HARLEY DAVIDSON XL 2-UP CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Additional Parts Required •XL883 and XL883L models require the separate purchase of Passenger Footpeg Kit 50203-04, which is available from a Harley-Davidson dealer. •XL1200N, XL883N and XL1200X models require separate purchase of guide washer 7487. Kit Contents See Table 1 and Table 2 for the kit number and corresponding grabstrap number. See Figure 7 and Table 3 for a list of the service parts. Table 1. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52883-04A 51295-04 51686-05 51312-07 52907-04A 51295-04 52283-06 51312-07 52923-04B 51295-04 52299-06 51312-07 52859-04B Table 2. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52849-04B 51295-04 51386-04 51312-07 52871-04A 51295-04 51684-05 51312-07 52884-04A 51295-04 51685-05 51312-07 52916-04B 51295-04 52176-06 51295-04 52184-06 INSTALLATION NOTE When installing this kit, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. Models Originally Equipped With Solo Seat 1. Remove the seat according to the instructions in the owner’s manual. 2. See Figure 1. Remove and discard seat post washer (2) and screw (3) from the front fender hole. 3. For XL883 and XL883L models: See Figure 2. Remove plastic cap (1) from rearward fender hole and save. 4. Remove retention nut (2) and washer (3) from middle fender hole

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

Incoming search terms:

HARLEY DAVIDSON VRSC ACCESSORY SEATS AND PILLIONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Installing Seat and Pillion Kits: 51584-01, 52028-02, 52036-01, 53432-02, or 52927-05 NOTE Proper installation of 53432-02 (Sundowner) and 52927-05 (Tallboy) requires installation of Fender Base Plate Kit 51120- 01 1. Refer to the appropriate Service Manual and remove the stock seat and pillion. 2. See Figure 2. Remove the two mounting bolts (2) from the passenger grabstrap (1). Save the bolts for re-installa- tion. NOTE The grabstrap must loop toward the rear. Check that the “Harley-Davidson” text on the grabstrap can be read from the front of the vehicle. 3. See Figure 2. Install stock grabstrap bolt, and one end of grabstrap as shown. While holding the grabstrap end parallel to the formed line of the fender, tighten the bolt to 8-12 Nm (71-106 in-lb ) . Repeat for opposite end of grabstrap. NOTES The new pillions included in Kits 52028-02 (Custom), 52036- 02 (Badlander) and 51584-01 (Leather Badlander) are installed from front-to-back. The pillion included in Kits 53432-02 (Sundowner) and 52927- 05 (Tallboy) must be installed through the grabstrap from back- to-front. To install the Sundowner or Tallboy Pillion on a motorcycle having a sissybar upright installed on Fender Base Plate Kit 51120-01, remove the upright before installing the pillion. Reinstall the upright after the Sundowner Pillion is installed. For kit numbers 52028-02 (Custom), 52036-01 (Vinyl Bad- lander) and 51584-01 (Leather Badlander) Seat Kits, be aware of the following: The 2003 Model Year 100th Anniversary VRSCA vehicle with two-tone sterling silver and vivid black paint has protective tape covering the rear under-the-seat area of the airbox cover. For the seats listed above, it will be necessary for cosmetic reasons, to carefully remove the protective tape and reapply it so it is in the correct position for these shorter-nose seats. Some trimming of the lower portion of the protective tape may be necessary to eliminate interference with the airbox cover latch. If necessary, reorder protective tape (48403-03). 4. Install new pillion into position through grabstrap. Prevent pinching TSSM control wiring by routing the cable through the channel on the underside of the pillion (see Figure 2) and away from the pillion mounting bolt. Pinched wiring may damage the TSSM system. 1 3 2 is00014 1. Pillion 2. Grabstrap 3. Pillion base mounting hole Figure 3. Pillion Base Mounting Hole 5. See Figure 3. Push the pillion (1) forward through the grabstrap (2) until the pillion mounting hole is approximately 25 mm (1 in.) forward of the hole (3) in the frame. 6. See Figure 2. Push down on the pillion and slide the pillion toward the rear to engage the pillion slot with the fender tongue (5). Push rearward until the pillion mounting holes align. After installing pillion, pull upward to be sure it is locked in position. While riding, a loose pillion can shift causing loss of control, which could result in death or serious injury. (00387a) 7. Install original pillion mounting bolt. Tighten bolt to 11-14 Nm (97-124 in-lb ) . 8. Re-install the sissybar upright, if removed earlier. 9. Position the seat (as if opened) onto the frame. Slide the seat forward to insert the seat-hinge pins into the bushings on the frame. 10. See Figure 1. Clip the plastic seat-hinge sleeve (2) over the seat hinge. 11. See Figure 1. Insert the seat tether (3) into the hole in the motorcycle frame. 12. Refer to the applicable Owner’s Manual and close the seat. Installing Seat Kits: 51595-05, 52024-01, or 51647-06 Kit 51595-05 requires the use of pillion kit 51594-05. Kit 51647-06 requires the use of pillion kit 51648-06. Kit 52024-01 requires the use of either the stock pillion or Touring Pillion 52023-01A. 1. Refer to the appropriate Service Manual and remove the stock seat.

