SUZUKI SV1000 ELECTRICAL SYSTEM SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
COUPLER •With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. (C” -78-14) • * Bend the clamp properly so that the wire harness is clamped securely . • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . ELECTRICAL SYSTEM 7- 3 7-4 ELECTRICAL SYSTEM BATTERY •The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. • Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE HARNESS ROUTING” section. (CJ8-14)

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.

1996 YAMAHA TDM 850 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
Model: TDM850 Model code: 4TX2 5AR1 (CH,A) Dimensions: Overall length Overall width Overall height Seat height Wheelbase Minimum ground clearance Minimum turning radius 2,200 mm 790 mm 1,285 mm 805 mm 1,475 mm 165 mm 2,900 mm Radiator: Radiator capacity (including all routes) 1.7 L Tire: Type Size front rear Manufacturer front rear Type front rear Tubeless 110/80 ZR18 150/70 ZR17 BRIDGESTONE*/PIRELLI/MICHELIN BRIDGESTONE*/PIRELLI/MICHELIN BT54F/MTR03/MACADAM 90X BT54R/MTR04/MACADAM 90X *In Austria and Switzerland only Bridgestone tires are equipped on this mode. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO CARBURETION CARBURETOR FUEL LEVEL ADJUSTMENT 1. Measure: Fuel level a Fuel level: 15.8 16.8 mm (below the MIKUNI mark) Out of specification Adjust. Adjust the float level by slightly bending the float tang 1. Fuel level measurement and adjustment steps: Place the motorcycle on a level surface. Use a garage jack under the engine to ensure that the carburetors are positioned vertically. Connect the fuel level gauge 2 to the drain pipe. MAINTENANCE SPECIFICATIONS SPEC ELECTRICAL Item Standard Limit Voltage: 12 V Ignition system: Ignition timing (B.T.D.C.) Advancer type 10 at 1,150 r/min TPS and electrical type Voltage regulator: Type Model /manufacturer No load regulated voltage Semi conductor-short circuit type SH650A-12/SHINDENGEN 14.1 14.9 V Electric fan: Model /manufacturer NAAF20/NIPPONDEN SO

Incoming search terms: