDSON STEALTH OPERATOR FOOTBOARD INSERT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
This kit fits all 2004 and later FLHRS/I (Road King®Custom) model motorcycles. This kitalso fits 1986 and later FLHR/I/CI, FLHT/C/CI/CUI and FLTR/I models equipped with footboard pans 50683-04 (right) and 50688-04 (left) . This kit contains the following items: QTY DESCRIPTION PART NO. 1 Footboard insert (right) 51057-04 1 Footboard insert (left) 51055-04 Installation 1. Apply liquid dishwashing soap to the footboard-insert rubber beads protruding through the bottom of the foot- board. 2. With the operator footboard in the “up” position, use a screwdriver to work the rubber footboard beads out through the top of the footboard. 3. Apply liquid dishwashing soap to the rubber beads on the new footboard insert. 4. Place the footboard insert into position on the footboard. Use a pliers to pull each rubber bead into its footboard hole until the beads protrude through the footboard. 5. Repeat the above steps for the remaining footboard insert.

Fitting Hondaline Heated Grips to Honda GL1800

0

Filed Under (Honda) by admin on 08-04-2011

download
Then remove the right side fairing trim piece, starting at the bottom inner and working your way upwards. Unscrew the single Allen head bolt holding the lock panel in place and remove the panel. Now to remove the old grips. Tip; If you have chrome cap ends fitted, protect the chrome on the screw by putting some tape on the end of the screwdriver If you’re a cheapskate, and want to save the old grips, run a thin screwdriver or a hacksaw blade around the inside of the grip to loosen the old glue and it will come away easily. Repeat on the right side grip. The Honda instructions tell you to remove the whole throttle grip & boss but you don’t need to go to all that hassle of unscrewing the switch assembly to get at it. Just remove the rubber grip same as described for the left side After removing the switch panel from the Goldwing, drill a 45mm hole with a holesaw. The spot to drill is marked on the inside of the panel. Then just screw the controller knob assembly into position with the three screws provided (second picture) Spread some glue (the Honda stuff if you can get it, or just plain old rubber cement as I’ve used on my last four Goldwings without problems). Spread it more towards the ends and middle of the bar as it will get pushed inward as you push the grips on anyway

Incoming search terms:

HARLEY DAVIDSON NOSTALGIC RIDER FOOTBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 22-03-2011

download
This kit is designed for use on 1980 and later FLT, FLHT, FLHR, FLHS model motorcycles and 1986 and later FLSTC, FLSTN, FLSTF and FLSTS model motorcycles Installation Removal of previously installed footboard cover: 1. With left side operator footboard in up position, use a screwdriver to work rubber footboard cover collars out through the top of the footboard. To install operator chrome footboard covers: 1. Moisten kit footboard cover rubber collars with dishwashing soap to ease installation. 2. With footboard in up position, firmly hold new footboard cover in installation position. From underside of footboard use a pliers to pull each rubber isolator into its footboard base hole until the thick collar emerges. 3. Repeat procedures for right side footboard cover. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON HERITAGE CHROME FRONT FENDER RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION NOTE See Figure 1. Be careful not to crack plastic fender lamp lens (2) or chrome plate when removing lens. 1. Remove fender lamp light lens (2) by placing screwdriver in slot in top of lens and carefully prying cover loose. Retain lens and gasket for later installation. 2. Loosen four hex socket head screws (1) which attach fender (4) to fender mount. 3 2 4 1 is03805 1. Fender mount screws (4) 2. Fender lamp light lens 3. Fender Rail 4. Fender Figure 1. Installed Front fender Rail NOTE When installing fender rail (3), be sure fender rail supports are inside of fender. 3. Place fender rail (3) from kit into position, aligning the front bracket hole of rail with hole in front of fender (4). Fender rail supports will fit snugly inside fender. NOTE Be careful not to damage the fender lamp wire when securing front fender rail into place. 4. Use a magnet to place a 10-32 x 1/2 inch phillips screw through the hole in front fender and through front bracket hole of fender rail (3). 5. Loosely secure fender rail (3) to fender (4) with 1/2 inch flat washer and hex locknut. 6. On right side only, remove two hex socket head screws and nuts. Retain nuts for installation. 7. Replace original two socket head screws with 5/16-18 x 2 inch screws from kit. 8. For vehicles without caliper/rotor covers: On left side of fender (4) only, install a washer between rail (3) and fender for both screws. Replace original two hex socket head screws with 5/16-18 x 2 inch screws from kit. For vehicle with caliper/rotor covers: Do not replace hex socket head screw that supports caliper/rotor cover. On left side of fender (4), install a washer between fender (4) and rail (3) on screw that does not support the caliper/rotor cover (towards the front of the vehicle). Replace remaining hex socket head screw with 5/16-18 x 2 inch screw from kit. 9. Install four original nuts. 10. Tighten front bracket Phillips screw securely. Tighten four hex socket head screws to 14-18 ft-lbs (19-24 Nm). 11. Install gasket and fender lamp lens removed earlier

