KTM Rear Wheel Bearing Installation and REMOVAL

0

Filed Under (KTM) by admin on 23-01-2012

download
1 Insert a long punch (with a good square edge) into the center of the aluminum wheel bearing spacers and push up against the inner edge of the spacer on the opposite side of the wheel (Fig. 1). 2 Using a hammer, tap the punch around the entire circumference of the spacer until it completely slides out of the bearing (Fig. 2). Turn the wheel over and remove the other spacer in the same way. 3 Use a long screwdriver or narrow pry bar and pry the seals out of each side of the wheel (Fig. 3). 4 Using snap ring pliers, remove the bearing retaining snap ring from either the disc or sprocket side of the wheel (Fig. 4). 5 Insert a long punch (with a good square edge) into the center of the wheel bearing, and push up against the inner edge of the bearing on the opposite side of the wheel. Using a hammer, tap the punch around the entire circumference of the bearing until it completely slides out of the hub. Turn the wheel over and remove the other bearing in the same way. NOTE: It may be necessary to tap on the punch sideways at first to knock the center aluminum sleeve off center so that you are able to get the punch on the edge of the bearing. 6 Clean areas where bearings will be inserted back into hub and apply a thin coat of grease around the machined hub surface. Tap the bearing on the snap ring side of the hub into the machined hub surface, making sure to keep it square with the hub as it goes in and only tap on the outer race of the bearing. Once you get the bearing flush with the outer edge of the hub, use a socket or piece of pipe that is just smaller than the outside diameter of the bearing to finish tapping the bearing into the hub. (Fig. 5)

YAMAHA WR450F (S) 2-TRAC SPECIFICATIONS/ SUPPLEMENTARY OWNER’S SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
CABLE ROUTING DIAGRAM STEERING DAMPER ADJUSTMENT 19 Damping sweep controls Damping sweep ontrols 5 are located on each side off the damper body. Damping is in position 2, (12 o´clock), when delivered from Yamaha. This setting is fitted for enduro, motocross and off-road riding. WARNING Always ensure that valve setting is within the permitted ranges. NOTE: Both damping sweep controls must always be set in identical positions. Always use positions according to the clock. Suitable starting position: Motocross pos. 1 or 2 Enduro pos. 2 or 3 Off-Road pos. 2, 3 or 4 Technical data External measures 70x70x35 mm Seals Low friction type Oil Öhlins part no. 01306-01 Maintenance and inspection The steering damper is a precision instrument, with extremely fine tolerances. It is therefore essential that it is maintained in a correct manner. Maintenance and service should be carried out by an authorised service center. NOTE: After washing the motorcycle wipe clean and spray with all-round oil. Never subject to direct high-pressure cleaning since water may otherwise penetrate the damper. Ensure that there is no leakage of fluid and that there is no visible damage to the housing and mounts FRONT FORK REBOUND DAMPING FORCE ADJUSTMENT The rebound adjuster is located at the top of the fork leg. 1. Adjust: • Rebound damping force By turning the adjuster. Stiffer → Increase the rebound damping force. (Turn the adjuster in.) Softer → Decrease the rebound damping force. (Turn the adjuster out.) Extent of adjustment: Maximum Minimum Fully turned in 20 clicks out position (from maximum position) • STANDARD POSITION This is the position which is back by the specific number of clicks from the fully turned-in position. Standard position: 14 clicks out Do not force the adjuster past the minimum  or maximum extent of adjustment. The adjuster may be damaged. WARNING Always adjust each front fork to the same set- ting. Uneven adjustment can cause poor handling and loss of stability

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM TAPPET ROLLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

Incoming search terms:

All Harley Davidson Oil Recommendations

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
Harley Davidson has manufactured 9 types of engines from 1929 to the current model. Flathead (1929-1974), Knucklehead (1936-1947), Panhead (1948-1965), Shovelhead (1966-1984), Evolution (Blockhead) 1340 (1984-1999), Big Twins 1450 (2000 to current), Revolution/V-Rod (2001 to current) Ironhead Sport- sters (1957-1984) & Evolution Sportsters 1985 to current. Harley Davidson recommends SAE 50 or 60 for the engine oil in their Flathead, Knucklehead, Panhead, and Shovelhead. AMSOIL recommends AHR SAE 60 or MCV 20W-50 motorcycle oil for all these older models. Use AMSOIL SVG or SVO for the transmissions. Of these models only the Shovelhead has a chain case that is lubed, and is fed by the engine oil. In the Evolution 1340, Big Twins 1450, and V-Rods, AM- SOIL recommends MCV 20W-50 motorcycle oil in all 3 holes (engine, transmission, and primary chain case). AMSOIL recommends SVG as an alternative oil for the transmission, and SVO as an option for older transmissions. New seals are recommended where excessive leaking exists.