Kawasaki Sxi/ SXR Ignition twin cylinder Jet Ski ignition Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove electronics enclosure from its mounting location. 2. Unplug and remove the OEM ignition. 3. Set the programming switches on the T3 to your settings. 4. Install the T3 Ignition in the same location in the electronics enclosure. 5. Test the T3 Ignition. 6. Close the electronics enclosure cover plate and mount the module in the PWC. Installation Remove electronics enclosure from its Mounting Location 1. Using a 10mm socket remove the mounting bolts on each side of the electronics enclosure. 2. Remove the enclosure cover and set aside the screws, 2 mounting flanges, ‘O” ring, and enclosure top. Unplug and Remove the OEM Ignition 1. Using 10mm socket, remove bolts from each side of the OEM ignition. Lift out the ignition and unplug all connectors attached to the OEM ignition. Now remove the protective metal plate that was under the ignition and two 3/16″ thick washers under that plate. 2. On 2004 models and newer remove the wire harness for the two black connectors just unplugged from the OEM ignition. Trace each wire from each black connector back to in-line connectors and separate each of these connectors. Set the two harnesses aside. Install the T3 Ignition in the Electronics Enclosure 1. Install the T3 ignition into the mounting bracket supplied with your T3. Slide the end of the ignition module under the lip at the rear of the bracket an press the wire end of the ignition firmly into the bracket. Attach the keeper bracket using two 5mm bolts supplied. Place the ignition/bracket in the location where the OEM ignition and metal plate were removed. Secure the ignition in place with the supplied bolts

Incoming search terms:

Kawasaki Teryx Dash Frame Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The BRP Dash Frame mounts in place of the factory cup holder/storage pocket. Remove the screws holding the cup holder or storage pocket from the back of the dash and remove it. Hold the Dash Frame up on your dash. The top of the frame includes a channel that your dash slips into to provide support. Press the frame firmly up and against the dash. Be sure the frame is centered and straight. Using the frame as your template drill out the two top holes using a 13/64″ drill. Each hole is located at the top corner of the frame. Alternatively, you can mark the location of the holes, then drill them out with the frame removed. Using the smaller button head bolts supplied with this kit, along with the nylock nut and rubber backed washer, mount each of the two top corners of the frame. Use caution when tightening however. The angle of the dash frame is different than the angle of your plastic dash. The two bolts are only needed to snug the frame against your dash. You should only snug the bolt up, but don’t tighten it down. Looking from the back of the dash, you’ll see that the rubber washer does not lay flat against the plastic of the dash. This is correct. Again, these bolts are only to snug the frame against your dash and should not be tightened down. Doing so could damage your dash. The supplied nuts are nylock and will not back off even though the bolt is not tightened.

Incoming search terms:

Kawasaki KFX 700 INSTALLATION and REMOVAL INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Jetting (see Picture on next page) 1. Remove vacuum slides from carbs. Remove stock needles & spacers, note order of assembly. 2. Install LTE needles on groove # 4 counting from the top down. 3. Remove stock main jets and replace with the supplied main jets. 4. Locate the fuel mixture screws. Using a flat blade screwdriver, turn the mixture screws clockwise until seated, then turn out 2.5 turns.
FINISHING UP Be sure all wires and hoses are zip-tied back so they will not touch the exhaust. QUIET CORES Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. FIRST RIDE Your first ride after installing exhaust should be no longer than 20 to 30 minutes. Let your ATV cool and re torque all of the hardware on your new exhaust. Silencer Packing

Incoming search terms:

Incoming search terms: