HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN AND SMART SIREN II KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION 1. Refer to the owner’s manual and follow the instructions given to disarm the security system and remove the left- side cover. Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Refer to the owner’s manual and follow the instructions given to remove the main fuse. ALL models: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 3. Refer to the owner’s manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster┬«) models, the negative battery cable is most easily disconnected at the engine crankcase . 4. Remove the battery from the vehicle. 2 1 3 4 is 01377 1. Three-pin connector on siren harness 2. Three-pin connector [142B] on vehicle harness 3. Siren harness 4. Frame rear crossmember (not visible) Figure 1. Connect the Siren Harness to the Vehicle Harness 5. See Figure 1. Locate the siren connector (2) on the main harness, behind the harness shield forward of the battery location. It is covered by a dust cap. Pull the dust cap from the connector, and feed the connector downward and out from behind the shield. 6. Select the correct siren harness (3) for this model year vehicle from the kit. Route the three-pin connector (1) of the siren harness from the bottom of the motorcycle, between the primary cover and frame tube. Plug the connector into the siren harness connector (2) on the vehicle main harness. 7. Secure the connectors to the diagnostic harness using a cable strap from the kit. Route the long lead of the siren harness over the frame rear crossmember

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN AND SMART SIREN II BATTERY REPLACEMENT MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
SECURITY SYSTEM SMART SIREN AND SMART SIREN II BATTERY REPLACEMENT KIT SIREN BOX REMOVAL Read the following instructions and make sure you fully understand them prior to replacing the battery. If the procedure is not within your capabilities, or you do not have the correct tool, have a Harley-Davidson dealer replace the battery. Improper installation could result in damage to this product. (00419b) 1. Refer to the Owner’s Manual and follow the instructions given to disarm the security system. 2. Remove the siren box from the vehicle. Reference the siren installation procedures found in the Siren Kit Instruction Sheet or contact a Harley-Davidson dealer for specific information on locating and removing the siren box from your model. Battery replacement, Smart Siren 1. See Figure 1. Remove the battery cover (2) from the siren box as follows: a. Place the siren on a sturdy, flat surface with the potting (1) and battery cover facing up. b. Using a blunt, stiff blade such as a table knife, insert the blade between the case and cover at a 45 degree angle to the side of the case. Insert the blade until it touches the snaps on the inside face of the cover. Figure 2 shows the four barbed snaps (2). c. Twist the blade slowly so the inserted edge presses against the inside face of the cover. The cover will pop off and can be replaced later using silicone adhesive if necessary

Incoming search terms:

HARLEY DAVIDSON DYNA SECURITY SYSTEM SMART SIREN II KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
This kit fits 1996 through 2003 Dyna INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the Owner’s Manual and follow the instructions given to disarm the security system, remove the seat, and disconnect the battery cables (negative cable first). Retain all seat mounting hardware. 2 1 is 01366 1. Siren connector 2. Dust cap Figure 1. Siren Connector 2. See Figure 1. Locate the siren connector (1). It is covered by a black dust cap (2) and is at the end of an unconnected 10 inch (254 mm) long harness leg starting near the rear fender, close to the rear lighting connector. Free the siren connector from its constraints. 3. Remove the dust cap from the connector. 4. See Figure 2. Snap the siren (2) into the siren bracket (3) so that the sounder disc (4) fits the notch in the bracket as shown. Connect the siren connector (1) to the siren.

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
FL Touring models equipped with a TLE/ TLE Ultra Sidecar will require the additional installation of a Bank Angle Switch Kit (88115-03) and is available for separate purchase. See a Harley-Davidson dealer.INSTALLATION 1. Remove the original equipment (OE) Turn Signal Module (TSM) or Body Control Module (BCM) following the instructions in the service manual. 2. Install the Bank Angle Sensor (BAS) on sidecar vehicles. 3. Install the new turn signal/security module (TSSM) (7), Hands Free Security Module (HFSM) (1) or BCM (9, 11) from this kit, following the instructions in the service manual. Configure the Trike or sidecar TSSM, HFSM or BCM to “Side Car Enabled” using Digital Technician. 4. Install the Hands Free Security Module (HFSM) Antenna and antenna mount (6) if necessary, using the service manual instructions. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) ACTUATION 1. See a Harley-Davidson dealer to activate the key fob to the TSSM, HFSM or BCM. NOTE You can activate the TSSM fob by referring to the procedure in the electrical diagnostic manual. TRIKE AND SIDECAR CONFIGURATION (FL TOURING MODELS ONLY) Only Touring Harley-Davidson Motorcycles are suitable for sidecar use. Consult a Harley-Davidson dealer. Use of motorcycles other than Touring models with sidecars could result in death or serious injury. (00040a) NOTES FL Touring Models equipped with TLE/TLE-Ultra Sidecar require the installation of a Bank Angle Sensor (88115-03). Failure to install and configure a Bank Angle Sensor may result in death or serious injury. Sidecar and Trike configuration of the security system requires the use of a Digital Technician. Consult your Harley-Davidson dealer or the sidecar or Trike service manual for complete details. On vehicles equipped with a sidecar, the security system must be reconfigured from the default solo vehicle setting to the sidecar setting

Incoming search terms: