Harley-Davidson Standard Seat Installation Instructions

0

Filed Under (Harley Davidson) by admin on 24-04-2012

download
Step 1 – Remove the original seat and place it bottom side up next to your new custom replacement seat. Step 2 – Remove each bracket from your original seat and install it in the corresponding location on your new seat, using the 1/4-20 bolts provided. Place the new bolts through the brackets and into the threaded jacknuts in the new seat bottom. Repeat until all hardware is transferred. Step 3 – Check all fasteners for tightness, 10-15 ft/lbs is recommended, do not over-tighten. Step 4 – Remove rubber bumpers from your original seat and move them to your new custom seat. In some instances we have already installed bumpers that are needed, but some models require the special specific bumpers from your original seat for proper tolerance and fit. The stock bumpers are easily removed by twisting and pulling at the same time. Reinstallation requires drilling a hole of the same diameter as the original into the new seat pan. Rubber bumpers are most easily installed using either water or silicone spray as a lubricant.
Step 5 – Reinstall the seat on the motorcycle. Check to make sure the seat fits properly. The new seat will be more firm than the original seat and will break-in over time to provide greater comfort. During the break-in, the seat will also settle-in, or lower, about ½ to one inch. Older seats may seem substantially lower because of the worn-out, compressed foam that has deteriorated with time on your original seat

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms: