1993 – 2008 Applicable Models ENGINE BANK 1 AND BANK 2 A/F AND O2 IDENTIFICATION

0

Filed Under (Toyota Manuals) by admin on 25-10-2011

download
This service bulletin provides information on the proper identification of engine bank 1 and engine bank 2 for correct A/F sensor and oxygen sensor replacement. This bulletin contains information that identifies engine bank 1 and engine bank 2 on the following engines: 1AZ-FE, 2AZ-FE, 2AZ-FE (PZEV), 1GR-FE, 2GR-FE, 2GR-FSE, 2JZ-GE, 1MZ-FE, 3MZ-FE, 1UR-FSE, 3UR-FE, 2UZ-FE, 3UZ-FE, 5VZ-FE, and 1ZZ-FE. Bank 1 (B1) refers to the bank that includes cylinder No. 1. Bank 2 (B2) refers to the bank opposite bank 1. Sensor 1 (S1) refers to the sensor that is located before the catalytic converters. Sensor 2 (S2) refers to the sensor that is located after the catalytic converters

2001 Honda GL1800 Oxygen Sensor Replacement Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
REPAIR PROCEDURE 1. Remove the top shelter (see page 2-10 in the Service Manual). 2. Remove the left and right O 2 sensors from the exhaust pipes. • You do not have to remove the exhaust pipes to remove the O 2 sensors. • Be sure to note the wire routing for proper reassembly. 3. Install the new O 2 sensors and route the wires properly (see pages 1-33 and 1-34 in the 2001- Service Manual). 4. Connect the black 4P female coupler of the sub- harness kit to the wire harness side black 4P male coupler (for the left-side O 2 sensor). 5. Connect the new left O 2 sensor to the black 4P coupler on the sub-harness. 6. Route the sub-harness from left to right, across the front edge of the fuel tank and secure it with the clip on the cruise actuator 7. Cut off the right 4P male O 2 sensor coupler (on the wire harness side). 8. Install a PVC cap onto the end of the Black/yellow wire and Green/red wire (these are the wires that were connected to the coupler that was removed in step 7). Fold each cap back and tape it securely to its wire; these wires are no longer used. • Do not cut the wires off, just tape them back. • The tape is supplied in the replacement kit. 9. Strip the ends of the White and Black/red wires (which were connected to the coupler that was removed in step 7) on the wire harness side and the 2P coupler on the sub-harness. Install a heat shrink tube on each wire of the sub harness. 10. Twist the ends of the White and Black/red wires of the sub-harness 2P coupler to the White and Black/red wires of the main harness. 11. Solder the wires using the solder from the kit. 12. Use a heat gun to secure the heat-shrink tubing over the soldered wires. 13. Connect the right O 2 sensor coupler to the white 4P male coupler on the sub harness.

2001 GL1800 Oxygen Sensor Replacement / REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the top shelter (see page 2-10 in the Service Manual). 2. Remove the left and right O 2 sensors from the exhaust pipes. • You do not have to remove the exhaust pipes to remove the O 2 sensors. • Be sure to note the wire routing for proper reassembly. 3. Install the new O 2 sensors and route the wires properly (see pages 1-33 and 1-34 in the 2001- Service Manual). 4. Connect the black 4P female coupler of the sub- harness kit to the wire harness side black 4P male coupler (for the left-side O 2 sensor). 5. Connect the new left O 2 sensor to the black 4P coupler on the sub-harness. 6. Route the sub-harness from left to right, across the front edge of the fuel tank and secure it with the clip on the cruise actuator