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME REAR TURN SIGNAL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. Remove the Existing Rear Turn Signals 1. For 2006 and Earlier Models: See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 3. Identify the white left [19] (1) and black right [18] (2) 2 pin rear turn signal connectors. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To remove the rear turn signal wires from the socket terminal housing, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 7. Repeat for the opposite turn signal. 1. For 2007 and Later Models: See Figure 2. Open seat and remove the nut and washer (3), seat post (2), passenger pillion and passenger seat (1) per the instructions in the Service Manual. 2. See Figure 4. Identify the left (1) and right (2) rear turn signal wires and 6 pin rear turn signal connector [94]. 3. See Figure 6. To separate the rear turn signal connector, press the button (1) and separate the pin terminal housing from the socket terminal housing. 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. See Figure 5. Remove the turn signal wires from the 6 pin socket terminal housing. To remove the wires, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. Repeat for all four turn signal wires. Do not remove the license light wires from the socket terminal housing. 6. Gently pull the loose turn signal wires through the sheath toward the rear of the vehicle until completely removed from the sheath. 7. See Figure 7. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket and remove turn signals. 8. Repeat for the opposite turn signal

Incoming search terms:

HARLEY DAVIDSON DASH PANEL EXTENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION 1. Remove the seat. 2. See Figure 1. Loosen the two socket head screws on the instrument panel console. Raise the console enough to access the two pushnuts holding the upper end of the leather insert. Remove and discard the pushnuts using pliers or a blade-type screwdriver. 3. Remove and discard the phillips head screw (3) and washer (4) securing the lower portion of the leather insert to the fuel tank. Remove the leather insert and discard it. 4. Obtain the dash panel extension (1) and the dash panel extension trim (2) from kit. Place the dash panel extension on the dash panel extension trim making sure the panel is centered and fits cleanly into the lips on both sides of the trim. 5. Gently lift up on the rear of the instrument panel console and install the dash panel extension with the rubber dash panel extension trim underneath, butting the two together. Make sure the rubber dash panel extension trim is aligned with the dash panel extension. Finger tighten the two socket head screws to hold down the instrument panel temporarily in place. NOTE The console rubber trim from a stock vehicle may need to be trimmed slightly to assure proper fit. NOTE When performing the next step, note that proper alignment is achieved when space is eliminated between the instrument panel console and/or between the dash panel extension trim piece and the fuel tank. Due to variances in fuel tank and instrument panel console fitments, the foam pads are used on “as needed” basis to achieve proper alignment. It may be necessary to experiment a few times using various combinations of pads to achieve the desired alignment. In some cases, pads may not be necessary while in others, it may be necessary to use all with one stacked above another. 6. Observe the overall fitment of the panels over the tank and determine whether the foam pads will be necessary to achieve the desired alignment. 7. If necessary, remove the dash panel extension assembly. Peel the adhesive backing and install the needed foam pads (5) to the raised areas extending from the front of the dash panel extension as shown. Re-install the panel. 8. When the proper alignment between the new kit and the fuel tank is achieved, tighten the rear mounting screw (3) with the washer (4) to the speed nut located on the tab at the rear of the fuel tank. 9. Tighten to 18-24 in-lbs (2.0-2.7 Nm). 10. Tighten the instrument panel console?s two socket head screws to 18-24 in-lbs (2.0-2.7 Nm). 11. Install the seat

Incoming search terms:

HARLEY DAVIDSON SMOKED AND CLEAR FENDER TIP LENS KITS Preparation MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery cables, negative cable first. 2 . See Figure 1. Insert blade of small screwdriver into slot at top of front fender tip lamp lens (2). Rotate end of screwdriver to unsnap lens from lamp bracket. Repeat for rear fender tip lamp lens. 3. Remove bulb (3) from socket (4). 4. From the kit, find the LED marked “Amber” (5) and install into front fender tip lamp assembly.lamp socket. 5. From the kit, find the LED marked “Red” (5) and install into rear fender tip lamp assembly.lamp socket. Always connect the positive battery cable first. If the positive cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 6. Connect the battery cables, positive cable first. 7. Apply power and check for proper function of front and rear fender tip lamps