HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

DUCATI ST2/ ST4 Stock Socket Rewire Installation Instructions

0

Filed Under (Ducati) by admin on 25-10-2010

download
STEP #1 Remove necessary fairings. STEP #2 Unplug the stock connector; plug in the new harness. STEP #3 Route wires starting at the bracket end and finishing at the battery. STEP #4 Look over your work. STEP #5 Check the polarity & test. STEP #6 Put everything you took off back on. Detailed Instruction: STEP #1 – Remove the seat, front, right side, & left side tail fairings. See the Ducati service manual. STEP #2 -Locate the white connector on the back of the stock socket. Unplug this connector and ty-wrap it into a safe location. Plug the new wiring harness into the back of the stock socket. The center terminal is plus and the outer ring is negative (see dwg below). Apply either dielectric grease or Vaseline to the terminals. STEP #3 – The harness is designed so the wires leave the connector toward the back of the bike, (this way they will not be seen). Loop the wires up through the gap between the frame & the engine controller (or storage bin). On the left side there is a small gap; do not pinch the wiring. You will need to remove four screws on the engine controller to accomplish this. Next cross over behind the engine controller (or storage bin). Re-tighten the engine controller. The harness is now routed toward the front of the bike [A]. Loosen right tail fairing front clip screw & pass the wiring harness under it [B]. Route the harness between the frame and the engine going towards air box. Using a ty-wrap attach the fuse holder to the back, right, air-box post [C}. In this location the fuse can be easily accessed under the tank. The ground wire is attached to a gas tank hinge bolt [D]. Connect the two wires as follows: RED WIRE = BATTERY POSITIVE BLACK WIRE = GAS TANK HINGE BOLT STEP #4 – Apply the remaining ty-wraps in useful locations. Do NOT allow the harness to directly contact the motor or exhaust