Incoming search terms:

HARLEY DAVIDSON XL SOLO CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. 1 2 4 1 3 is03341 1. Stock retention nut and washer 2. Plastic cap 3. Rearward fender hole 4. Center fender hole Figure 1. Retention Nut and Plastic Cap Location 2. For models that had a solo seat: Proceed to Step 3. For models that had a 2-up seat: The retention nut and washer must be moved from the rearward mounting hole to the center fender hole where the rear seat bracket will be attached. Use a cable strap to aid in this step as fol- lows: a. See Figure 1. Remove retention nut from rearward fender hole (3) and plastic cap (2) from center fender hole (4). b. Install plastic cap into the rearward fender hole. c. See Figure 2. Place the retention nut over the cable strap so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the center fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib of the retention nut seated into the notch in the fender hole, slide the retention washer into place from the rear. This will lock the retention nut in place. 3. Position the solo seat on the motorcycle frame with the mounting bracket at the rear. Bring the seat forward and engage the tab on the seat into the slot at the base of the fuel tank. 4. See Figure 3. Secure the seat to the fender using the knurled knob (3) and neoprene washer (4) from the kit. Install the washer on the knob and tighten the knob securely to the fender seat nut

HARLEY DAVIDSON SOFTAIL SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION FXST, FXSTS, and FXSTB models NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove existing seat from motorcycle by unscrewing seat at rear bracket and unhooking front seat tab. 2. See Figure 4. Remove and discard existing grabstrap and save fastening hardware from the motorcycle. 3. See Figure 4. Install the grabstrap (7) from kit with the hardware saved in Step 2. Install the grabstrap according to Figure 1. Kit Number: 51470-06A, 51397-06A Grabstrap Number: 51184-00 Kit Number: 51468-06A, 51469-06A, and 51801-07 Grabstrap Number: 51176-96B is00420 Figure 1. Grabstrap installment information 4. See Figure 4. Slide the back of the seat through grabstrap and hook front tab of seat (1) into frame. Secure seat bracket to fender with screw (8). After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 2007 and later FXSTC models NOTE Refer to the Owner’s, or Service Manual instructions for removal of the stock seat, and mounting hardware. 1. Remove, and discard the existing grabstrap, and mounting hardware. 2. Remove, and discard the plug in the rear mounting position on the fender. 3. See Figure 2. Using the retaining nut (1), washer (2), and cable strap from the kit; Install the nut, and washer in the rear hole location on the fender (Note: A cable strap can be used as an installation aid)

HARLEY DAVIDSON DYNA ACCESSORY SEAT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
For vehicles with 2-up seating 1. Remove the existing seat from motorcycle. Save the mounting screw for installation of the new seat. 2. Remove existing grab strap and all attaching hardware. 3. See Figure 1 for information on which holes to install grab strap through for your seat (use the hole shown dark in the illustration). Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). Tighten to 60-90 in-lbs (6.78-10.17 Nm) . 4. Position new seat on motorcycle. Be sure tongue on front of seat fully engages into the seat mounting slot between the gas tank bracket and frame. 5. Secure seat with stock screw. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Kit Number: 52284-06 and 52359-06 Kit Number: 52159-06 Kit Number: 51540-06 Kit Number: 52288-06 Kit Number: 51471-06 and 51472-06 Grab StrapNumber: 52370-04 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Grab StrapNumber: 51176-96B Grab StrapNumber: 51173-93 Kit Number52378-07 Grab StrapNumber: 52313-96 is03552a Figure 1. Grab Strap installment information For vehicles with solo seat 1. Remove the existing seat from the motorcycle. Save the mounting screw for installation of the new seat. 2. See Figure 2. Remove the plastic cap from the rear most fender hole (3). 3. Remove the seat retention nut and washer from the solo seat mounting hole