HARLEY DAVIDSON DYNA PASSENGER PILLION SEAT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVE SEAT NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove screw to detach rear seat mounting bracket from fender. 2. Remove two capscrews that attach seat mounting bracket to bottom of stock seat. 3. Remove the existing seat from the motorcycle. Save the seat bracket and mounting screws for installation of the new seat. 4. If motorcycle has a grabstrap installed, remove nut and washer that holds passenger strap in place and remove strap. 5. See Figure 1. Remove the plastic cap from rearmost fender hole (3). 6. Remove the seat retention nut and washer from the solo seat mounting hole. 7. See Figure 2. A cable strap may be used as an installation aid to remove and reinstall the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the rearmost fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. 8. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap. 2 5 1 2 1 3 6 7 4 is00363 1. Retention nut and washer (2-up seat positon) 2. Retention nut and washer (solo seat position) 3. Rear-most fender hole 4. Middle fender hole 5. Grabstrap mounting hole 6. Flange screw 7. Plastic retention nut

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DIAMOND BACK SEAT installation instructions

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation NOTE When this seat and tail section are installed, the passenger foot pegs or foot boards and the passenger grab strap must be removed. NOTE: A Service Manual for your model motorcycle is available at your Harley-Davidson Dealer. 1. Refer to applicable Service Manual and remove original seat, foot pegs or foot boards and grab strap. 2. Refer to Tail Section Instruction Sheet for instructions describing how to attach the tail section to the seat and installing the seat on the motorcycle

HARLEY DAVIDSON DYNA SEAT WITH ADJUSTABLE RIDER BACKREST INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION Seat Installation NOTE When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. 1. Remove the existing seat and passenger grab strap following the instructions in the appropriate Service Manual. Discard the grab strap and retain all other hardware for later use. 2. See Figure 9. Remove the seat bracket from the stock seat. 3. For all except FXDWG: Install the stock seat bracket onto the new seat with the stock screws. For FXDWG: Install new seat bracket 52152-97 onto the new seat with the stock screws. For models equipped with original or accessory two- up seating: Proceed to Step 6. 4. On models equipped with an accessory Solo Seat: Remove the plastic plug from the hole in the rear fender where the rear seat bracket will be attached. 5. See Figure 9. Slide the retention nut (9) onto the cable strap (11) so the wide end of the nut rests on the eye of the strap. Thread the cable strap up under the fender and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. Seat the rib of the retention nut in the notch in the fender hole and slide the retention washer (10) into place from the rear. This will lock the retention nut in place. 6. See Figure 1. Place the black bracket (1) from the kit onto the frame as shown. 7. See Figure 9. Install the new grab strap (8) in the original location with the hardware saved in Step 1. Tighten the nut to 96 in-lbs (10.85 Nm) . 8. See Figure 1. Install the screw (2) in the hole on the forward edge of the bracket. Attach the locknut (3) and washer (4) from under the frame. Tighten to 96 in-lbs (10.85 Nm)

HARLEY DAVIDSON BADLANDER XL CUSTOM SEAT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
Removal of Stock Seat 1. Remove screw (8) to detach rear seat mounting bracket from fender. 2. Slide seat rearward to unhook front of seat from frame, then remove seat. 3. If equipped with a grab strap, remove hardware that holds it in place and remove strap. Installation of Kit Seat For 1996 and earlier models: Make certain you select the correct kit screw in step 1. Attempting to install a coarse threaded screw in a fine threaded hole, or vice versa, will damage threads. 1. Secure grab strap (2) to fender using washer (7) and appropriate screw (6) below: On 1995 and earlier models use 1/4-28 (fine) screw. On 1996 – 2003 models use 1/4-20 (coarse) screw. 2. Slide seat into position until front of seat engages frame, then secure bracket to fender with screw (8) using guide washer (3) between bracket and fender with the small washer diameter facing upwards. The guide washer will center the screw in the bracket hole and serve as a washer to protect the fender. NOTE For 1997 883 models, a retention nut and washer must be installed into the fender hole, covered with a plastic cap, where the rear seat bracket will be attached. A cable strap is included to aid in this installation. For 1997 – 2003 models: 1. Install grab strap (see step 1 for 1996 and earlier models). 2. Remove plastic cap from hole in fender where the rear seat bracket will be attached. 3. Place retention nut (5) over cable strap (9) so wide end of nut rests on eye of cable strap. Thread cable strap up under fender and through fender hole. Pull up on cable strap to hold nut snug against underside of fender. 4. With rib on retention nut seated into notch in fender hole, slide retention washer (4) into place from the rear. This will lock the retention nut in place. 5. Slide seat into position untilang=en

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms: